• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Help! Door Hinge Backing Plate

OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Some good ideas I hadn't thought of, thanks guys!

One thing though - The backing plates float because thats how you are able to line up the doors properly, right?

Tacking the plate in place would be a cinch if I could do it fast enough to not catch the Rhino on fire. I can't get a nut onto any of the bolts, they're all broken off flush or inside the threads. Heating them up and penetrating oil would be my only option before drilling them. I'm going to try all ideas before cutting the inner fender or kick panel though, Thanks!
 

admin

Administrator
Just your friendly, neighborhood webmaster...
Joined
Jan 1, 2001
Messages
38,897
Loc.
Phoenix, AZ
One thing though - The backing plates float because thats how you are able to line up the doors properly, right?
Correct. They float a little because they're cradled loosely by the "box" that surfer-b mentioned. The "box" is why they don't fall all the way down once you unbolt the door hinges.

On the top hinge it looks like you've got 1 clean hole. I would thread a bolt in there and tighten ALOT. Then drill out the other 2 bolt shafts that are stuck in the holes.

For the bottom hinge how about drilling a new hole in the center of the 3 bolts? Drill it all the way through both the door post and backing plate. The backing plate will flop around a bit while you're doing this, but the inner box should keep it in place somewhat. Then use a tap to thread it. That way you can put a bolt in it to hold the backing plate tight while you drill out the 3 factory bolts. Once you're done, unbolt your new center bolt and you don't even have to weld up the hole since the hinge will cover it.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Correct. They float a little because they're cradled loosely by the "box" that surfer-b mentioned. The "box" is why they don't fall all the way down once you unbolt the door hinges.

On the top hinge it looks like you've got 1 clean hole. I would thread a bolt in there and tighten ALOT. Then drill out the other 2 bolt shafts that are stuck in the holes.

For the bottom hinge how about drilling a new hole in the center of the 3 bolts. Drill it all the way through both the door post and backing plate. The backing plate will flop around a bit while you're doing this, but the inner box should keep it in place somewhat. Then use a tap to thread it. That way you can put a bolt in it to hold the backing plate tight while you drill out the 3 factory bolts. Once you're done, unbolt your new center bolt and you don't even have to weld up the hole since the hinge will cover it.

Yeah, I think Surfer-b and I were typing at the same time, lol! The center bolt idea is a great one. That'll do all I need and won't have to worry about things getting to hot and going up in flames. THEN I can play with some heat and try to extract the bolts. Woo Hoo, I now have a plan!!!! ;D
 

mcdobson

Sr. Member
Joined
Jul 28, 2008
Messages
401
Loc.
Sacramento
All the bolts countersink into beveled holes in the sheet metal so they center them selves. I don't understand how they would be used for adjustment.
 

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
this must be one of the most common issues with the EB.

i can't even get my passenger side hinges off because the last guy who took the doors off used big phillips head bolts :( and they are somewhat stripped.

the backing plates really just float around in loose box mount? it seemed as if mine were tacked into place. plus the last guy did a shit job of tapping the hole and i am lucky my doors even shut.

do you have to cut a hole in your fender to put a new backing plate back there? is it even worth trying to replace and opening up that can-o-worms?
 

admin

Administrator
Just your friendly, neighborhood webmaster...
Joined
Jan 1, 2001
Messages
38,897
Loc.
Phoenix, AZ
All the bolts countersink into beveled holes in the sheet metal so they center them selves. I don't understand how they would be used for adjustment.
These bolts aren't into sheet metal. They're through the door hinge plates and then into the "floating" backing plate inside the front door jamb. The backing plate being able to move around a little is what allows the adjustment.
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
this must be one of the most common issues with the EB.

i can't even get my passenger side hinges off because the last guy who took the doors off used big phillips head bolts :( and they are somewhat stripped.

the backing plates really just float around in loose box mount? it seemed as if mine were tacked into place. plus the last guy did a shit job of tapping the hole and i am lucky my doors even shut.

do you have to cut a hole in your fender to put a new backing plate back there? is it even worth trying to replace and opening up that can-o-worms?[/QUOTE]

If you have the fender off or take it off, you can cut a three sided window in the back of the door post and remove them to repair or replace, then weld it shut. That can sometimes be an issue as the three phillips head bolts holding the fender on are about as bad to get out as the hinge bolts.
 

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
ha, so no matter what i have to deal with phillips head bolts :(

so if the fender is affixed by those phillips head bolts too? why would ford do that?
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
I think they had a surplus of the darn things and were trying to use them up. They've given me trouble every single time. If they don't come out with an impact driver, I just drill, retap and put in reg hex head bolts. The hinge bolts are hex head, a PO must have had a blonde moment when he put those in.
 

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
yeah it really sucks- i had to leave the hinges on the pass. side and duct tape em so they wouldn't swing out every time i made a right turn %)
 

bronco-kid

Jr. Member
Joined
Dec 7, 2009
Messages
102
Loc.
roanoke
take the hindge off the door,if you have one good hole bolt it back in place .that should keep the backing plate still so you can drill it.good luck!!!
 

mtnkraus

Full Member
Joined
Feb 22, 2004
Messages
229
Loc.
Iowa
I am putting on new door posts to fix this problem. I will take a picture of the back side of the post to see the retaining features.

One Idea- After playing this these I would look at cutting out the back side of the post inside the fender then welding a plate back in that area. I would do this ONLY IF THE BACKER PLATES HAVE RUSTED OUT OF THE FLOAT PLATE RETAINING FEATURES.

Just an Idea.
 

Attachments

  • IMG_0229_1.JPG
    IMG_0229_1.JPG
    66.9 KB · Views: 153
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Ok, so I finally tried to deal with my broken bolts. I started on the passenger side door where only the bottom hinge was screwed up. I was going to try to weld something onto what was left of the broken bolt but I couldn't get anything in there, line it up and weld it. I drilled out the bolt and put my Ez-Out in it. I couldn't get it to budge and this is after a month of soaking it with PB Blaster.

I then decided to go with Jon's idea to drill a hole in the center of the hinge plate and tap it so I could use a bolt to hold it still while I drillout the other bolts. It worked. Now I just need some sharp drill bits that won't wallow out the hole or walk around. As you can see I didn't get things drilled very well but I'm hoping it'll be close enough. On the Driver's side, I'm going to grind everything flat and then drill.
 

Attachments

  • Door Hinge (2).jpg
    Door Hinge (2).jpg
    286.8 KB · Views: 117
  • Door Hinge (1).jpg
    Door Hinge (1).jpg
    154.8 KB · Views: 131
  • Door Hinge.jpg
    Door Hinge.jpg
    153.9 KB · Views: 152

Ratch

Contributor
Sr. Member
Joined
Nov 1, 2007
Messages
695
Ok, so I finally tried to deal with my broken bolts. I started on the passenger side door where only the bottom hinge was screwed up. I was going to try to weld something onto what was left of the broken bolt but I couldn't get anything in there, line it up and weld it. I drilled out the bolt and put my Ez-Out in it. I couldn't get it to budge and this is after a month of soaking it with PB Blaster.

I then decided to go with Jon's idea to drill a hole in the center of the hinge plate and tap it so I could use a bolt to hold it still while I drillout the other bolts. It worked. Now I just need some sharp drill bits that won't wallow out the hole or walk around. As you can see I didn't get things drilled very well but I'm hoping it'll be close enough. On the Driver's side, I'm going to grind everything flat and then drill.

Hey mike, since you have the hinge stable, you might want to just carefully grind off the rest of the broken bolts flush with the hinge plate, line hinge up with paint marks on the post, center punch. drill and re-tap the correct size. might get it close with a die grinder, and finish the grind with a dremmel. Just a thought.
P.S. I have a 1/8" high speed air dremmel if you need to borrow it.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
Hey mike, since you have the hinge stable, you might want to just carefully grind off the rest of the broken bolts flush with the hinge plate, line hinge up with paint marks on the post, center punch. drill and re-tap the correct size. might get it close with a die grinder, and finish the grind with a dremmel. Just a thought.
P.S. I have a 1/8" high speed air dremmel if you need to borrow it.

It's worth a try. Let me see how I do with my ginders (I have an electric dremel) but your help is always welcome!
 

Ratch

Contributor
Sr. Member
Joined
Nov 1, 2007
Messages
695
No problem, how we looking on the cookout? I have to work this sat, but I could be there by about 4:30.
 
OP
OP
msweb

msweb

Bronco Guru
Joined
Aug 29, 2003
Messages
2,377
No problem, how we looking on the cookout? I have to work this sat, but I could be there by about 4:30.

Need to check with the guy with the property or do it at the park. I'll let ya know as soon as I do.
 
Top