• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Running a 96 PCM without transmission

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
Got your curiosity peaked?

I'm going to swap to a 96 f150 engine and auto transmission some day, but until I can get all the other parts I need to do the entire swap, would the computer run the engine without all the transmission inputs?
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
As it was explained to me the transmission can be programmed out of the PCM.

But when you put a computer controlled transmission in you will need a PCM programmed for it then.

You do know that the F150 EFI intake will stick up about 8 inches above the hood don't you?
The only F150 intake that clears is the 1993 to 1995 SVT Lightning or the equivalent marine intake. I've seen a broken one go for $300 on eBay.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
Its got an explorer intake on it. I'm just curious if I could use this computer and put another intake on my old 302/c4 still in the truck until I get drivetrain stuff ironed out.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
The only F150 intake that clears is the 1993 to 1995 SVT Lightning or the equivalent marine intake. I've seen a broken one go for $300 on eBay.

I picked up a marine version for $350 shipped. Looks like it never saw water.

Its got an explorer intake on it. I'm just curious if I could use this computer and put another intake on my old 302/c4 still in the truck until I get drivetrain stuff ironed out.

96 was the first year of OBDII just an FYI. Should have a E4OD/AODE transmission and remote TFI distributor. I'm still looking around for a way to use the stock distributor and wire it into the mustang harness. I've read people have done it but don't have all the specifics.

In order for the explorer intake to fit it either has the GT40 lower already or the BC adaptor. It's my understanding that 96 trucks are speed density and that's not the best EFI as the addition of go-fast parts i.e. the GT40 intakes does nothing for the performance.

I'm in the middle of a 96 351W from a E350 swap now (no timeline on completion). It's OBDI due to the GVW and it's also Speed Density. I've decided (well 95%) to go Mass Air to take advantage of the GT40 intakes, explorer throttle body and mass air sensor I have. Picked it all up for $35 a week ago at the local yard.

Tim
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
Explorer upper and lower. I'm good to go on the efi parts, just want a confirmation that the pcm won't run in limp mode without the 4r70w.

Timmy, you just have to cut your mustang harness apart and lengthen or shorten wires according to where you'll mount the tfi. I'm talking specifically about the wires to the distributor. Some wires will still go to the distributor, but the ones in the foil wrap will go to the tfi, wherever it's mounted.
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
"Limp mode" doesn't exist in Ford EECs & PCMs.


False, even the A9L has a limp mode.

I can't say 100% for sure how it will react, you will definitely get codes stored for the missing components, and most likely a check engine light.

However, if you trick the PCM into thinking it's in neutral (via the wiring to the transmission range sensor) then it "should" run ok without any torque limiting / limp mode like symptoms. The only downside to doing it that way will be the rev limiter. Most OBD2 Fords that I have seen have a rev limiter set around 5000-5500 rpm when in neutral or park.

I should have a better idea on the ETA for tuning those within the next 2 weeks.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
I was thinking about putting a mustang intake on my current 302 and using the truck computer so that I didn't have to finish a mustang harness to only have to finish the truck harness later too. If the neutral trick works, that leaves me with having to deal with egr and emissions stuff until you can flash the computer for me.
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
"FMEM" isn't "limp", so I guess I have answered my own question. ;)

You can call it a potato or potatoe, it's still the same thing. It would be foolish to publish internal Ford documentation, they get ugly about that sort of thing. How about from the NHTSA?



Random NHTSA article said:
When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode. Ford's trade name for the feature is Failure Mode Effects Management (FMEM) mode. In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained. ODI's complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM.

Now there isn't just one specific FMEM (limp) mode. There are various limp tables in every calibration. Which table or value is used is determined by the nature of the failure. In the topic of this thread the 2 that would concern me the most would be the EPC solenoid failure and the TSS. I could very well see either commanding torque reduction or other performance reduction. Not saying it will because I haven't picked apart that strategy (yet), but it's definitely a possibility.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Here's another famous quip for you: "If you call a tail a leg, how many legs does a sheep have?"
"5?"
"4. Calling a tail a leg doesn't make it a leg."

You can find documentation that the thing on the fender near the battery is a "solenoid", but that doesn't make it one. So if Ford - being the source of the EEC's software & its strategies - doesn't think it's "limp", then I fail to understand the relevance of citing someone else's description of it as such. You might as well cite GM documentation on it.

Is it a semantic distinction? Of course. Is the distinction relevant? Not necessarily in this topic. But it might be in another, so making the distinction here might forestall confusion later.
 

Ranchtruck

Sr. Member
Joined
Feb 7, 2008
Messages
768
96 F150 and Bronco were MAF, F250 and 350 could be SD depending on what emissions tier they fell into. I was prepping a 96 5.8l MAF harness for my uncles bronco.

I looked around a bunch for people who had done 5spd swaps into 5.8l MAF trucks, but since the trucks were rare to start with, the swaps were even rarer. One thing I did run across is confirmation that the older VSS that can plug into the transfer case produces a signal that works with the later ECU's and cruise control modules that were intended to run off a PSOM.

The concern would be torque reduction hiccups caused when the PCM intended to shift the transmission. Stock it retards the timing momentarily while it commands a shift to give the clutches in the transmission an easier time. So you might feel that driving it without an electronically shifted trans. I don't know if running it without the solenoid pack plugged in will default the logic to no torque reduction while the trans codes are set? My intent was to leave the solenoid pack and the prndl switch plugged in and play with them to see what worked. Unfortunately I had to leave before the project was done, so it's still carbed for now.

There was someone who had picked apart the 5.8l MAF code, so programming was available but they wanted $$ for it.

Any default programming that keeps the vehicle mobile while major sensors or actuators are dead is a "limp mode". Different manufacturers maintain different levels of operation in their "limp modes", some put the car in a barely operable state where others try and keep maximum drivability. Ford probably falls toward the latter. But without seeing into the code you won't know what it will default to.
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
Here's another famous quip for you: "If you call a tail a leg, how many legs does a sheep have?"
"5?"
"4. Calling a tail a leg doesn't make it a leg."

You can find documentation that the thing on the fender near the battery is a "solenoid", but that doesn't make it one. So if Ford - being the source of the EEC's software & its strategies - doesn't think it's "limp", then I fail to understand the relevance of citing someone else's description of it as such. You might as well cite GM documentation on it.

Is it a semantic distinction? Of course. Is the distinction relevant? Not necessarily in this topic. But it might be in another, so making the distinction here might forestall confusion later.


If the only "source" of information you care to acknowledge is from the manufacturer then by all means keep looking. FWIW the snippet I posted was from an investigation by the NHTSA, that was in the summary. If you care to look in to it there was an attachment in there that was from the manufacturer explaining FMEM and using the term "limp mode" to describe it to federal investigators. I'm pretty sure it was even on official letterhead. I only posted the summary because it also included the information about power reduction.

Many of the tuning software companies out there employ ex-engineers from the manufacturer to write the software. The term "limp mode" is used far more often in the software than FMEM. But, I guess that must be irrelevant because it isn't on official letterhead.

Sure, it's semantics. But the OP asked about "limp mode", if he knew what FMEM was I seriously doubt he would have asked the question in the first place. Since FMEM is nothing more than a trade name for limp mode, the whole semantics argument is the equivalent of " A Kleenex is not a tissue."

96 F150 and Bronco were MAF, F250 and 350 could be SD depending on what emissions tier they fell into. I was prepping a 96 5.8l MAF harness for my uncles bronco.

I looked around a bunch for people who had done 5spd swaps into 5.8l MAF trucks, but since the trucks were rare to start with, the swaps were even rarer. One thing I did run across is confirmation that the older VSS that can plug into the transfer case produces a signal that works with the later ECU's and cruise control modules that were intended to run off a PSOM.

Correct. That is even true in cases where the ABS unit provides the VSS signal. You can use the older style, gear driven, VSS to provide the correct signal.

The concern would be torque reduction hiccups caused when the PCM intended to shift the transmission. Stock it retards the timing momentarily while it commands a shift to give the clutches in the transmission an easier time. So you might feel that driving it without an electronically shifted trans. I don't know if running it without the solenoid pack plugged in will default the logic to no torque reduction while the trans codes are set? My intent was to leave the solenoid pack and the prndl switch plugged in and play with them to see what worked. Unfortunately I had to leave before the project was done, so it's still carbed for now.

There is no way to know 100% until the software is picked apart. But, from what I've seen in other PCMs I believe the only real concern is that the failed EPC solenoid will set the torque reduction flag.

The reason I suggested trying to signal neutral to the PCM is because large portions of the trans coding is usually skipped over when the neutral flag is set. But, the neutral flag usually also invokes a lower rev limit.

There was someone who had picked apart the 5.8l MAF code, so programming was available but they wanted $$ for it.

Any default programming that keeps the vehicle mobile while major sensors or actuators are dead is a "limp mode". Different manufacturers maintain different levels of operation in their "limp modes", some put the car in a barely operable state where others try and keep maximum drivability. Ford probably falls toward the latter. But without seeing into the code you won't know what it will default to.

Correct, the software is big $$. IIRC there is something like 17 different strategies and an insane number of calibrations for those trucks (which is odd considering they are somewhat rare). Since each strategy takes the pros literally hundred of hours to disassemble the cost is huge.

I do plan on spending the $$$ on it very soon, but I need to make sure the tax man is taken care of before I drop that kind of coin. I will likely offer a deal similar to the Explorer package even though it will take quite a while to pay for itself. I'm wanting to use it on one of my personal 460 EFI projects anyway.
 
OP
OP
Boss Hugg

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
Pooh, efi 460... I know where one of these, a 97 model sits, waiting for purchase. When I drove by it the other day, I thought about how the pcm would need to be flashed and all that jazz...
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
Pooh, efi 460... I know where one of these, a 97 model sits, waiting for purchase. When I drove by it the other day, I thought about how the pcm would need to be flashed and all that jazz...

The OBD2 5.0, 5.8, and 460 PCMs all share the same hardware codes, only the calibrations are different. So the same software will work for all of them. You could even re-flash a 460 tune on to a 5.0 PCM.
 
Top