• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Any TIG welders out there?

Broncofan76

Sr. Member
Joined
Jul 2, 2010
Messages
432
Loc.
Atlanta
I finally bought a diversion 180 and have been welding a cart for my MIG and TIG machines (with a spot for a plasma one day). I built the cart both because I need a proper cart and also to see if i can get the hang of a TIG machine prior to working on a real project that actually matters. Things are going "okay" and when I mess up I generally know why and that's my goal.
I wondered if anyone had suggestions on what size tungston or type/size filler rod I'd use for 1/8" mild steel end caps. I've been using I have the 2x2 and 1.5x1.5" tubes cut on a 45 and I need to put some caps on em. These welds will be very visible and I'd like to get em right and not have to grind em off or down to make em presentable. any tips?
I've been using 3/32" ER7OS-2 rod and 3/32" Tungsten Electrodes

TIA
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
I have an old machine but this is what I use. 3/32 lanthanated tungsten electrode and I use the same filler rod that you have. When you say 3/32 tungsten which one is it? What color is the band on the end? If it is green it is pure tungsten , if it is orange it is thoriated , if it is grey it is lanthanated.
 
OP
OP
Broncofan76

Broncofan76

Sr. Member
Joined
Jul 2, 2010
Messages
432
Loc.
Atlanta
I know the one that came with the machine has a grey band. The ones I bought superstitious have a blue? Band on top. I can confirm tomorrow. If I'm not mistaken I think I was putting down nicer beads with the grey one.
 

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
Here is a quick color code. My recomendation is 3/32 2% thoriated electrodes. We use 1.5% lanthanated at work and it is ok..... just don't get it above 170 amps or it doesn't live very long. Diamond Ground also has an electrode they call "tri mix" and I have used it in the past and liked it. Pay close attention to the way you grind your tungsten. You want to grind it so the grind marks run parallel to the tungsten with a slightly blunted end. If you grind it so the grind marks run circumventually (is that even a word?) up the electrode the arc can swirl on the way to the work piece. Also, make sure you use a dedicated grinder for your tungsten. If you use the grinder for other work you can actually smear the embedded material from the wheel into your electrode. Your wire size and type will work good. Just remember, if you want good looking welds: practice, practice, practice. Oh, yea, for street cred: I weld on nuclear piping to pay for Bronco parts. ;D
 

Attachments

  • tungsten.jpg
    tungsten.jpg
    110.1 KB · Views: 219

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
It just sound impressive. Welding is welding, just a whole lot more paperwork!!
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
I have welded a lot of things, but nuclear piping! You the man!
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
I've been TIGgin for 7 yrs and I learn something new everyday. So what 67 half cab said sounds like some good stuff to try. I tend to spend a lot of time preparing my piece that I'm going weld. Removing scale, using SS wire brush and then Wiping down with Iso alcohol give me some really nice welds bc the surface is clean. I use that same practice for MIGging as well. Its possible to weld a poor surface together but the weld can be full of impurities and therefor may not be as strong. May look good but looks can be deceiving. Also never use a wire wheel on your material you are about to weld bc it may embed oil and other impurities, sand paper can do the same thing. These are things to consider when certifying tubes.
My street cred: Aircraft Machinist/ welder for Air National Guard
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
My diversion crapped out after 5 years but it has paid of itself a long time ago. With the price of argon and tri-mix gas going up, I've learn to use the mig on most steel projects, and use the diversion on TIG duties of stainless and aluminum. I tend to stick to one size tip 3/32" and I believe it is gray color band.
I recently purchased a Dynasty200 and have yet to set it up.
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
we use red tungsten and either normal filler rod or sometimes SS filler rod. Don't know the numbers off hand. Just buy whatever the local welding shop hands us. It don't really matter what rod you use for mild steal.

We use the same red tip tungsten for welding everything....steel, stainless, galvanized, aluminum. It don't much matter.

Its not the rod or the tungsten its you! You should be able to get a perfect weld everytime with any combo of rod or tip. If its getting pinholes sometimes its contaminated and no mtter what you do you just keep pushing the contamination around. Sometimes at that point I grab the Stainles filler rod and for some chemical reason the SS rod will push the contamination out of the weld.

Oh and another thing I will say is that I usually never prep any surface. I just grab the welder and start burning. If its greasy sure wipe it off but if its rusty or even painted the tig will burn off the rust or pain. Just pedal it slightly and watch the paint burn off, then back up and start welding. I welded my whole roll cage so far and never cleaned anything off any of the tubes or plates.

Sometimes the electrode end will get balled up and start heating poorly. In that case take the tungsten to the grinder. After you get a new sharp point it will weld 100% better.

Sounds like the tungsten and filler rod you are using is exactly what we been using for the last 10 years. And we weld everything from cast exhaust manifolds to axles to frames to popcans with it. Whats more important to me is the size of the filler rod. Too small and you cant keep up-sometimes ill take two rods and twist them together or hold them together. We did that with our stainless rods for a while but last trip to get gas we picked up a tube of much larger SS fill rod.

Step away from the project if your welds get crappy....sharpen your tungsten....and go back at it slowly. You should never have to grind your welds!
 
Last edited:

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
we use red tungsten and either normal filler rod or sometimes SS filler rod. Don't know the numbers off hand. Just buy whatever the local welding shop hands us. It don't really matter what rod you use for mild steal.

We use the same red tip tungsten for welding everything....steel, stainless, galvanized, aluminum. It don't much matter.

Its not the rod or the tungsten its you! You should be able to get a perfect weld everytime with any combo of rod or tip. If its getting pinholes sometimes its contaminated and no mtter what you do you just keep pushing the contamination around. Sometimes at that point I grab the Stainles filler rod and for some chemical reason the SS rod will push the contamination out of the weld.

Oh and another thing I will say is that I usually never prep any surface. I just grab the welder and start burning. If its greasy sure wipe it off but if its rusty or even painted the tig will burn off the rust or pain. Just pedal it slightly and watch the paint burn off, then back up and start welding. I welded my whole roll cage so far and never cleaned anything off any of the tubes or plates.

Sometimes the electrode end will get balled up and start heating poorly. In that case take the tungsten to the grinder. After you get a new sharp point it will weld 100% better.

Sounds like the tungsten and filler rod you are using is exactly what we been using for the last 10 years. And we weld everything from cast exhaust manifolds to axles to frames to popcans with it. Whats more important to me is the size of the filler rod. Too small and you cant keep up-sometimes ill take two rods and twist them together or hold them together. We did that with our stainless rods for a while but last trip to get gas we picked up a tube of much larger SS fill rod.

Step away from the project if your welds get crappy....sharpen your tungsten....and go back at it slowly. You should never have to grind your welds!

You should never weld on galvanized metals. Grind the coating off first. Welding on the galvanized (zinc) coating can cause metal fume fever. Check out the symptoms.....something you don't want to experience.

When GTAW (tig) or GMAW (wirefeed) it is critical to clean off all foreign materials (grease, oil, rust, mill scale). There is no flux on the welding wire to remove the contaminants from your weld puddle. You are not going to "burn" off the crap with your weld arc, it is going to leave bad stuff behind.

Welding is like anything else out there. The final product is only as good as your prep. If it were me and my family protected by a roll cage I built, I would make sure I did everything in my power to make the strongest welds possible!
 

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
Sorry I dont really TIG but if there is one thing you alwasy do whether it be MIG or TIG is you clean the surface-- if I were building a gate, cattle fence or something I was going strickly for speed I wouldnt clean it. Automotive in my opinion should be held to a higher standard-- thats just me though. The cleaner the material the less spatter you have and less clean up. I will however agree-- some days your welds are just gonna be off-- you drank too much coffee, the old lady pissing you off or its just not your day-- stop welding unless you wanna grind out the welds and re-do it. About a week ago it was the end of the day and after the 4th f-up weld-- I ground out the weld, shut up shop and in the morning laid down a bead that anyone would be proud of. Sometimes it better to know when you are beat :)
 

broncojo

Full Member
Joined
Jun 25, 2013
Messages
341
Loc.
Lewis Run, PA
Have to agree with 67 Halfcab, prepping is just important as putting down the weld. I personally use acetone to wipe down the weld area and flapwheels to clean any dirty metal. 3/32 thoriated with 1/16 er70 rod is what I typically use unless I'm getting into something heavier than 1/4". Here are a couple of pics of my long arms I'm building for my trail rig at the moment. http://s1178.photobucket.com/user/bogatah/media/68 BRONCO/DSC01811.jpg.html?sort=3&o=0
http://s1178.photobucket.com/user/bogatah/media/68 BRONCO/DSC01809.jpg.html?sort=3&o=1
I think they are pretty decent anyway.
 

BroncKrawler

Sr. Member
Joined
Dec 3, 2006
Messages
802
Loc.
Harrisburg, Oregon
I was an industrial pipe welder for 6 years and only welded stainless with scratch arc TIG. I use solely 1/8" 2% thoriated Tungsten (red band), but have used 3/32" 2% thoriated on smaller projects. I keep a good amount of 3/32" and 1/8" ER70S carbon rod on hand at all times at home for my bronco welding projects. I've used all sort of different torches and have found the Radnor flexhead torches work the best for me (besides the push on grip...) If you get more technical and practice walking the cup I would suggest learning with a size 8 cup, walk wide and fast!

bknbronco, your advice is horrible.... always prep your surface, wipe it with acetone and remove any dirt or paint with a grinding disc or flapper wheel, etc. TIG, just like every other type of welding needs a CLEAN welding surface to obtain the best weld possible / penetration.
If you're welding on Aluminum use pure tungsten (green band), ball the tip using a piece of copper and switching your polarity to DC+ then go to AC with hi-freq. If you don't know the names of your welding rods you should probably start learning more about the craft of welding instead of giving advice on it.
 
Last edited:

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
Sometimes it better to know when you are beat :)
Well said!

Im not saying that you should in any way shape or form do what I do! I have never taken a welding class nor have a read a book on it or watched a movie about it. I grabd ahold of the torch on a Lincoln 185 one day and welded together a 6'X16' crankdown trailer for my fish house. That was the first thing I have ever welded and is what I learned on. The fish house trailer has a few thousand miles on it in the last 5 years and is holding up just fine. If there is a lot of rust I flap wheel or wire wheel it for sure. But if its new metal I just weld away usually. If its painted I might use the small belt sander real quick but a lot of the times ill just burn the paint away with the tourch.

And I know your not supposed to weld on galvanized but I have welded a lot of fence pipe and such. I just hold my breath.;)
 

lowbush

Bronco Guru
Joined
Sep 13, 2010
Messages
1,807
Loc.
Summerland Key, FL
Miller has an app for the iPhone and Android that is free and is a great resource for the different combinations of consumables. You just plug in the type of metal and the thickness and it gives you the rest of the parameters. If you do any welding it is a great resource to have.
 
OP
OP
Broncofan76

Broncofan76

Sr. Member
Joined
Jul 2, 2010
Messages
432
Loc.
Atlanta
WOW - thanks for the insight guys. I've been practicing more and things are coming together for me now.
-I'm pretty meticulous about cleaning the work surface and prepping everything. I'm not trying to play with the amps and flow a little to get the right combo.
-I also wondered what welding with a different torch might be like (not that I'm "too good" for the one it came with or anything jut thinking it might be easier to maneuver? I was considering the WP-9. My current project usses 1/8" square tubing so I dont need a ton of amps and that torch seems well reviewed. I find myself fighting with this one a bit to flex it into corners and angles etc)
-I ordered some new rod (more of the same) and new tungsten also. I understand that I need a dedicated grinder for the tungsten. Can I use one wheel on my bench grinder for tungsten and the other for metal? (it has 2 6" wheels spinning at once) or is that too close and will contaminate the electrode?
thanks guys. this is great info.
 

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
Yup, just use the one wheel for your tungsten. It's not the grinding grit comming off the other wheel you are woried about, but the materials embedded into the wheel itself.
 

Crawdad

Bronco Guru
Joined
Feb 16, 2011
Messages
3,635
You would be surprised of all the contaminants in a grinding wheel. I get on to Airman for grinding aluminum on grinding wheels. Abrasive cop saw aren't good to cut aluminum either. It too can get in the abrasive blade and transfer in steel when cutting a piece. We have a water-cooled chop saw for aluminum. We have it like that in our workplace for a reason. But at home my abrasive saw cuts everything bc I'm not welding aerospace equipment, plus I don't TIG at home.
Best way to know you are on the right track is TIG some butt-joints. Make sure you are getting penetration below the joint. Cutting a cross section of your weld, you can see the penetration there as well if you polish it up. Just bc it looks nice on top don't mean squat if you don't have the proper penetration. I've been doing this for 7 yrs and I'm decent at it, but I have a lot of catching up with the big boys! I enjoy the sound of bacon splatter on a weld table! Take some pics and we will give you some pointers.
 

lowbush

Bronco Guru
Joined
Sep 13, 2010
Messages
1,807
Loc.
Summerland Key, FL
Best way to know you are on the right track is TIG some butt-joints. Make sure you are getting penetration below the joint. Cutting a cross section of your weld, you can see the penetration there as well if you polish it up. Just bc it looks nice on top don't mean squat if you don't have the proper penetration. I've been doing this for 7 yrs and I'm decent at it, but I have a lot of catching up with the big boys! I enjoy the sound of bacon splatter on a weld table! Take some pics and we will give you some pointers.


Generally with TIG if the weld looks right it has proper penetration, the problem that you usually run into with TIG is head dispersion, when you weld with TIG you should see a rainbow coming from the weld area if it just goes from a yellow to blue real quick you may have created a brittle joint by having too high of heat. It should bloom out from the weld point in a rainbow of colors when it has been welded at proper temps. This really only matters for structural stuff like roll cages a quick way to test a structural weld like a cage is to create a V section, hook some chain to both sides, hook one side to a tree and another side to your tow hitch and then gass it, it it bends the steel you are good to go, if it breaks at the weld it was too cold and if it cracks somewhere else you have put too much heat into the weld.
 
Top