• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Sheared Dist Gear Pin / HV Oil Pump??

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
Yesterday the Bronco came home on a shiny new $118K flatbed. I pulled the stock distributor this morning. The drive gear had a pin in it that appeared to be about 3 layers of rolled sheet metal not the "conventional" black c shaped split pin. The pin hole in the dist shaft is is oblong and at least .010 out of round. The gear pin hole is still round and 1/8 in dia. The drive gear teeth are shiny on one side with no apparent wear. The shaft of the distributor is knurled (re-builder?) under the upper half of the gear which is just the boss that the split pin goes into. There is no support under the gear teeth. Actually is has about .004 slop that would allow the gear to wobble on the shaft and weaken the roll pin when it was under load pumping lots of oil. It was a rebuild from the local auto parts. Engine has about 10K since it was rebuilt. I am debating whether to put in a stock pump or leave the HV pump in after I go fishing for some little pieces of roll pin that are in the pan.

I don't need an after market hot rod distributor. A new stock re-placement would be fine or a rebuilt that was re-built to last with a new shaft and gear that is tight on the shaft. Anyone know of a quality re-builder or a stock Made in USA replacement? I have had no experience with either Mallory or Pertronix other than the pickup now in the stock distributor. Does anyone have any preference for a stock replacement?

I had what I thought was a stock new oil pump on the shelf. Looking at the casting it has "M68HV" and the strange letters "USA" cast in the side. I assume it is another HV Melling pump like I have in the engine
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
had the same thing happen to my pertronix distributor jerry, and they stood behind it. i took it to them next day, they looked at it for about 3 seconds, and gave me a brand new one. i thin the HV pump may have been a factor too, but haven't changed my pump and haven't had a problem since. i now run thinner oil too though.

if you're gonna drop the pan, i'd change to a standard pump.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I've been running a HV pump for many years and have yet to have any issues. I've had similar issues with a dizzy in a 460 once just got another stock replacement and never had another issue. But it sounds like your dizzyy was rebuilt in the past and just patched up to make it work. I'd just go to your local parts store and get a rebuilt unit I know autozone has a lifetime garruntee on theres so youif you have any issues at least you'll have free replacement. I would look at the roll pin in the new dizzy might consider swapping it if its another rolled metal pin.
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
Ive used HV pumps in every ford I ever rebuilt bout 20 of em NEVER had an issue!!!
 

iwlbcnu

Contributor
Bronco Guru
Joined
Nov 1, 2001
Messages
3,349
Being rebuilt I wouls suspect there was slop in the hole from them reinstalling the gear and having to clearance the hole. Have you checked to make sure the top of the shaft still turns?? I just had one do the same thing, but it also broke the shaft in half, the weights in the dizzy came apart and locked it up. You could have a dizzy bearing seizing.
In the 5.0 world, the stock pump shafts are known to twist from HV pumps, but they always go before the dizzy will. I have never lost a dizzy to one.
 

bludorbronc

Sr. Member
Joined
Apr 19, 2006
Messages
653
drill out the holes and find a pin that one fits inside the other to make a double wall pin.
 

dbevans2249

Sr. Member
Joined
Sep 21, 2003
Messages
610
Loc.
Buena Park, Ca.
72Sport You can give Ignition Engeneering a call to get a great Distributor. Since you are in So Cal it is not far away. I have had a couple built for me there and they are great. I run a HV Pump and have sheered the roll pin on a Mallory before. Ignition Engeneering can fix you up with one you will love. You can find the info on the net just Google it. JMO
 
OP
OP
7

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
72Sport You can give Ignition Engeneering a call to get a great Distributor. Since you are in So Cal it is not far away. I have had a couple built for me there and they are great. I run a HV Pump and have sheered the roll pin on a Mallory before. Ignition Engeneering can fix you up with one you will love. You can find the info on the net just Google it. JMO

Just talked to Ignition Engineering. Sounds like he does all the right stuff to improve the performance of the stock distributor. I will dropping off a distributor in the morning.

Thanks for the input.
 
OP
OP
7

72Sport

Bronco Guru
Joined
Jul 8, 2002
Messages
2,954
I called the PerTronix tech line earlier today to find out how they attached the gear to the distributor. I didn't want to have the same problem Ben mentioned in the second post above. The tech said they are pinned the same as stock and the gear is a sliding fit on the dist shaft. He said the biggest problem is stuff going through the oil pump. Just about anything will jam it according to him. Well I drained the oil on Sat. I have a funnel with a "very fine" screen that snaps in the small end of the funnel. I wanted to catch all the pieces of roll pin that might be in the engine. I wanted to make sure I could account for the whole roll pin.

I cleaned out the screen a little while ago. The screen was covered with what looked like strings of brown varnish. You can see in the picture what it looked like after I soaked up the oil. You guessed it lint from red shop rags I used to mop up the oil and coolant from the engine when I replaced the intake gaskets twice in the last few years. I rolled all the lint up in what you see in the pictures as I removed it from the screen.

Moral of the story do not use rags to clean anything inside the engine. The cast iron is like a wire brush and will pull lint out of just about any rag you use. I would say blow dry with compressed air or use a shop vac or both. Maybe someone out there has other ideas.

I don't know if the oil pump is locked up but I will find out in the near future. I can only guess what pick up screen on the oil pump looks like.

The same holds true for automatic transmissions. I worked on a Hydramatic in high school. A mechanic friend said don't get any shop rags near the transmission. Use compressed air to dry things off. The tail housing had a film of stuff on it. I knew a lot when I was 17. When he wasn't looking I wiped the film out of the tail housing with a shop rag. The tranny started acting up not too long after. Pulled the pan and the filter screen looked like it had a shop rag covering it. The mechanic friend just smiled as he walked by. Valve bodies and lint don't get along.
 

Attachments

  • IMG_0969.JPG
    IMG_0969.JPG
    59.2 KB · Views: 38
Top