1973 Bronco for sale.
U15 wagon style with half cab top.
Half cab has been modified with a sliding window in the back.
Bulkhead is aftermarket -- it goes straight down into the bed from the half cab instead of angling in like a factory bulkhead. This gives you about a foot of storage room behind the seats in the cab.
Groovy wooden dash overlay
Bronco II high back seats
Three gas tanks -- one main, two side tanks. All three are metal tanks
Rear traction bars
Rear 9" (small bearing) with recently rebuilt third member (open carrier with 3.50 gears)
Front Dana 44 with disc brakes -- Ford knuckles out conversion
302 V8 with Edelbrock performer intake & Carter 4bbl carb
Flow Kooler water pump
Power steering with Saginaw pump
Mickey Thompson aluminum valve covers
Stock three speed transmission with Hurst floor shift conversion
Smooth shift collar on steering column
Aftermarket temperature, oil pressure, and battery gauges (need to be hooked up)
Entire Bronco has been re-wired at some point
Electric fuel pump
BC Broncos two into one exhaust system
Dual shocks in front
2" suspension lift & 1" body lift
Known issues:
Brakes need to be bled
Driver door is very difficult to open from the outside
Gas gauge does not work
Side tanks can't be used due to broken switching valve
Tunnel cover needs to be installed
Front floor pans are rusty and will need to be replaced at some point
Tailgate has rust bubbling at the bottom below the license plate
Battery hold down needs to be installed
Air cleaner needs to be installed
Rear fuel filter needs to be relocated
Front transfer case yoke is incorrect, so front driveshaft is not installed
I am in the process of addressing some of these issues. As they are taken care of, they will be deleted from the "to do" list.
Note that while in good running condition and fairly rust free (see comment on floor pans above) this Bronco has been taken off road significantly, and because of that, several of the panels are dented. Over the years, they have been smoothed out in places with body filler, but some of that filler has cracked out, and other damage has been done on other wheeling trips. This is a Bronco that was used for what it was built for, and is in corresponding condition.
U15 wagon style with half cab top.
Half cab has been modified with a sliding window in the back.
Bulkhead is aftermarket -- it goes straight down into the bed from the half cab instead of angling in like a factory bulkhead. This gives you about a foot of storage room behind the seats in the cab.
Groovy wooden dash overlay
Bronco II high back seats
Three gas tanks -- one main, two side tanks. All three are metal tanks
Rear traction bars
Rear 9" (small bearing) with recently rebuilt third member (open carrier with 3.50 gears)
Front Dana 44 with disc brakes -- Ford knuckles out conversion
302 V8 with Edelbrock performer intake & Carter 4bbl carb
Flow Kooler water pump
Power steering with Saginaw pump
Mickey Thompson aluminum valve covers
Stock three speed transmission with Hurst floor shift conversion
Smooth shift collar on steering column
Aftermarket temperature, oil pressure, and battery gauges (need to be hooked up)
Entire Bronco has been re-wired at some point
Electric fuel pump
BC Broncos two into one exhaust system
Dual shocks in front
2" suspension lift & 1" body lift
Known issues:
Brakes need to be bled
Driver door is very difficult to open from the outside
Gas gauge does not work
Side tanks can't be used due to broken switching valve
Tunnel cover needs to be installed
Front floor pans are rusty and will need to be replaced at some point
Tailgate has rust bubbling at the bottom below the license plate
Battery hold down needs to be installed
Air cleaner needs to be installed
Rear fuel filter needs to be relocated
Front transfer case yoke is incorrect, so front driveshaft is not installed
I am in the process of addressing some of these issues. As they are taken care of, they will be deleted from the "to do" list.
Note that while in good running condition and fairly rust free (see comment on floor pans above) this Bronco has been taken off road significantly, and because of that, several of the panels are dented. Over the years, they have been smoothed out in places with body filler, but some of that filler has cracked out, and other damage has been done on other wheeling trips. This is a Bronco that was used for what it was built for, and is in corresponding condition.
Last edited:











