• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

94-95 mustang EEC-IV pin 41 question

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
OK, working on another project. Trying to do EEC-IV controlled 4R70w instead of the Baumanator. So I am getting everything done up to pin 41, the TCS (transmission control switch) The factory wiring manual I have shows this wire coming off a transmission module. Module has 6 wires; power, ground, switch, light, and a wire going to pin 41. I am very confident that it is mearly a latching switch to turn the light on and send a signal to the EEC. I am fairly sure that all I need to keep the overdrive off is either grounding or powering this wire. but I don't know which. figured I would look around (couldn't find my answer) so I will now ask. Next step, guess.

So does anyone know the logic of pin 41 on a '94 mustang automatic transmission computer?
 

RnrdTheFox

Sr. Member
Joined
Dec 4, 2005
Messages
727
Loc.
Superior, CO
OK, working on another project. Trying to do EEC-IV controlled 4R70w instead of the Baumanator. So I am getting everything done up to pin 41, the TCS (transmission control switch) The factory wiring manual I have shows this wire coming off a transmission module. Module has 6 wires; power, ground, switch, light, and a wire going to pin 41. I am very confident that it is mearly a latching switch to turn the light on and send a signal to the EEC. I am fairly sure that all I need to keep the overdrive off is either grounding or powering this wire. but I don't know which. figured I would look around (couldn't find my answer) so I will now ask. Next step, guess.

So does anyone know the logic of pin 41 on a '94 mustang automatic transmission computer?

Yes, it's a latching function. No voltage to the pin, the overdrive is engaged. 12V will disengage the overdrive. I never could find the module in a yard to snag so I ended up making a latching circuit with two 12V flip-flops. It clears when the key is turned off and upon starting. It will hold the overdrive off when I press the O/D button on the column shift handle then clears when I turn the ignition off.
 
Last edited:

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
Here are a couple of schematics for the 5.0 94-95 Mustang OBD I. The transmission control module is just a latch for a momentaty push botton that clears when the ignition is turned off or the botton is pressed again. I think it was done that way to keep the chassis wiring compatable with the other engine/tranny combos. They run the wire directly from the push botton to the PCM that debounces and latches the function. They also have a wire that runs back to the dash from the PCM for the indicator light. Those are OBD II computers, I believe. I hate mystery boxes on schematics!

A toggle switch might work fine. I'm not sure if it has issues with function engaged at startup of if switch bounce would be a problem. I think that they just didn't want people to leave the OD off all the time. That's my guess.

tan/wht goes to pin 41
blk/wht is ground
 

Attachments

  • IMGP0001-2 (Large).JPG
    IMGP0001-2 (Large).JPG
    63.2 KB · Views: 82
  • IMGP0001 (Large).JPG
    IMGP0001 (Large).JPG
    52.3 KB · Views: 75
Last edited:
OP
OP
Broncobowsher

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
That works great. Apply 12V and OD is off. I was going to start with grounding it, but 12V was choice #2. I was thinking that was it as well. I am just going to run a toggle.

The neat part, my factory engine wiring books show different then those factory body wiring books. Just goes to show how much fun some of this stuff is.
 
Top