• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

do lug nuts go bad

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
so ive had my current wheels which are eagle alloys for about 15 years ish. and as i was driving it down the drive way yesterday i hear a clicking type sound turned around came back and the left rear wheel lugs are loose. tightened them back up with an impact then breaker bar. drove a few miles got out to check and there loose again. the others are fine. the lugs are the same ones ive always had. any ideas.
 

66BlueGoose

Contributor
Sr. Member
Joined
Feb 6, 2014
Messages
408
Threaded components do get worn over time, both nut and bolt(or wheel stud in this case). That said, it's more likely that your wheel studs have become loose and are not pressed properly into the hub/axle. Thus when you torque the wheel nuts down they are spinning and not tightening down all the way.

You can pull the wheel off and check to see if they wheel studs are loose, if they wiggle, they should be replaced. It could also be the case where the hub or axle flange is worn and besides wheel nuts being replaced, the hub or axle might need to be too.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Once a wheel and studs have been driven on while loose they are probably both bad. The holes in the wheel get wallowed out a little bit and the studs take a beating. I've had one where the lugnuts would bottom out on the rotor and the wheel was still loose.

Until you fix all the damaged parts it will just keep happening. Over torqueing the lugnuts will just make things worse as the studs are being overstressed as well as beat to death.
 

Okbroncoman

Sr. Member
Joined
Dec 31, 2010
Messages
654
Sometimes you just need to put them in time out.
And tell them what they did wrong

Worst case take their phone away

Sorry had to say it
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Once a wheel and studs have been driven on while loose they are probably both bad. The holes in the wheel get wallowed out a little bit and the studs take a beating. I've had one where the lugnuts would bottom out on the rotor and the wheel was still loose.

Until you fix all the damaged parts it will just keep happening. Over torqueing the lugnuts will just make things worse as the studs are being overstressed as well as beat to death.

That's been my experience too. Once run loose, the tapered seats and/or/nuts loose their surface to hold.
Don't be tempted to use Loc-Tite. The lock isn't enough and will get you into trouble.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
Once a wheel and studs have been driven on while loose they are probably both bad. The holes in the wheel get wallowed out a little bit and the studs take a beating. I've had one where the lugnuts would bottom out on the rotor and the wheel was still loose.

Until you fix all the damaged parts it will just keep happening. Over torqueing the lugnuts will just make things worse as the studs are being overstressed as well as beat to death.

That's been my experience too. Once run loose, the tapered seats and/or/nuts loose their surface to hold.
Don't be tempted to use Loc-Tite. The lock isn't enough and will get you into trouble.

^^ What they said +1
My experience has been the same.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I've found that the stamped steel wheels are far less prone to have this problem. The hollow under the lug nut compresses when the nut is torqued on and the flex allowed by steel doesn't beat up the nut, stud, or wheel.
 

turbotim2

Contributor
____________
Joined
Jun 26, 2003
Messages
2,158
I am not sure how powerful your impact wrench is but alloy wheels shouldn't be torqued much beyond 100 ft-lbs. They all should be torqued evenly and re-torqued after driving 50 miles from install. Alloys expand a lot when they get hot.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Use a torque wrench to install your lug nuts otherwise your just guessing. Many tire shops have paid the piper for not using one.

What ever you do don't use a nut to pull in your new studs. Pull the axle or hub and press them in from the back. Using a nut to pull in the stud on a proper press fit will over stress the threads and cause early failure of the studs. You don't want your wheel beating you down the off ramp on the freeway like mine did.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
got the new studs pressed in and everything's tight. hopefully it stays that way
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
How is the wheel? Often the holes in the wheel also get damaged. Which will start the chain of failure all over again.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
As a thought, I have known some unclean persons of canine ancestry that thought it was funny to loosen lug nuts on vehicles.

Hopefully that is not what caused yours to be loose.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
As a thought, I have known some unclean persons of canine ancestry that thought it was funny to loosen lug nuts on vehicles.

Hopefully that is not what caused yours to be loose.

nope dont think so its been locked up in the garage. I did drive it a little this evening brought it back and the dang things were loose again. I torqued them to 100fp initially. Soooo this time i used the pull handle and tightened the crap outta them. drove another 20 miles or so and not loose yet. maybe they'll stay that way. weird thing all the others are staying tight.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
and by loose you can barley hear the wheel squeaking/popping at low rpm there not floppy loose
 

Prizefighter

Bronco Guru
Joined
Feb 24, 2010
Messages
1,195
This happened to me yesterday. I put mine on with an impact a few months ago and haven't driven it much. While driving yesterday it started popping. I drove 10mph on back streets and barely made it to my parents house with 2 lugs on.

The wheels are brand new but I used old lug nuts... I have learned my lesson as that Dick Cepek wheel is now toast. I will use it as a spare since it doesn't look horrible I just don't trust it now.

I checked the other wheels and they were not tight either. Close call!
 
Top