• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

ZF5 install parts list

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
I have a superlift 3.5" suspension lift with 1" bodylift, no issues with driveline angle. Been running this setup for a few years without issue. I am running stock rebuilt driveshafts that have had their lengths changed (zf/205 is longer than the stock 3speed/d20

Sent from my SM-G981V using Tapatalk
 

Mikes Early Bronco

Contributor
Oily Driveway Guy
Joined
Nov 8, 2008
Messages
146
Great help

Thanks so much for the help. I'm ordering now. I'll be sure to get the shims. This week I ordered the crossmember from BC. I was told that its a new design. I wasn't sure what that meant but maybe they addressed the previous issues. If not I'll cut and weld. Thanks again guys. It seems that I have this ironed out now but I'm sure I'll have a few questions along the way.
 
OP
OP
Big Slim

Big Slim

Full Member
Joined
Dec 11, 2007
Messages
339
So I did some measurements for the shifter hole. I measured 13.25” from the front of the trans to the shifter down the center line. Transferring that to the tub I got 3.75” from the driver side hump and 1.75” from the front where it starts to angle up. Does this seem like the right spot?
2ae514f6edd3af4bc3dbcbffc1a37048.jpg
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
The leading edge on mine is cut at the crease where the tunnel kicks up

From the driver's side edge I've got 2"to the edge of the shift hole and from the passenger side edge I've got 3 3/4"

Hopefully that helps. First picture is from the driver's side, second is from the passenger side
bfe8714321a1241a22a9e2201c9792ea.jpg
980d18a22d47ac9e05319b43b2538af2.jpg


Sent from my SM-G981V using Tapatalk
 
OP
OP
Big Slim

Big Slim

Full Member
Joined
Dec 11, 2007
Messages
339
Perfect. That’s real close to my measurements. About 1.25 off of center to the drivers side.
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
No it can't, I wanted to try and get rid of it but the shifter needs the tower to actuate. The only mod I've found is a short throw kit, but you'll still use the same shift tower.

Sent from my SM-G981V using Tapatalk
 
OP
OP
Big Slim

Big Slim

Full Member
Joined
Dec 11, 2007
Messages
339
Oh. I meant just for the process of installing the trans. Then install the shifter from the top side once in place.
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
Yeah you can take it off for that, I think I did the same thing when I installed mine.

Sent from my SM-G981V using Tapatalk
 
OP
OP
Big Slim

Big Slim

Full Member
Joined
Dec 11, 2007
Messages
339
Last edited:

hankjr

Contributor
Bronco Guru
Joined
May 11, 2013
Messages
1,761
i used an-4 and i retained the quick connect at the slave end. i dont recall how i connected but i dont think i purchased a special end but reused one from a clutch line i got from rock auto for the f250 the tranny came out of. i can go out to the shop later and take a look.

Hank
 

1968Ford Bronco

New Member
Joined
Sep 13, 2022
Messages
6
What cross member are you running with this? I got the kit from BC and their crossmember does not even fit the ZF5 4X4 transmission properly without shimming the mount with 1/2" spacer to get the transmission off of the crossmember as well as with the Atlas TC I do not believe the front driveline will even clear the crossmember?
 

1969

Contributor
Bronco Guru
Joined
Feb 28, 2022
Messages
1,090
Loc.
Reno, NV
What cross member are you running with this? I got the kit from BC and their crossmember does not even fit the ZF5 4X4 transmission properly without shimming the mount with 1/2" spacer to get the transmission off of the crossmember as well as with the Atlas TC I do not believe the front driveline will even clear the crossmember?

If you look in my build thread you will see how I modified their cross member instead of stacking washers.
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
What cross member are you running with this? I got the kit from BC and their crossmember does not even fit the ZF5 4X4 transmission properly without shimming the mount with 1/2" spacer to get the transmission off of the crossmember as well as with the Atlas TC I do not believe the front driveline will even clear the crossmember?
I installed that BC crossmember about 10 years ago, they may have changed their crossmember to the point of it not fitting well (not sure why they changed it, it fit pretty well). Sorry to hear you're having issues with it.
 

1968Ford Bronco

New Member
Joined
Sep 13, 2022
Messages
6
If you look in my build thread you will see how I modified their cross member instead of stacking washers.
One heck of a build you have and thanks for the help, do you have any pictures or did you have any issues with the crossmember and the front driveline?
 

1969

Contributor
Bronco Guru
Joined
Feb 28, 2022
Messages
1,090
Loc.
Reno, NV
One heck of a build you have and thanks for the help, do you have any pictures or did you have any issues with the crossmember and the front driveline?

I haven’t gotten to the drivelines yet but they look like they should clear.
 
Top