• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear 9" Drum Assembly

OP
OP
ILikeBond

ILikeBond

Sr. Member
Joined
Jan 27, 2009
Messages
908
One of the things you forgot to note is there is suppose to be grease applied to the backing plate where the shoes rub. the adjuster screws should be disassembled and the threads greased and grease applied under the cap. Grease was factory applied where 2 pieces are assembled like the pivots for the parking brake. under the spring cups where they go up against the shoes. under the brake apreader bars and the wheel cylinder pins where they push against the shoes.
The factory used a grease called lubriplate. Use eithor this stuff or marine wheel bearing grease will do. Failure to grease these parts causes rust and wear on the backing plates. Without grease the brakes will also tend to pull and grab untill the brakes get fully loaded causing the Bronco dip and dive action when you first apply the brakes.

You are doing great keep up the good work. All the years on this site no one has tackled writing up this stuff Good For You!

Appreciate that advice. Since it looks like I'll be dis- and re-assembling anyway, I'll be sure to do this. I was a little amazed that there weren't simple instructions for doing this yet, either, but maybe its one of those things where simple enough for most people that no one has really thought about it. Sadly, I am on the novice side of things, so a "dummies guide" for these types of tasks is helpful for me, for sure.
 
OP
OP
ILikeBond

ILikeBond

Sr. Member
Joined
Jan 27, 2009
Messages
908
No chance. Do it right for safety and shoe life. It's easier if the backing plate is bolted to the axle.

Yep. What's a couple more hours in a long build afterall. Thanks for pointing this out and the advice, Viperwolf. Would rather have to re-do now than find out later I screwed up.
 

DuctTape

Bronco Guru
Joined
Jun 20, 2008
Messages
1,148
Loc.
Bozeman, MT
So here's the finished product, left and right. What do you think, did I do everything right?

Hope this will be helpful to someone at some point. :cool:

View attachment 277609

Bond/Jack

If the left one in this image is driver's side then these are same as mine, but I'm not expert enough to tell from the backing plates which one is drivers and which one is passenger's.

And... I'd take viper's tech advice over mine any day. ;)
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
Alot of them diagrams are on the JBG website under support, then document archives, then 66-77 diagrams.

I go there daily!

Or the LMC catalogue is good for exploding all the bronco subassemblies as well.
 
OP
OP
ILikeBond

ILikeBond

Sr. Member
Joined
Jan 27, 2009
Messages
908
Well, just to close the loop on this, I finally got around to fixing these today. In addition to correcting the shoes, I greased all the contact parts as Rustytruck suggested (and used anti-seize on the adjuster threads), and set up the parking brake as several suggested. Here are a few pictures of the process and finished product. Hopefully I've got it right this time...

Special thanks to ViperWolf who pointed out the problem with the shoes and provided the Haynes scan.

IMG_2023.jpg IMG_2011.jpg IMG_2020.jpg IMG_2025.jpg IMG_2028.jpg IMG_2032.jpg IMG_2033.jpg IMG_2034.jpg

Finished product. I think (and certainly hope) this is right, but once again, if you see anything off, please let me know.

IMG_2043.jpg IMG_2064.jpg
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
Looks right. but can you hook up the E-brake cables with all that assembled?

You read my mind. I don't think they can be installed with everything together like that. They turned out great and look correct to me. Good job!

Parking brake cable can installed after everything is together. I had mine on the road all summer and then dicided to hook up my parking brake cable. Is simple to do. Just fish the cable through the backing plate and hook up. Dont have to take anything off except the drum!
 
OP
OP
ILikeBond

ILikeBond

Sr. Member
Joined
Jan 27, 2009
Messages
908
Parking brake cable can installed after everything is together. I had mine on the road all summer and then dicided to hook up my parking brake cable. Is simple to do. Just fish the cable through the backing plate and hook up. Dont have to take anything off except the drum!

Agreed, it wouldn't be too hard. On the other hand, it was also a bit easier to do without most the stuff in the way.
 
Top