• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Calling all NV3550 drivers

broncojames

Sr. Member
Joined
Dec 28, 2009
Messages
391
Loc.
Smelterville ID
I plan on doing the 3550 swap next spring. I will be running 33.12.50 15s 2.5SL
and maybe a 1" BL I would like to know your thoughts and what gear ratio your running. I'm thinking 4.56 light off road mostly a daily driver

Lets hear what your running and how you like it
 

Izzy

Bronco Guru
Joined
Sep 5, 2009
Messages
2,430
Loc.
Texas
I am running the NV3550 with 33s and 4.56 gears. I went with 4.56 because I thought I might run 35s at some point. I no longer feel that way and will most probably drop back down to 4.11s.

The setup runs great though but I would highly recommend the 1" BL. It's a must. Some say you can do without but I tried that and it didn't work out so well for me.
 

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
I have a nv3550 with 4.56 gears and 35's and wish I would of went 4.88 gears. I would do around 4.33 minimum for 33's.
 

NGABronco

Contributor
Always Learning
Joined
Feb 4, 2007
Messages
7,574
Loc.
N. GA now South Carolina
The "Crazy Horse" has 3 1/2" SL & 2" BL, 35" tires and 4:56 gears. 70MPH on the interstate is about 19-2000rpm. 347 stroker engine. Around the neighbor hood it's 2nd & 3rd gear for the 35-45 mph speed limits!!;D;D
 

ttkelly

Jr. Member
Joined
Mar 7, 2010
Messages
90
It looks like I will be the odd man out. I am running a 3.5 inch lift, no body lift and the stock 3.50 gears and 31 inch tires. She does fine cruising at 70, and has plenty of get up and go... That said I would strongly recommend the body lift, I treated my self to some professional help on the instal and I am glad I did! It was not fun forcing it in with out the extra clearance.
 

76 bronco J

Bronco Guru
Joined
Oct 20, 2005
Messages
1,480
The "Crazy Horse" has 3 1/2" SL & 2" BL, 35" tires and 4:56 gears. 70MPH on the interstate is about 19-2000rpm. 347 stroker engine. Around the neighbor hood it's 2nd & 3rd gear for the 35-45 mph speed limits!!;D;D

>>> 19-2000 at 70 ??......at about :42 stacey said it's 2500 at 65mph...guess he wasn't cruisin' in overdrive...I imagine all the same stuff still on it as when you bought it, right ??....probably could use some slighty lower gears....​
[youtube]ZlTbaFx1KPU[/youtube]
 
Last edited:

NGABronco

Contributor
Always Learning
Joined
Feb 4, 2007
Messages
7,574
Loc.
N. GA now South Carolina
HaHa bronco J!!!! Thanks for posting that!!! Yeah it's still the same, no heater and the wipers do funky things!!!!! I did put the oil accumalator on it and Stacey fixed the tire carrier!!! Oh yeah, it still has about a half dozen scars from that little ride!!!!
Thanks again!!;D
 
OP
OP
B

broncojames

Sr. Member
Joined
Dec 28, 2009
Messages
391
Loc.
Smelterville ID
Something I probably should of added is that i live in the northwest in the rocky mountains if Idaho and might be moving to the flat grounds of central Missouri
down around Clinton. so there will be a big change in the terrain witch I'm sure plays a part of gear ratios
 

dbevans2249

Sr. Member
Joined
Sep 21, 2003
Messages
610
Loc.
Buena Park, Ca.
I had 4.11's with the NV3550 and 33's. I was not happy with the street or highway performance. IMO it was geared to high. It was to hard to start in 2nd on the street, first was to low to start in and it needed to go to fast in OD on the highway. I changed to 4.56's since I do not plan to go up on tire size. If I thought there was a chanse I would go to 35's I would have gone to 4.88's
 

VT_Don

Sr. Member
Joined
Aug 16, 2001
Messages
365
James, Most modern sport utility vehicles, with V8 engines are geared to deliver 1800-2000 RPM at 65 MPH in overdrive. That will typically yield good engine efficiency, drivability and minimal wear. Like you, I am set-up for the NV3550 0.78:1 overdrive, and 33" tires. I find a 3.90:1 axle ratio a good match with 2013 RPM @ 65 MPH.
If the objective is primarily off road use, then bias the axle ratio slightly lower.
 
OP
OP
B

broncojames

Sr. Member
Joined
Dec 28, 2009
Messages
391
Loc.
Smelterville ID
been a few weeks since iv been to this thread and have recently decided i will be going with a 351W and was wondering if the 3550 will hold up to it ?
 

73stallion

Bronco Guru
Joined
Mar 5, 2004
Messages
16,786
Loc.
Eugene, OR
DonsBolt has about 400 horses in front of his NV3550, it's never given him a problem. remember, they were dyno'd to hold 310hp in a 7k lb vehicle, and that was with 3.50's and 33's when they tested.
 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
I think that the 1" BL is an absolute must with the NV3550. Just makes the install alot easier and helps avoid any cutting into the floor or crossmembers.

As for gearing, I am running 4.56 gears and 35's and I think that the gearing could be a bit lower. Although it isn't bad by any means, I think with 4.88's it would be alot more responsive.

Good luck with whatever you choose. As long as you don't go crazy with the 351, it should be okay I think but that all depends on how you drive it I guess. ;D
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
I have been running a true Ford SVO GT40 351W crate engine in front of the 3550 for about 3 years now. 4.10 gears and 33s. I wouldnt change the gearing for the street, I consider it perfect. Yes you have to decide what gear to take off in. Up hill-1st. Down hill starts-2nd. Flat ground depends on how much you like to replace clutches. I personally usually use first.

3rd will pull from 25 mph to 70 in a matter of seconds.

4th will pull any hill on any hiway I have been on at 55.

After that the 351 will pull a 6 % grade in 5th at 60 no problem.
I live in Eastern Washington so I know what a hill is.

If you want to off road than You might want lower axel gears but on road I am plenty low. It will pull any hill around in OD so why would you want 4.56s.
 

broncoitis

Bronco Guru
Joined
Jul 23, 2010
Messages
4,449
I think you are right on with the 351W but that is a whole different animal compared to a 302. More torque and horsepower I would beleive especially if you are running a GT40 Crate engine. Definitely must be FUN to drive!!!! ;D
 
OP
OP
B

broncojames

Sr. Member
Joined
Dec 28, 2009
Messages
391
Loc.
Smelterville ID
I have been running a true Ford SVO GT40 351W crate engine in front of the 3550 for about 3 years now. 4.10 gears and 33s. I wouldnt change the gearing for the street, I consider it perfect. Yes you have to decide what gear to take off in. Up hill-1st. Down hill starts-2nd. Flat ground depends on how much you like to replace clutches. I personally usually use first.

3rd will pull from 25 mph to 70 in a matter of seconds.

4th will pull any hill on any hiway I have been on at 55.

After that the 351 will pull a 6 % grade in 5th at 60 no problem.
I live in Eastern Washington so I know what a hill is.

If you want to off road than You might want lower axel gears but on road I am plenty low. It will pull any hill around in OD so why would you want 4.56s.

as if 2 months ago iv completed the rebuild of front and rear with 4.56 33/12.5/15s so guess I'm stuck with them. I am still running original 302 and 3 on tree 2.5" S.L . power steering and brake upgrade. now just saving for all the rest.

What part of NW WA. you from ? I'm just out side of Kellogg Idaho.
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
All this talk about starting out in 2nd gear because 1st is too low is just plain weird. You just do a short shift and take the load off the clutch a little. I have 4.11s and 30s for pete's sake and it doesn't seem too low to me. The moral of the story is that the NV 3550 is pretty versatile, plenty stout, and just plain nice.
 
Top