• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wiring test before running engine break in

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
I rebuilt my steering column while my engine was out. That electrical and circuits through out the Bronco were "cleaned up". I need to check for power to the ignition and starter circuits before I do my rebuilt engine break-in. Before I attach the battery and turn on the key to do an electrical test what precautions should I take? I have petronics points -will they be damaged with the ignition on and not running? I have a lot of weak suits but electronics is one of my most challenging. Thanks for your time, John B (1973 Bronco, 302, Edelbrock carb.,C4 auto trans.)
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Use you car battery but, use an inline 10 or so amp fuse on either hot or gnd side..
 
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
AZBronco Do you have an inline fuse permanently installed? If ten amps, how much amperage does the starter motor of a 302 draw? My original 1973 under dash wiring was a mess. I bundled it up, including the resistor ignition wire. I'm now thinking I should spend the time to give that line some room, not snugged up to a group of wires. Any experience with that wire getting excessively hot? I hope I'm worrying about nothing. Thanks, John B
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I hope I'm worrying about nothing.
If the fuses are the correct ratings, and you didn't modify any circuits, you are.

The recommendation for a 10A fuse was only for key-on testing; not cranking or running. The starter draws ~140A on a broken-in normal-compression engine. On a fresh rebuild, it might draw >200A the first several starts.

You should put all your truck's details into your signature so they show with each reply.

The resistor wire shouldn't get hot enough to matter. This & the NEXT several pages show the original wiring, but read the captions:

(click this text)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Before I attach the battery and turn on the key to do an electrical test what precautions should I take?

Well, assuming you did this, but quadruple-check for any bare, unused, damaged, crossed wires or any that are close to something that's going to get hot with the engine running is a good start!

I have petronics points -will they be damaged with the ignition on and not running?

YESYESYESYES!!!1
For your initial tests just use the ACC position while you're checking 90% of the truck's electrical components. This leaves both the voltage regulator and the ignition system off and out of danger.
But once you need to turn it to ON to check ignition stuff and whatnot, don't leave it this way for very long. I like to use 1-minute as my maximum time limit.

There is very little you need to check with the key in the ON position anyway. Once you're ON and you know that there are no short circuits or melting components, fire the engine up!

One circuit you can test with the key ON and then START, is the starting circuit and the neutral-safety switch. But for that all you need to do is verify that you get no crank in Drive or any of the other non-start positions, and that you do get cranking in PARK and Neutral. All of which only takes a few seconds of key ON time.

Good luck. It's an exciting time in any builder's life!

Paul
 

charlie6976

Sr. Member
Joined
Jan 19, 2014
Messages
404
Loc.
Grand Coulee WA
Just a thought, isn't there a 'plug' connection on your distributor wiring? And can't you just unplug it while 'testing'?

Hell, pull the coil wire, also. %)
 
Last edited:
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
Paul, you mentioned the voltage regulator - It doesn't have current to it in the acc. mode? Also, the rebuilt engine has been sitting for almost a year. How much can I turn over the engine with the starter? I need to bump the engine until I establish TDC. Thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Paul, you mentioned the voltage regulator - It doesn't have current to it in the acc. mode?

Nope. With factory wiring, and hopefully all the aftermarket harness kits too, both the ignition coil wire and the voltage regulator wire are hot ONLY when the key is in the ON position. No power when in ACC.
They both come off of the same terminal on the back of the ignition switch and are the only circuits hot in both ON and ACC direct from the key.

The reasons are pretty much the same. With the key in the ACC mode while listening to the radio for a couple of hours, or for whatever reason, if you had the main charging system energized you would drain the battery very quickly and with the ignition potentially energized you would burn out the points if you have them, an ignition module if you have that, and perhaps even cause the coil to melt down. Or in extreme cases explode and put hot oil all over your engine compartment.
Which is why ACC is supposed to be a safe-to-leave-on mode and you never hook your ignition system or charging system to an ACC circuit.

And just to keep them separate here, for those reading, the "voltage regulator" being referenced here is the main one for the alternator. The little IVR for the gauges is on the ACC circuit but is not using enough power to create much of an added drain.

Paul
 
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
I installed a full circle aluminum fan shroud from W.Horses. Looks great, should channel the air quite well. Unfortunately there isn't much room to get a socket between the shroad, power steering fan belt and the harmonic balancer bolt. I can't see a reason not to remove the power steering belt for more access - that belt doesn't drive any other components. Then run the engine break-in with the belt removed. Sounds even stupid to ask, unfortunately my brain can miss things. Can't remember the Crank bolt socket size. Anyone know off the top of their head?(1973 302) Thanks John B
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I can never remember the size and always have to try two or three different ones until I "remember" then.;D;)

But if you have not checked yet, there is usually more room for your socket and your arm when accessed from underneath. Might not be enough in ever case, but it's worked on some Broncos.

Paul
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...the rebuilt engine has been sitting for almost a year. How much can I turn over the engine with the starter?
It would be best to pull the distributor & spin the oil pump with a drill for a minute to re-fill all the oil journals & wet all the bearings. A few drops of oil in each spark plug hole will wet the rings. Then you can spin it without damage until the starter gets hot.
 

mustanggarage

Contributor
Sr. Member
Joined
Aug 14, 2018
Messages
647
I am a big fan of the power probe for checking circuits. you can power individual circuits with it, you can test continuity of wires, test switches, test for grounds. it has a built in circuit breaker so if you have a short somewhere you won't damage anything with it. I use this tool all the time when I am wiring. I have now done 3 complete rewire jobs, 2 classic mustangs and the bronco and this tool is a lifesaver.
 

Attachments

  • 51GqTxh5BeL._AC_SL1280_.jpg
    51GqTxh5BeL._AC_SL1280_.jpg
    22.4 KB · Views: 94

Waverous

Contributor
Bronco Guru
Joined
Oct 5, 2001
Messages
2,766
Loc.
Aurora, CO
I am a big fan of the power probe for checking circuits. you can power individual circuits with it, you can test continuity of wires, test switches, test for grounds. it has a built in circuit breaker so if you have a short somewhere you won't damage anything with it. I use this tool all the time when I am wiring. I have now done 3 complete rewire jobs, 2 classic mustangs and the bronco and this tool is a lifesaver.
Ditto on the Power Probe!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I've had one for many years and still have not used all of it's capabilities by a long shot.
First I heard of them was at Off-Road Expo in CA at least 15 years ago now. Saw that and just had to have it!

Been a lifesaver more than a few times.

Paul
 
Top