• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

tuning an A9P computer?

Mike Matthews

New Member
Joined
Aug 9, 2010
Messages
6
Can anybody give me some advise on having my computer tuned? I have a 1977 Bronco that I put an 1993 5.0 injected engine in using a RJM harness.
The engine has alum. Edelbrock heads, z303 cam, standard bore with fordged Mahle pistons, tublar GT-40 intake, 70mm throttle body, 65mm mass air tuned to match the 24lb injectors, everything was professonally ported and is all brand new, including all new sensors. It does start and run well, but for all that is done, I feel like it should have more. The rest of the Bronco has a, C4 with 3000 stall, all B+M guts, 4.88 gears, and 35'' tires on alum weld wheels. ANY help is appricated
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Sounds like you are due for a tune.

Most dyno shops can do a tune. Super chips custom tune is a big one.
There are a couple of DIY chips. The old standby is a TwEECker and the new kid on the block is the Quarterhorse.

The DIY version can cost more then the shop tune by the time you add up software costs and a usable wide band O2 sensor.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
WOW! a 3k RPM stall with 4.88's and 35's????

I was thinking the same thing too, but I just kept with the original request and help tuning the wild ride. The actual drivability issues that will come later will be in a different thread. Since the parts are already in, wait until complaints and address then.
 

jlake4130

Full Member
Joined
Mar 14, 2011
Messages
244
Loc.
phoenix, az
I was thinking the same thing too, but I just kept with the original request and help tuning the wild ride. The actual drivability issues that will come later will be in a different thread. Since the parts are already in, wait until complaints and address then.

I dont mean to hijack but what issues will ther be with the set up he's running? i know the 4.88's are a bit high for a 35" tire (4.56 would be better) though i don't understand how the stall on the tq converter plays in? Explain please, thanks.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
The cam he's running is mostly what dictates the stall speed. Its a little on the big side for a 4x4 but his gearing and stall speed should be in line with his choice.
with bigger cams the engine doesnt make lowend torque until higher in the powerband so hence the need for a higher stall speed. While I dont know what his driving plans are I think thats a bad setup for a bronco unless your doing some type of racing.
 

barronj

Bronco Guru
Joined
Jun 6, 2009
Messages
1,859
Wow, a Z303... that's a lot of cam. If you have to leave it in, you might get a multiple indexed crank gear & advance it a few degrees to give you some bottom end back. The cam is designed for 2500-6500 (I've also read 3500-6500).

I've had the multiple keyed/indexed crank gears before, and a monkey could do it. Each key slot would have the amount of advance/retard you were effecting, ie 2,4,6 degrees.
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
A tune may help with driveablity a little, but as stated above. Its a poor cam choice for the vehicle. Before you spend $500 for a tune and chip, consider installing another cam and then do the tune...would suck to have to tune it, not be happy, install a different cam to get the right performance and then tune again...even at a slightly discounted rate--maybe--cause the shop feels bad for you...

Its all about low end to get these pigs moving.
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
I dont mean to hijack but what issues will ther be with the set up he's running? i know the 4.88's are a bit high for a 35" tire (4.56 would be better) though i don't understand how the stall on the tq converter plays in? Explain please, thanks.

that's just a high stall, and i feel he'll be winding out on the street, much less being able to get on the highway. not knowing his intent of use, i'm just questioning and not bashing.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
that's just a high stall, and i feel he'll be winding out on the street, much less being able to get on the highway. not knowing his intent of use, i'm just questioning and not bashing.

That's why I didn't go that way. Other then a bit high RPM it should actually work fairly well for some playful antics. I see the potential for fun on the street, dunes, mud, etc. Places that call for a motor to wind out a bit. So I look at the broad picture, figure he planned it for his wants and let it go. Now if he said he planned to rock crawl it, I would completely advise a differnt cam and convertor package. But was (not) stated what the plans are, it isn't proper to advise on assumptions.

As for the retune. If needed it is usually fairly cheap. You already have the hardware (chip) so it is little more then a few runs on a dyno and reprogramming what you have. Just labor, no hardware. So a shop to retune would be about half of the inital tune. It shouldn't take much as your parts are actually a fairly basic tune. No wild turbo setup or anything like that.
 

fetorino

Sr. Member
Joined
Dec 1, 2010
Messages
625
Loc.
Orange, CA
May not want to hear it but

I'd agree the cam doesn't make a lot of sense. Best bet if you have the flow numbers for your heads is to get a custom cam that matches your combo.

By combo I mean total combo includding intended use.

I would sacrifice some top end hp for some low end torque and the Bronco will be faster stoplight to stoplight and drive better. A tighter converter with the new cam would be a good idea.

That high stall is going to throw off a lot of heat so I hope you have a trans cooler. I'm sure if you spooled it up against the converter everytime you took off you would feel it accelerate better but realize just driving around the converter is slipping and will make it feel softer.

Bottom line is for a snappy feel during normal driving you have the wrong combo. JMO
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
again, making assumptions without knowing how it will be used.
With that much gear on a 35" tire it won't strain the convertor that much. Cruising speeds will be high enough that the convertor should be in a coupling phase. That is if it is even planned to be driven on the street.

He asked about getting the computer tuned, not if we think his combo of parts is correct for your driving. So does anyone else have an comments about computer tuning to help this guy?

I'd agree the cam doesn't make a lot of sense. Best bet if you have the flow numbers for your heads is to get a custom cam that matches your combo.

By combo I mean total combo includding intended use.

I would sacrifice some top end hp for some low end torque and the Bronco will be faster stoplight to stoplight and drive better. A tighter converter with the new cam would be a good idea.

That high stall is going to throw off a lot of heat so I hope you have a trans cooler. I'm sure if you spooled it up against the converter everytime you took off you would feel it accelerate better but realize just driving around the converter is slipping and will make it feel softer.

Bottom line is for a snappy feel during normal driving you have the wrong combo. JMO
 
OP
OP
M

Mike Matthews

New Member
Joined
Aug 9, 2010
Messages
6
My intended use for it is just a fun street rig. I have already done the trail and rock thing, and was looking for more of a hot rod. I understand that this cam and stall choice is not great for Bronco, but I don't have very many places to wheel aroud here anymore and figured a hot street rig would be fun.
I really appricate all the input guys!!!!!
I do have an f303 and a smaller stall on the shelf if this set up sucks.
 

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Check the Marlan Davis column (Pit Lane?) in Hot Rod Mag from 2-3 months ago - a good article on ECU tuning a Ford 347 with aftermarket parts - of course it was a Mustang and the guy was in SoCal so there were tuning shops falling all over each other trying to help him out. I think he had a bogus tune, so they swapped in a stock A9P ECU and he was much better (he was bogging, then knocking under load - so his timing map must have been Fubar'd). Most important that your MAF sensor and computer are matched. I was surprised how far the A9P box could actually adjust for the "way not stock" 347 this guy had.
 

fetorino

Sr. Member
Joined
Dec 1, 2010
Messages
625
Loc.
Orange, CA
Still say the combo will only work so well

My intended use for it is just a fun street rig. I have already done the trail and rock thing, and was looking for more of a hot rod. I understand that this cam and stall choice is not great for Bronco, but I don't have very many places to wheel aroud here anymore and figured a hot street rig would be fun.
I really appricate all the input guys!!!!!
I do have an f303 and a smaller stall on the shelf if this set up sucks.

Not terrible but not hugely impressive as a hot rod stoplight killer.

4.88 isn't that deep a gear for a 35" tire. It's really just like a 3.90 with a 28 or 29" tire (someone will get on the tire calculator program and correct me I'm sure but I think I'm close)

28 or 29" would be a tall slick for a mustang and for your motor combo to be quick in the lighter Mustang you'd be running a deeper gear than a 3.90. For a fox street rig your tire would be shorter than a 29 that's for sure.

So yea a tune can't hurt and your motor combo. It isn't a hacked missmatch, actually sounds like a good fox body mill with 4.30s. It just wants a lighter car and lower gears.

Remember your C4 also has a high first gear so that isn't getting you out of the hole quick either. I know a TKO is way deep in first and an AOD has a deeper 1st gear also.

If you want it to feel really quick besides just a tune you need a lower gear or a different cam.
 

barronj

Bronco Guru
Joined
Jun 6, 2009
Messages
1,859
I would say to make the cam swap now. You cannot swap a cam in a bronco without removing the grill (which can be a bastige on a 40 year old truck), unless you want to pluck the mill out for the job. Welcome to the site!
 

86Horn_EB_77

Jr. Member
Joined
Aug 31, 2006
Messages
100
Loc.
Austin
Just tried the Stangnet/Mustang Forums link above and it looks like it is offline - is this a common problem?

I have a 351 Lightning motor with an "unknown" (assumed stock) A9P in it - and I may need to learn all about EEC tuning (I already have a wideband O2/datalogger).

I'd be curious to hear from those who have done "on the road" tuning without a dyno - I'd like to get all the part throttle tuning done before investing in some expensive Dyno time.
 

fetorino

Sr. Member
Joined
Dec 1, 2010
Messages
625
Loc.
Orange, CA
HM I tried the link this morning and it worked

Just tried the Stangnet/Mustang Forums link above and it looks like it is offline - is this a common problem?

I have a 351 Lightning motor with an "unknown" (assumed stock) A9P in it - and I may need to learn all about EEC tuning (I already have a wideband O2/datalogger).

I'd be curious to hear from those who have done "on the road" tuning without a dyno - I'd like to get all the part throttle tuning done before investing in some expensive Dyno time.


If you are referring to the rapid share link in the page it has expired but the txt from that link is on the stangnet page.
 
Top