• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

wobbly side mirror - driver side

buckstone

Full Member
Joined
May 29, 2004
Messages
231
Loc.
los angeles, ca
the driver side mirror on the bronco is real wobbly when i drive - it's the stock mirror, held in place by only two metal screws - looks like the po inserted some plastic screw housings to tighen the base, but it still wobbles like heck when i drive. i'd like to keep the stock mirror - any tips on how i can secure the base better - hopefully without drilling any more holes? perhaps a strong glue/epoxy? thanks.
 

Fathom

Bronco Guru
Joined
May 6, 2004
Messages
1,171
Loc.
Los Angeles
Best thing is to weld the old hole close, grind flat, paint, drill pilot hole, and mount mirror.

If you JB Weld it, it will hold, but you will be creating a mess for later.

just my halh a cent ;D
Fathom
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
the proper half assed way to do it would be- take off the door trim panel and use some screws with nuts on the inside to hold it on. those plastic inserts are the original way to hold it and they wear out.
 

mtkawboy

Bronco Guru
Joined
Jan 28, 2004
Messages
1,525
Loc.
Billings Mt
base is good on mine but I cant figure out how to keep the mirror itself tight. Every time I shut the door I have to roll down the window & adjust it. Any ideas? Sorry to jump in your post
 

mtkawboy

Bronco Guru
Joined
Jan 28, 2004
Messages
1,525
Loc.
Billings Mt
My base has nuts riveted in the door. Maybe you could drill out the old ones and find some new ones to install or center punch around the old ones to tighten them up
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
mtkawboy said:
base is good on mine but I cant figure out how to keep the mirror itself tight. Every time I shut the door I have to roll down the window & adjust it. Any ideas? Sorry to jump in your post

i had one like that because it was cracked where the ball joint was mounted. it took a long trip off a short garbage heap.
 

HotWheels

Bronco Guru
Joined
Jul 8, 2003
Messages
9,179
Loc.
Twilight Zone
jbeyer said:
the proper half assed way to do it would be- take off the door trim panel and use some screws with nuts on the inside to hold it on. those plastic inserts are the original way to hold it and they wear out.

I second this. Use some larger washers to provide a better "stiffener" on the inside. To disperse stress... :D

hth

Mick
 

Skuzzlebutt

PhD, Dr. of Broncology
Joined
May 26, 2001
Messages
4,393
Loc.
Honeymoon Bay
Is the rubber gasket between the the mirror and the door in good shape? That will make a world of difference in steadying the mirror.
How about the door hinges? Worn out hinges allow the door to shake while driving. It's only noticable while looking at the mirror.
 

unclebap

Sr. Member
Joined
Jul 28, 2001
Messages
820
Loc.
High Desert, ca
Skuzzlebutt said:
Is the rubber gasket between the the mirror and the door in good shape? That will make a world of difference in steadying the mirror.
How about the door hinges? Worn out hinges allow the door to shake while driving. It's only noticable while looking at the mirror.

Tend to agree, but worn out hinges make it impossable to listen to the radio, let alone see anything out the mirrows.
 
OP
OP
B

buckstone

Full Member
Joined
May 29, 2004
Messages
231
Loc.
los angeles, ca
the rubber gasket between the mirror base and door panel is in good shape -and door hinges seem tight. one of the screws doesn't tighten that well - as a result, the mirror assembly shakes quite a bit under drive. think i'll drill a third hole through the base and door panel- and attach another screw. hopefully, this will settle it down. the mirror on the passenger side (the one i don't use) is, of course, perfectly solid!
 

mtkawboy

Bronco Guru
Joined
Jan 28, 2004
Messages
1,525
Loc.
Billings Mt
Screw the screw all the way in and take the door panel off and maybe you can put a nut with some red locktite on it to tighten it down. Mine has rhe removable panel and I dont know if yours does
 
OP
OP
B

buckstone

Full Member
Joined
May 29, 2004
Messages
231
Loc.
los angeles, ca
as far as i can tell, the door panel isn't removable. the panel pieces seem welded together and painted over. so, don't think i'll be able to take it apart. i'll try my best with a third hole,machine screw with plastic insert.
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
buckstone said:
as far as i can tell, the door panel isn't removable. the panel pieces seem welded together and painted over. so, don't think i'll be able to take it apart. i'll try my best with a third hole,machine screw with plastic insert.

is it the plastic or metal panel. dumb question-we are talking about the inside of the door, right?
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
those should be held on with wire spring clips. you have to be carful to not crack the fiber board, but the come off fairly easily.
 

jbeyer

Bronco Guru
Joined
Mar 3, 2004
Messages
1,679
Loc.
new york city
HotWheels said:
strange...maybe this is the panel with climps as opposed to screws?

ive got the metal panels. i know on some models they tried to make it look like a car, and had padded vinyl panels. i assumethat whats going on here.
 

HotWheels

Bronco Guru
Joined
Jul 8, 2003
Messages
9,179
Loc.
Twilight Zone
jbeyer said:
ive got the metal panels. i know on some models they tried to make it look like a car, and had padded vinyl panels. i assumethat whats going on here.

mine were paded. when i sold them...the guy cussed me out for altering them. some people. they were that way on my 77 and matched my seats perfectly.
 
Top