• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

d44 narrowing , cast wedges?

cnielsen413

Jr. Member
Joined
Feb 19, 2007
Messages
50
Loc.
petaluma, CA
im looking for a d44, i found a full d44 out of a late 70's bronco, with cast wedges setup for radius arms. its a high pinion. can i make this work? or does the cast wedges pose a problem for narrowing?
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Cleanest solution IMO to shorten a 78-79 D44HP axle is to do a WAH.

Otherwise, you can pull the tube, remachine it, and reinstall it if you've got the tooling and skill to get it done. The next option would be to cut, section, and butt-weld it. If done properly, the weld should be stronger than the surrounding material...if not, then it will be a spectacular picture worthy failure. I'd hazard a guess that the weakest point on those axles is at the cast C's based on wall thickness I've seen in various cross-sections people have made.
 
OP
OP
C

cnielsen413

Jr. Member
Joined
Feb 19, 2007
Messages
50
Loc.
petaluma, CA
Hmm, WAH? im a newbie, appologies! :)

I have the tooling, to machine it, but i guess id have to take it appart to see what you mean, if i pulled it off, Id have to cut one end, and then re machine what? Im not against the butt weld, but if i can avoid it, i would. Thanks guys!
 

Bronco73

Contributor
Bronco Guru
Joined
May 29, 2003
Messages
3,016
Loc.
Cape Coral, FL
the cast wedge on the pass side can be pulled off after you cut the weld. once removed cut the axle tube to length and then press the cast wedge back on and set the camber caster and reweld. IMO this is much easier and way cheaper. theres a link in my other post explaining this process.
 

Steve

Bronco Guru
Joined
May 5, 2003
Messages
2,986
Loc.
Grand Junction, CO
the cast wedge on the pass side can be pulled off after you cut the weld. once removed cut the axle tube to length and then press the cast wedge back on and set the camber caster and reweld.

No, on axles with cast wedges the wedges are actually part of the axle tube. There is no tube under the wedges so they cannot be cut off or moved.
 

Bronco73

Contributor
Bronco Guru
Joined
May 29, 2003
Messages
3,016
Loc.
Cape Coral, FL
No, on axles with cast wedges the wedges are actually part of the axle tube. There is no tube under the wedges so they cannot be cut off or moved.

the cast piece is pressed on the tube end. how do you think its on there? the axle tube is inside the cast wedge and then it is welded on the end.

heres the correct link to my first look at narrowing the FS axle.
http://classicbroncos.com/forums/showthread.php?t=115968

heres a link showing how the cast wedge is removed and then the tube cut down and the cast piece pressed back on and welded. it's pretty straight forward.
http://www.therangerstation.com/tech_library/narrowing_a_ford_dana44.htm
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
Now that is news to me too, excellent link! I just so happen to have one to practice on coming up too! ;D
Only thing that sucks is that you cant change caster and pinion angle separate.
 

Bronco73

Contributor
Bronco Guru
Joined
May 29, 2003
Messages
3,016
Loc.
Cape Coral, FL
Now that is news to me too, excellent link! I just so happen to have one to practice on coming up too! ;D
Only thing that sucks is that you cant change caster and pinion angle separate.

i hope to attempt and complete this on Sunday. i will take pics.
 

scsm76

Bronco Guru
Joined
Oct 6, 2005
Messages
1,433
Loc.
Shaver Lake, CA
Now that is news to me too, excellent link! I just so happen to have one to practice on coming up too! ;D
Only thing that sucks is that you cant change caster and pinion angle separate.
Actually you can, you just can't change the position of the wedges reletive to the inner c's. So you just have to get your caster where you want it using degreed bushing's and/or the radius arms. Although with the the HP there usally isn't a need for pinion angle changes.
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
Yeah thats what I was trying to say. Might also be tough to get to the driver side as well its pretty tight in there. It is cool to know that there is actually a weld there with some tube overlap. And like you said pinion angle isnt a big deal with the HP.
 

Steve

Bronco Guru
Joined
May 5, 2003
Messages
2,986
Loc.
Grand Junction, CO
the cast piece is pressed on the tube end. how do you think its on there? the axle tube is inside the cast wedge and then it is welded on the end.

I think we're saying the same thing but in different ways. Cast wedges, unlike welded ones, aren't simply welded on top of the axle tube. Yes, you can narrow them, but if you simply try to cut the wedges off you're screwed because, unlike the welded wedges, there is no separate tube under the cast wedges.

Look at pics 14,15 & 16 on the definitive Dana axle web site.
 

Bronco73

Contributor
Bronco Guru
Joined
May 29, 2003
Messages
3,016
Loc.
Cape Coral, FL
When I refer to the cast iron piece or wedges I am refering to the complete casted end on the 78.79 axle, not just the wedges. I should be a little more clear on that. I just figured since the topic was on the 78/79 axle that everyone knew the cast wedges are part of the complete end on the 78/79.

I've been to the axle site several times.

Are the pre 77.5 axles with the welded on wedges (<>) cast or steel?
 

Steve

Bronco Guru
Joined
May 5, 2003
Messages
2,986
Loc.
Grand Junction, CO
When I refer to the cast iron piece or wedges I am refering to the complete casted end on the 78.79 axle, not just the wedges. I should be a little more clear on that. I just figured since the topic was on the 78/79 axle that everyone knew the cast wedges are part of the complete end on the 78/79.

In my experience I'm not convinced everyone knows that.

Are the pre 77.5 axles with the welded on wedges (<>) cast or steel?

Steel.
 

ricky

Full Member
Joined
Mar 28, 2007
Messages
310
Loc.
beaumon,texas 77706
what if you have access to a hig pinion with spring mounts? and want to narrow it for a bronco? i am thinking of doing this as i have access to both a hp 44 and rear 60..do not mean to high jack the thread
 

scsm76

Bronco Guru
Joined
Oct 6, 2005
Messages
1,433
Loc.
Shaver Lake, CA
what if you have access to a hig pinion with spring mounts? and want to narrow it for a bronco? i am thinking of doing this as i have access to both a hp 44 and rear 60..do not mean to high jack the thread
You can narrow it just the same and you can add wedges to it, but they will have to be ground down to fit the larger diameter tube or you will need to run spacers between the radius arms and caps. The amount you narrow it will vary depending on what year the housing came from and the outer stubs shafts are different from the 1/2 ton's and bronco's.
 

ricky

Full Member
Joined
Mar 28, 2007
Messages
310
Loc.
beaumon,texas 77706
ah,i was wondering, they are 3/4 ton axles and are under my 1993 truck right now,they are built with 4.88's and all,so was thinking of using them,plus i have my wheels/tires which are 8 lug..i was only going to run a 2" body lift and 4.5 suspension lift,the tires i have right now are 16.5-15 welds and 39-18.8-16.5 m/t's i'm thinking they are going to look too big on the bronco,even narrowed
 

scsm76

Bronco Guru
Joined
Oct 6, 2005
Messages
1,433
Loc.
Shaver Lake, CA
ah,i was wondering, they are 3/4 ton axles and are under my 1993 truck right now,they are built with 4.88's and all,so was thinking of using them,plus i have my wheels/tires which are 8 lug..i was only going to run a 2" body lift and 4.5 suspension lift,the tires i have right now are 16.5-15 welds and 39-18.8-16.5 m/t's i'm thinking they are going to look too big on the bronco,even narrowed
If those axles came on the 93 there will be an issue of fitting the wedges on the passenger side tube, because the newer front ends are offset more to the driver side. There are a few ways to make them work however. Wouldn't the rear end in that truck be a Sterlling not a Dana? Either way it would work. With that size tire you would probably want to leave them full width.
 

ricky

Full Member
Joined
Mar 28, 2007
Messages
310
Loc.
beaumon,texas 77706
i'm not sure what year the axles are,whats the easiest way to find out? i bought them from a guy several years ago,i'm thinking they were late 70's units..the truck is a original two wheel drive f150 that we converted to a straight axle setup with leaf springs,etc about 15" lift and all..i just never drive it anymore and was thinking of putting the drivetrain in the bronco since that big ole truck will be hard to sell nowdays..keeping them std width i think would have the tires sticking wayyy to far out for me to drive it on the streets
 
Top