• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Electric Fuel Pump

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Hey guys, I have a '69 Bronco. 302 etc.

This is a street cruiser and really only gets driven during the summer and occasional winter nights. I'm having a problem with keep fuel in the lines in between starts. I try to get out to start it every couple weeks but it just doesn't always happen that way.

I went to start it to shuffle the vehicles around and couldn't get the bronco to start. No fuel getting to the carb. Had a buddy bypass that to get the motor running by pouring little bits of fuel in the carb as I started it (done it a few times before). Still couldn't get it going. I think the fuel pump is pretty much done (thinking the rubber diaphragm in there is rotted away).

To the end of the point. Im thinking of getting an inline fuel pump rated at like 7-9psi. Is that more than enough? Anything else I need to be aware of getting besides the block off plate? Any brand suggestions etc?

Thanks,
Joey
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Search Carter electric fuel pump here on CB. Lots of info.
I think these boys all use the P4070 part number. Someone will chime in with the correct part number if that one is wrong.
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
... I too think the P4070 IS THE MOST POPULAR Elec pump out there. Now I replace the stock fuel pump on the block. I just like it. and then I'd put in the P4070 PUMP just to push fuel from the tank to your stock fuel pump.
.. After it has set for a month .. Turn on the key activate the elec pump .. Run it about 30 to 45 sec. then turn off and recycle about 3 or 4 times before you try to start your ride.
You'll learn your ride. after a few starts .. But they sure start better with fuel pumped up to the carb. Before you start turning it over.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
The P4070 is one of the best pumps out there. Don't know if it is the most popular, but very well liked around here. They work. Rare to have a problem. People have been running them for decades. They will feed a carb without having to add extra regulators and other parts that can go wrong. Have enough volume to feed nearly anything that is streetable. Well proven and works.
 
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Really appreciate all the comments guys. I guess I'll be getting that. Are most people installing those with the stock fuel pumps or deleting the stock fuel pumps and running just the carter?
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
If your stock pump ever ripped its diaphragm the electric pump would push fuel passed that ripped diaphragm and fill your crank case with gas.
Run one or the other but not both at once.
 

jrwyant

Jr. Member
Joined
Jul 26, 2014
Messages
107
I replaced my mechanical fuel pump with that Carter P4070 pump, when I replaced my front dress converting to serpentine (which involved changing the timing cover to the later style, losing the mechanical fuel pump boss in the process), and have had no problems. (I had wanted to run a more modern reverse-rotation water pump, with the water inlets canted in the proper direction.)

I like that that Carter model is self-regulated, and so won't overfill the carb. I did get an "interlock" switch separately (for safety reasons), which I tee'ed into the oil pressure sender's tube: the carter pump only gets power when there's oil pressure. (Merely cranking the engine supplies enough.) I've never had issues with this setup.

Oh, and I couldn't resist wiring in a hidden dash switch allowing me to shut off the pump, as a kill-switch.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
True, but voltage drop is very hard on electric motors. Going with a relay more easily allows the use of an appropriate wire gauge for the length of the circuit. As part of the relay system I always include a oil pressure switch, which turns off the pump when the engine loses oil pressure - say from an accident. Buy the right switch and there is a third terminal on it to connect to the "I" terminal on the starter solenoid so that the pump will run during cranking. The original application for the switch that I use is for a Chebby Vega.
 
Top