• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

More Full width questions??

spennyluv

Jr. Member
Joined
Dec 8, 2005
Messages
88
Loc.
bay area
I found a full width 44 out of a later model bronco but it has cast wedges and not weld on what is the negative to that i know that the coild springs will bow a little but couldnt i just move the coild plate over a little. I have WH extended radius arms right now will those work i notice a lot of you guys with full width axles are running cage extended arms. What is the best way to center the axle front and rear? And how do i measure what kind of shims i need for my raerend my drive shaft is at a very steep angle with my 4bt zf np 205 set up.
Thanks again for all the great info
 

trailbound

Full Member
Joined
Feb 13, 2007
Messages
217
i just got back from WH, cause i am doing the same thing to my rig right now. They said that w/ their arms, and a 3.5-5.5 lift you should run 4* bushings. As far as the front goes, you should be able to just center is up and pull the coils over to the cups. you can turn the cups 180* to bring them in a little but it would hurt anything to just bring the coils over. As far as the rear goes, because of the added lenght of the zf/205 I 'm not quite sure if shimming is gonnna be an option for you. Because either way you're still gonna have a really short drive line. One option will take some work but you could push your rear back 2-4 inches and that will help, but to do so would involve grinding off your existing hinges and relocating them to the new location.
right now I'm working on a bracket to tie my WH arms into for the full width, when i get them all mocked up I'll post some pics.
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
Any of the extended arms will work OK with the 78/79 full width conversion. You could even use stock arms if you want, as the wedges on the 78/79 are angled inward slightly more than on the EB dana 44. As for the springs, we prefer to move the coil buckets out. You only need to space them about 2" outboard of the frame rails to get them right over the lower coil cups. Here's a pic of how we did it on a recent project rig at WCB:

dscn9491.jpg

(For more pix of that build check it out on our site at http://www.wcb4x4.com/proj/mccarthy70/index.shtml)

We'll be offering a DIY full width conversion kit soon that includes a production version of the bucket spacers. It will be a lasercut brake-formed piece that will make it pretty easy to just cut off your buckets then weld them back on with the spacers.

Dusty
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
Dusty, I like the bracket for the buckets there, thats pretty slick. With your brackets will you be able to also raise the bucket as well so you could run a taller coil but keep the height down?
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
The bracket will be quite a bit different from the pieced-together one in the photo above. The top of it will come down onto the top of the frame rail, with a notch so it indexes correctly on the top of the rail. We're doing this both so it will have extra support and so it will be more of a no-brainer when people weld it on. Unfortunately for your needs this makes it specific for the stock bucket height. You could move the bucket up but you would have to back-fill (plate in) the area under that step, which would basically defeat the purpose of having an easy to use weld-on plate since it would require extra fabrication.

But you bring up an interesting point. Is there a market for a similar piece that raises the coil bucket higher than stock, along with the spacing for the full width? If so, what would be the prefered bucket height--1" higher than stock? 2"?

Thanks for the input Tito.

Dusty
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
Not sure of the market, probably not real big but 80% would want 2" I am sure so they could run 5.5 coils with only 3.5" lift. The others would probably want 1" or 3" to run 3.5" or 5.5" coils with only a 2.5" susp lift. The majority of these folks would probably be running stock width too I'd figure. Not sure of the market as I am sure a lot of the people who would be doing something like this would just bump up their stock buckets but it would be nice to have a new bucket offered that would be longer and just trim it to fit the height you want.
 

scsm76

Bronco Guru
Joined
Oct 6, 2005
Messages
1,433
Loc.
Shaver Lake, CA
Not sure of the market, probably not real big but 80% would want 2" I am sure so they could run 5.5 coils with only 3.5" lift. The others would probably want 1" or 3" to run 3.5" or 5.5" coils with only a 2.5" susp lift. The majority of these folks would probably be running stock width too I'd figure. Not sure of the market as I am sure a lot of the people who would be doing something like this would just bump up their stock buckets but it would be nice to have a new bucket offered that would be longer and just trim it to fit the height you want.
With all the variables an adjustable bucket might be the best solution, then you could change your mind about ride height without swapping coils or account for settling at either end. As long as you could sell them at a reasonable price.
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
With all the variables an adjustable bucket might be the best solution, then you could change your mind about ride height without swapping coils or account for settling at either end. As long as you could sell them at a reasonable price.

I have seen them for the rear from ballistic fab, they are pretty cool. This would be real cool to play with. Of course then I'd want a set of 7.5" lift coils for mine so I could keep the 5.5" lift and get sprung ;D
 

PsYcHoBrOnCo

Sr. Member
Joined
Oct 3, 2005
Messages
575
Loc.
Fort Worth, Tx
The bracket will be quite a bit different from the pieced-together one in the photo above. The top of it will come down onto the top of the frame rail, with a notch so it indexes correctly on the top of the rail. We're doing this both so it will have extra support and so it will be more of a no-brainer when people weld it on. Unfortunately for your needs this makes it specific for the stock bucket height. You could move the bucket up but you would have to back-fill (plate in) the area under that step, which would basically defeat the purpose of having an easy to use weld-on plate since it would require extra fabrication.

But you bring up an interesting point. Is there a market for a similar piece that raises the coil bucket higher than stock, along with the spacing for the full width? If so, what would be the prefered bucket height--1" higher than stock? 2"?

Thanks for the input Tito.

Dusty

I am in the process of raising my spring cups 2 inches, I have a 5.5 Cage lift kit with FW axles...your product will be very marketable when offered to the public.
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
Dusty - any update on your product?

We were hoping to have the first articles back from the job shop by now (we were hoping to have them to show off at the Big Bear Bronco Bash this weekend). But it doesn't look like that will happen. Hopefully sometime in the next couple of weeks.

Dusty
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
We were hoping to have the first articles back from the job shop by now (we were hoping to have them to show off at the Big Bear Bronco Bash this weekend). But it doesn't look like that will happen. Hopefully sometime in the next couple of weeks.

Dusty

Thanks for the response - I've got a 90' D60 I want to put under the 74' with Cage Arms & Coils.... I'm sick of tripping over them!
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
If you're sticking a D60 under there you have to weld the wedges or the CAGE brackets onto the housing anyhow. Why not just put them at EB width and leave the coil buckets where they are? The coil bucket extensions are intended mostly for use with the 78/79 high pinion D44 with the cast wedges, which are impossible to move inboard.

Dusty
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
If you're sticking a D60 under there you have to weld the wedges or the CAGE brackets onto the housing anyhow. Why not just put them at EB width and leave the coil buckets where they are? The coil bucket extensions are intended mostly for use with the 78/79 high pinion D44 with the cast wedges, which are impossible to move inboard.

Dusty

I'm not sure if I can get the drivers side close enough - there isn't much room between the knuckle and the pumpkin. I posted about this earlier - will it even line up? I'd love to weld the brackets on the axle so that they would line up to the EB frame - but is there enough room?
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
OIC, you've got the super duty 60 with the pumpkin closer to the driver side. Yeah I can see how you might have a problem. On my D60 I put the wedges at EB width but its a 79 D60 with the pumpkin not so far offset.

Dusty
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Exactly - it is a 90' Kingpin D60.. Some fabrication may be required - you brackets may meet the list. I've got these really beefy coil buckets though - maybe I could make some osrt of heavy wall rectangular tubing spacer.

 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
That's what I would do if I were you, fab your own spacer. The one we're working on is going to form-fit to the stock coil bucket, which has rounded corners. It looks like they would require some extra cutting and trimming to use with your Duff's buckets. I wouldn't use rectangular tubing though, get some plate steel and fabricate a custom-looking one. Making everything out of rectangular tubing just looks a little too farm-fab.

Dusty
(no offense to the farm-fabbers out there--I grew up on the farm too, making everything out of angle iron and old piece of railroad track!)
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
That's what I would do if I were you, fab your own spacer. The one we're working on is going to form-fit to the stock coil bucket, which has rounded corners. It looks like they would require some extra cutting and trimming to use with your Duff's buckets. I wouldn't use rectangular tubing though, get some plate steel and fabricate a custom-looking one. Making everything out of rectangular tubing just looks a little too farm-fab.

Dusty
(no offense to the farm-fabbers out there--I grew up on the farm too, making everything out of angle iron and old piece of railroad track!)

Ok - It wouldn't be done like that. I ordered buckets for a 78-79 OEM replacement and got those - I like em, they are tough! Thanks for your input - I apreciate it!
 

GRN_MEANIE

Sr. Member
Joined
Aug 2, 2005
Messages
553
No really why would you want the longer coils? w/o any gain in height or travel?
 
Top