• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Locker on front or rear?????

G's Baja Bronco

Bronco Guru
Joined
Aug 7, 2010
Messages
1,362
Loc.
Sunny SO CAL
as it sits my 75 EB has no lockers/posi on front or back, the rear is a big bearing 28 spline 9" and the front is the Dana 44, I was looking at the Aussie locker and they do not make one for the rear 28 spline, but do for the front.
I have always had stock LS's on my stangs and on my Ramcharger, so I like the feel.

I am looking for a stock LS 28 spline for my rear, but at around $250 I can trow a Aussie on the front, I really only do desert, meaning sand, loose dirt and some small amounts of mud. I figure most of the time I will have the front unlocked and only off road will I lock it. does this sound like a good combo, or should I save my money and go rear locker and 31 spline shafts?:)
 

fungus

Bronco Guru
Joined
May 27, 2009
Messages
1,548
Loc.
Kaneohe Bay, Oahu
I was in the same boat as you with my '69, open/ open. I sourced a nice used Detroit for the rear for $200 from a fellow EB'er and upgraded to 31 spline axles at the same time & LOVE it! Made a huge difference offroad. I still wanted a little more so I opted for the Aussie locker up front. I got a set of chomo shafts & larger U joints for the front end and have the Aussie setup in a carrier but not installed yet. That's the next project once I do the 5.0 swap in the next couple months!
 

Buldozer

Bronco Virtuoso
Joined
Oct 17, 2007
Messages
3,066
Loc.
God's Country
31 spline is a must unless you want to break shafts. stock shafts break when locked IMO.;) Locker and 31 splines go together.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
For only sand, loose dirt, and mud, I'd just put in a good rear posi and leave the front open. Yukon sells a strong one.
 
OP
OP
G's Baja Bronco

G's Baja Bronco

Bronco Guru
Joined
Aug 7, 2010
Messages
1,362
Loc.
Sunny SO CAL
thanks guys,

Blubuckaroo do you mean for the 28 splines? and is yes, is it a mini or do I have to change the carrier and reset the gears??:?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
You can usually pic up used 28 spline LS units for les than $200 heck most of the time you can get a whole center section gears and all for less than that but you might need to rebuild the LS unit. a new clutch pack cost about $60. Just be aware that the stock LS unit is not very strong and can easily be broken I've broken 2 one with 31 in tires and 2 much gas pedal on the street and the other with 33in tires idling up a hill. Any unit you intall in the rear will require resetting the gears good part is the 9in is super easy to setup
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
31 spline is a must unless you want to break shafts. stock shafts break when locked IMO.;) Locker and 31 splines go together.

X2.......... next he gonna say ARB then RCV.

Btw you CANNOT get a 31 spline mini spool and use it in a 28 spline carrier, 31 sline axles will not clear the carrier bearings. I tried it!....just a heads up. Put your money in the rear then upgrade front as you go.
 

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
Locker in the front is the best bang for buck. Locked front end will pull you through obstacles. If you break something due to the locked front end, simply disengage the front axle and you're still road worthy to limp home. Break an axle in the rear and you don't get off the trail until fixed. Only downside of front locker is snow performance where you want the proper slip of an open style diff. But hey, where you live snow performance is likely null...
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Locker in the front is the best bang for buck...

I am going to completely disagree with that. The last Bronco I ended up twin sticking with lockers at both ends. I drove in all kinds of configurations, front only, rear only, high range, low range. Use of a front locker had the least improvment of anything. I could usually get further in 2WD with a locker in the rear. A front locker is the finishing touch, not the first step.
 
OP
OP
G's Baja Bronco

G's Baja Bronco

Bronco Guru
Joined
Aug 7, 2010
Messages
1,362
Loc.
Sunny SO CAL
HUMMMM. sunds like I will do the rear first, my old Ramcharger with just the stock LS on the dana 60 and 37" m/ts is what I used 95% of the time, I only engaged the front locks and used 4 low for crawling up steep hills with the trailer to avoid wheel spin.

I think I will invest in a complete 3rd member and 31 spline shafts. for now it will be open to work out a crap load of small items, I really would like to run 35" m/ts, and my 4.10's with the AOD are not desirable, maybe 4.56's or 4.88's.

will I have to change the front carrier to go with 4.56 or 4.88's from my 4.10 carrier on the dana 44?

Thank you all, I love leveraging all this knowledge, hopefully learn from others!
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
No its 3.92 and up, your 4.10 carrier will be good.

And your thinkin right if you dont have all the tools and bearing kits just as well to buy a full 3rd...I did it that way add it up youll see.

Make sure what axle housing you have before you order your shafts, SB BB?
 

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
I am going to completely disagree with that. The last Bronco I ended up twin sticking with lockers at both ends. I drove in all kinds of configurations, front only, rear only, high range, low range. Use of a front locker had the least improvment of anything. I could usually get further in 2WD with a locker in the rear. A front locker is the finishing touch, not the first step.

same here, when i blew out my front i was amazed at the places i went with just the rear spool
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
And if your going to all that expense of new carrier and axles and find out you have small bearing rear, do replace the housing ends to accept large bearings. 31 spline small bearing axles are no stronger in the most critical load bearing area of the axle. I broke 2 small bearing axles between the wheel flange and bearing. Here it carries the weight of the Bronco AND rotational torque. The rest of the axle just sees torque.
 

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
I am going to completely disagree with that. The last Bronco I ended up twin sticking with lockers at both ends. I drove in all kinds of configurations, front only, rear only, high range, low range. Use of a front locker had the least improvment of anything. I could usually get further in 2WD with a locker in the rear. A front locker is the finishing touch, not the first step.
I said bang for the buck!

Let’s face it to upgrade the rear you need to maintain drivability (street driven rig) and dependability so you don’t break and get stranded on the trail. To do that you need a 1k locker, something with decent street performance & superior off road performance (selectable locker or quality LSD, etc). Then of course to ensure you don’t snap shafts you need to upgrade to larger spline and/or stronger material such as cromo. All said and done and you got 2k+ in your rear end and locker setup.

The front however can be very easily upgraded with a simple and cheap lunch box locker. Let's face it the front axle remains stationary and disengaged 80% of the time anyway with a street legal rig. Front Dana-44’s are relatively strong in stock form and worst case if you do break something, it ruins your day of wheeling instead of leaving you stranded in the bush needing both field recovery and a tow home. You might have $500-600 bucks in a front lunch box locker all said and done.
 
Top