• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
behemoth,

I just noticed your window frame... I was thinking about narrowing the top rail to get more window... It looks like you have done this and rounded the corners as well.

another nice mod, I am sure it helps being able to see a bit more. Whoops that might be the one you found for sale. I now see the window frame comment.
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
As I had posted earlier, I had decided to move the notch back to accomodate moving the rear axle back 2.5". I know it was another "do over" moment, but I really like the look of the axle moved back.

The smaller notch that we can installed the first time around is shown in the background in the first pic. The larger notch kit that I had purchased is clamped to the passenger side frame rail in that same pic.

The second pic shows where we retained the old notch and added to the rear allowing it to be extended to the new location. The shock mounts had to be moved back (to retain the 30 degrees) and cut down as they were going to be too tall to fit under the stock location of the bed. Of course the panhard bar had to moved back also to stay parallel with the axle.

It is back to the media blaster again and then back to the shop to repaint the frame.

I am going to Raptor line the frame this go around, but leaving the A arms and link bars painted black. The rear axle will be painted back black also. It breaks up the color scheme a little and I think that's another improvement. Hopefully sometime very soon we will have pics of the body on the chassis and I can start mocking up the steering, brake and fuel lines. Any progress is progress, and that's a good feeling for me right now!

I had to get my frame altered "AFTER" bringing it home. The dimensions were not as specified. Then after starting, in order to get everything to work the rear end mounts had to change. It stunk... Sure is good to have that behind me. I'll need to pick up a fender soon to make sure the body is in right position before making mounts.(Should be close)
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Yeah I don't like doing things twice, but I would rather do it over then live with something that I was never satisfied with to begin with. I hope to have the new paint on the frame by weeks end, and set the body on the frame for the first time. I am pretty excited about that! ;D
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Yeah I figure I can set the engine in and mock up the steering. I could also set up the fuel tank and run the fuel/brake lines. Maybe I will get the old girl running this spring/summer!
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well I got the frame painted and Raptor lined. I have the front aseembly going back togethertonight, and tomorrow I will get the rear cleaned up and painted and back together also. I also ordered 1" wheel spacers for the front to bring it back in line with the rear axle.

I hope to have the body on the chassis by Saturday. It has been a long road but I am looking forward to seeing what the end result is starting to look like...finally! :D
 

Attachments

  • photo 1.jpg
    photo 1.jpg
    122.9 KB · Views: 81
  • photo 2.jpg
    photo 2.jpg
    104 KB · Views: 78

broncoandy

Jr. Member
Joined
Aug 29, 2013
Messages
52
Loc.
Kingsport
Don't go lower. Keep it stock or go with a little lift. I hate to see this done to our Bronco's. No body ever lowers a jeep and this ain't no jeep. Just my opinion.
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Don't go lower. Keep it stock or go with a little lift. I hate to see this done to our Bronco's. No body ever lowers a jeep and this ain't no jeep. Just my opinion.

A little late for that, these frames are already highly modified for the street. It is not even a 4x4 any more. Most doing this already have lifted Broncos...
I picked up one ready for the scrap yard, better lowered than smashed and gone for ever.

Keep going Marty looking good!


-Ed
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I didn't get enough manpower to lift the body and set it on the frame, but I did get it back together. I will be sure to post pics when I do get it on the chassis.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Warmer weather is on the way. And I have work to do! Stay tuned for updates along the way! ;D
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I got smart finally and actually made out a list so that I can keep things moving forward with this project. Work has been busy so there is "Bronco money" in my account also. As I started to list things as I would need them to have some kind of order to the chaos, I got to the stage where I would need to locate the control panel and ECU for the 4.6 DOHC engine, and realized that I had very few options when it came to placing the electronics for this project.

I then changed my mind (again) and decided to go back to the stock location for the fuel tank. This would allow me to stand the bulkhead straight up creating more space behind the seats. This seemed like the best place to place the electronics, and was highly recommended by the manufacturer. I will come back to that later...but I have a plan. :-X
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Ok. I have parts ordered. I have decided to do things the right way the first time....well sorta. I also have ordered the brake/fuel lines. I got the kit with the aluminum clips (BC Broncos) so all you have to do it tap the existing holes in your frame 3/8-16. I will be buying the Extreme PB Booster kit sometime in the near future as the next stage of work to be done.

I bought a new EFI tank from Tanks,Inc. (I can't believe that I missed this when looking for a tank awhile back!) It is a 15 gallon tank, and it fits well with about 1/8" to spare on each side of the inside of the frame rails. Of course I will have to do some work to get it up to where everything will clear and function, but that's par for the course.
 

Attachments

  • SS LINE CLIPS.jpg
    SS LINE CLIPS.jpg
    31.8 KB · Views: 36
  • 100_8616.jpg
    100_8616.jpg
    84.3 KB · Views: 45
  • 100_8621.jpg
    100_8621.jpg
    74.8 KB · Views: 54
Last edited:
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Ok. I have a question. I have a 4.6 DOCH engine for this project. I am going to stick with the "stock style" Lincoln Mark 8 radiator. I bought the "all aluminum" version off eBay. I will have to do more cutting and fabbing (which is what I do for a living), to get things to fit the way I like.

I have a few pics of what I am up against. I plan on cutting spacers to lift the bottom radiator supports (or just raising the bottom mount brackets), and trim off the OEM Lincoln "pin mounts". Then use the top stock mounts as well. Of course I will need to trim them to fit the 1" Lincoln width.

My question? What is the stock dimension from the top of the core support to the stock radiator? How far above the core support can I run this radiator so it still clears the hood? See the last pic for refererence. %)
 

Attachments

  • distance.JPG
    distance.JPG
    292.7 KB · Views: 45
  • 13.jpg
    13.jpg
    90.4 KB · Views: 46
  • 12.jpg
    12.jpg
    73.5 KB · Views: 39
  • 10.jpg
    10.jpg
    132.3 KB · Views: 40
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well I have measured (and measured!), and figured a few things out. I will have to cut into the inside frame rail to get the stock location for the fuel filler tube to work the way I would like. The tank sits level with the rake of the frame, but it is just clamped into place in the pics.

I was going to bring the filler in through the top, but I will never have enough room between the top of thre tank and the bottom side of the bed. I will grind a little material away from the inside of the driver's side frame rail and get the neck to clear so I can run over to the stock rear filler neck with the filler hose.
 

Attachments

  • tank 2.jpg
    tank 2.jpg
    88.6 KB · Views: 46
  • tank 3.jpg
    tank 3.jpg
    66.7 KB · Views: 49
  • tank 4.jpg
    tank 4.jpg
    65.7 KB · Views: 45
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
In reference to my last question about the radiator. I contacted another member here (thanks Explorer!) and he gave me the info that I needed in order to make a decision. He is running a custom aluminum radiator, which in his pic looked quite a bit higher than what I would need for clearance in order to utilize the stock Lincoln radiator with the Mark VIII 4.6 DOHC engine.

What he stated in his message to me was "Three inches from top of core support to top of radiator cap. The relief valve on top of radiator cap sticks up another 3/8". Hope that helps. No problems clearing hood."

I will use the stock mounts and cut/trim them, then weld them back up to fit my application. I will raise the bottom mounts up about 1 1/4" by either cutting the brackets and moving them up, or just using a simple spacer to raise the mounts up to where I need them to be.

The new radiator location will set in the bottom mounts and clear the top of the frame rails by 1/4" - 3/8" of and inch. That way I can use the entire Lincoln cooling system ... hopefully saving me alot of guess work later. %)
 

blazinchuck

Bronco Guru
Joined
Jul 14, 2005
Messages
3,319
nice tank...can you run intank pumps with it? i see more holes in it...or are those for different filler neck options?
 
Top