• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Locker on front or rear?????

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
I said bang for the buck!

Let’s face it to upgrade the rear you need to maintain drivability (street driven rig) and dependability so you don’t break and get stranded on the trail. To do that you need a 1k locker, something with decent street performance & superior off road performance (selectable locker or quality LSD, etc). Then of course to ensure you don’t snap shafts you need to upgrade to larger spline and/or stronger material such as cromo. All said and done and you got 2k+ in your rear end and locker setup.

The front however can be very easily upgraded with a simple and cheap lunch box locker. Let's face it the front axle remains stationary and disengaged 80% of the time anyway with a street legal rig. Front Dana-44’s are relatively strong in stock form and worst case if you do break something, it ruins your day of wheeling instead of leaving you stranded in the bush needing both field recovery and a tow home. You might have $500-600 bucks in a front lunch box locker all said and done.

Griz and Detroits run fine in the rear? if its steering the front you prolly need stiffer front shocks......only issue is if you live in ice snow land then yea go with the ARB's.
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
And if your going to all that expense of new carrier and axles and find out you have small bearing rear, do replace the housing ends to accept large bearings. 31 spline small bearing axles are no stronger in the most critical load bearing area of the axle. I broke 2 small bearing axles between the wheel flange and bearing. Here it carries the weight of the Bronco AND rotational torque. The rest of the axle just sees torque.

I have not broken a Moser yet....And aint from lack a trying.
 

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
Griz and Detroits run fine in the rear? if its steering the front you prolly need stiffer front shocks......only issue is if you live in ice snow land then yea go with the ARB's.
Auto lockers on the street down right suck - all that popping and banging... Granted if your rig sees more trail then street and the asphalt is only used to get to the trail head then auto locker is perfectly reasonable. But running an auto locker on the rear with daily driving is terrible. Those highway on/off ramps are down right scary with an auto-locker (think steering by throttle & locker engagement).
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
Auto lockers on the street down right suck - all that popping and banging... Granted if your rig sees more trail then street and the asphalt is only used to get to the trail head then auto locker is perfectly reasonable. But running an auto locker on the rear with daily driving is terrible. Those highway on/off ramps are down right scary with an auto-locker (think steering by throttle & locker engagement).

I dont have those issues. My Griz has popped once since being installed and my Tacoma with a LS rear chrips more tire than the Bronco.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
I did the locker in the front first when I was open/open. I needed to do a re gear, so locking the rear first would mean getting into the front diff also. I didn't want put a locker in my 28 spline, 3.50 rear. I didn't have the funds to do everything at once. I put the Aussie up front along with some chromo shafts, It made a huge difference out on the trail, and these obstacles are ones I've done or attempted several times with an open carrier. Now I've just done the rear with a 31 spline Detroit and 4.56 gears. My plan was to do this just once, so the 31 spline axles and a Nodular case was part of it. I've never wheeled with a rear locker, so I can't say which would be better. Big Bear in June will be my first legit test being locked F&R with much improved gearing.
Mark
 
OP
OP
G's Baja Bronco

G's Baja Bronco

Bronco Guru
Joined
Aug 7, 2010
Messages
1,362
Loc.
Sunny SO CAL
guys, I have astock dana 44 front axle, how many splines? sounds like it should be 30. I am runing 4:10 gears, if I decide to go to 4.56's will I need to change the front carrier?

if not, $250 for the front Aussie sounds like the best bang for the buck. I had opens on my 2002 wrangler and I only had 2 issues with it, super loose sand traction, 31 bfg all terrains and 6 banger with bad gearing ( I went up from 30" tires). I think my bronco with the 33 12.5's, 4.10's and cobra 5.0 (4rwd AOD) will do better with opens and locking the front now will be extra traction. Later I can do the whole dance with the rear, once I have finished about 3k more of finish work (paint and tires and ....). I figure I can droop 1-2k on it next year and do the rear and gears, to support 35" tires.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Auto lockers on the street down right suck - all that popping and banging... Granted if your rig sees more trail then street and the asphalt is only used to get to the trail head then auto locker is perfectly reasonable. But running an auto locker on the rear with daily driving is terrible. Those highway on/off ramps are down right scary with an auto-locker (think steering by throttle & locker engagement).

I don't have those issues either. Detroit in the rear, most of the time you don't realize its there, for the rest of the time you get used to it and drive accordingly.
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
guys, I have astock dana 44 front axle, how many splines? sounds like it should be 30. I am runing 4:10 gears, if I decide to go to 4.56's will I need to change the front carrier?

if not, $250 for the front Aussie sounds like the best bang for the buck. I had opens on my 2002 wrangler and I only had 2 issues with it, super loose sand traction, 31 bfg all terrains and 6 banger with bad gearing ( I went up from 30" tires). I think my bronco with the 33 12.5's, 4.10's and cobra 5.0 (4rwd AOD) will do better with opens and locking the front now will be extra traction. Later I can do the whole dance with the rear, once I have finished about 3k more of finish work (paint and tires and ....). I figure I can droop 1-2k on it next year and do the rear and gears, to support 35" tires.

No carriers are 3.92 and up no need to change
 
OP
OP
G's Baja Bronco

G's Baja Bronco

Bronco Guru
Joined
Aug 7, 2010
Messages
1,362
Loc.
Sunny SO CAL
is a track loc what ford put on my Mustangs?? 85 5.0, 87 5.0, 95 5.0, 01 4.6? how is that for desert wheeling? I found a rear 31 spline one new for $300.:cool:
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
is a track loc what ford put on my Mustangs?? 85 5.0, 87 5.0, 95 5.0, 01 4.6? how is that for desert wheeling? I found a rear 31 spline one new for $300.:cool:

That is for an 8.8" axle.
Won't work in a 9" axle.

For how good they are, slightly better then open but nowhere near as good as locked.
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
I have not broken a Moser yet....And ain't from lack a trying.

The axles I broke were stock EB axles. When they break at the bearing you loose your tire and wheel then go completely out of control.
If buying new axles anyway to go up to 31 spline why not go all the way and upgrade the $20 a piece Axel ends.

Oh yea, and X2 on the Tru Tracks. As in I have them front and rear. My rig is a 50/50 rig. For hard core off road you will want full locker or selectible.
I have never considered trading out the Tru tracks since I had them installed 10 years ago.
 

gambling209

Full Member
Joined
Apr 20, 2010
Messages
198
is a track loc what ford put on my Mustangs?? 85 5.0, 87 5.0, 95 5.0, 01 4.6? how is that for desert wheeling? I found a rear 31 spline one new for $300.:cool:

is the same style of carrier. but mustang is and 8.8 rear. my only prob with some sort of traction carrier in front was it would plow when trying to turn. i also ran 28 spline stock axles for years and never broke anything. but i wasn't rock crawling like you see on here. detroit also makes a few diff lockers. some are more street freindly than others.
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
The axles I broke were stock EB axles. When they break at the bearing you loose your tire and wheel then go completely out of control.
If buying new axles anyway to go up to 31 spline why not go all the way and upgrade the $20 a piece Axel ends.

Oh yea, and X2 on the Tru Tracks. As in I have them front and rear. My rig is a 50/50 rig. For hard core off road you will want full locker or selectible.
I have never considered trading out the Tru tracks since I had them installed 10 years ago.

was right before OCBR had to get it done. And the axles were 30 mins away
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
The axles I broke were stock EB axles. When they break at the bearing you loose your tire and wheel then go completely out of control.
If buying new axles anyway to go up to 31 spline why not go all the way and upgrade the $20 a piece Axel ends.

A little misleading for someone who may be searching this.....there will be brake issues to deal with, cost will be considerably more than $20 per side.
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
A little misleading for someone who may be searching this.....there will be brake issues to deal with, cost will be considerably more than $20 per side.

Yes, there are more issues to deal with since he allready has disc brakes but not really. Explorer brakes are supose to bolt to the 75 big bearing Torino style ends. I'm sure currie or someone is selling these. They will be more$ than the $20 junk yard ends for drum brakes. And the rear will need chucked up in a lathe to turn the old ones off so there will be a bill at the machine shop.
 
Top