• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Strange EFI Issue

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Engine is a 410M (351M block bored 40 over with a 400 crank) with '89 Mustang EFI. It starts right up and runs fine. After it's warmed up and I shut it off it won't start. Turns over but no fire. Let it sit a few minutes without cranking and it again starts right up and runs fine until you shut it off. It never has quit while running - it just won't start back up immediately after being shut off. It does not have to cool down completely as just sitting a few minutes will allow it to start up again. I have not yet pulled codes. Any ideas??
 

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Pull the codes and eliminate some of the guesswork first. Too many variables with EFI.
 

Bronco Brian

Bronco Guru
Joined
Feb 10, 2006
Messages
1,140
Just Curious how do you get Mustang EFI on a 351M? I know how you can on a 351W but a 351M would make a lot more Torque.
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
Just Curious how do you get Mustang EFI on a 351M? I know how you can on a 351W but a 351M would make a lot more Torque.

You use an Edelbrock Streetmaster single plane manifold modified with injection bungs and a 4.6L 90 and throttle body. The rest is straight Mustang EFI stuff - harness, MAF meter, computer, sensors, etc. It starts and runs strong except for this new issue of not starting after running. In the spirit of full disclosure, this is in a 78 Bronco!

 

TN1776

Bronco Guru
Joined
Oct 24, 2006
Messages
2,632
I'd definitely pull codes first, but with an issue like this I would bet you won't see any codes.
I'd then verify that you have spark when its failing to start - and if not then I'd suspect maybe the TFI module has some kind of issue.
Then I'd check fuel pressure at the rails.

Beyond that... I'm stumped.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Maybe try the old flooding trick of holding the throttle all the way to the floor to see if that helps fire it up.
Yes, I realize this is a carb trick and not usually associated with port fuel-injection, but hey, can't hurt to check. Right?;D

What I'm thinking is that perhaps at full line pressure the injectors are somehow leaking fuel into the intake and it's acting like it's flooded.
Maybe a simple fuel pressure gauge would tell the same tale? If it's not holding pressure for more than a few minutes, it's leaking somewhere.
Usually the regulator is suspect, but while I've never seen leaky injectors, I've heard or it happening.

Also, if codes don't tell you anything, check your coolant temp sender and intake air charge temp sender. Maybe one of them is sending a bad signal.

Good luck.

Paul
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
you can stare at it some more and talk about it on the internet, that aint gonna fix it.
gotta get in there to find a clue.
as already said above
Pull codes
check fuel pressure
TFI's do weird stuff, best to throw in a new known good distributor ( you should always have a known good spare)
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
Mine did that and it was the coolant temp sensor for the PCM
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Mine does that too and it is the check valve in the fuel punp I think. When the pump runnning I have 40 psi in the rail but as soon as I shut it off it drops to zero. IF I punch the rubber line going into the fuel pump it holds.

Short story is when the fuel pressure drops the fuel can boil making it impossible to start. What I do is turn the key on for 3-4 seconds, shut it off, repeat thtee times. The ECM only runs the pump for two seconds when the key goes on so you need to repeat it a few times. Then the pump can build pressure in the rail and push the vapor back to the tank. Try it does not cost anything!
 
OP
OP
Scoop

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,124
Loc.
Cuchara, CO
I'd definitely pull codes first, but with an issue like this I would bet you won't see any codes.
I'd then verify that you have spark when its failing to start - and if not then I'd suspect maybe the TFI module has some kind of issue.
Then I'd check fuel pressure at the rails.

Old pic. I do have a fuel pressure gauge mounted on the rail and it shows 30-40 lbs. 30 at idle and 40 when revving.

Beyond that... I'm stumped.

Maybe try the old flooding trick of holding the throttle all the way to the floor to see if that helps fire it up.
Yes, I realize this is a carb trick and not usually associated with port fuel-injection, but hey, can't hurt to check. Right?;D

Agree and I tried that already! Didn't make a difference.

What I'm thinking is that perhaps at full line pressure the injectors are somehow leaking fuel into the intake and it's acting like it's flooded.
Maybe a simple fuel pressure gauge would tell the same tale? If it's not holding pressure for more than a few minutes, it's leaking somewhere.
Usually the regulator is suspect, but while I've never seen leaky injectors, I've heard or it happening.

It holds the 30 lbs fuel pressure when not running - I'll check to see if it bleeds down and how long it takes.

Also, if codes don't tell you anything, check your coolant temp sender and intake air charge temp sender. Maybe one of them is sending a bad signal.

Good luck.

Paul

you can stare at it some more and talk about it on the internet, that aint gonna fix it.

You might be right, I've been staring at it a long time and it's not fixed yet. Wait, I haven't tried Face Book - just might work . . . ;D

gotta get in there to find a clue.
as already said above
Pull codes
check fuel pressure
TFI's do weird stuff, best to throw in a new known good distributor ( you should always have a known good spare)I do need to get a back up dizzy. It's a stock Windsor 5.8L one with the gear changed to match the 351M.

Mine did that and it was the coolant temp sensor for the PCM

I was hoping someone had a similar issue to point me in a direction - thanks surfer-b. I'll pull codes probably tomorrow and maybe start with the temp sensor.

Thanks for all the help!
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Maybe try the old flooding trick of holding the throttle all the way to the floor to see if that helps fire it up. Yes, I realize this is a carb trick and not usually associated with port fuel-injection, but hey, can't hurt to check. Right?;D

This works on mine. I always thought it was a carb trick but the first time I shut off the engine (Mustang efi equipped) at operating temp and it wouldn't start I tried this and it started right up. We thought it was an ignition problem and changed the dist. cap and rotor and it still wouldn't start. Got in, floored the gas and presto...fired right up.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
EFI have "clear flood" mode when you floor it and the engine is not running. Sends no fuel pulse.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651

Man, haven't seen that setup in a long time. Good to see it again!
Kind of miss the old PJB site now and then. Lots of talking about our old full-sizes.

Hope you get 'er figured out and fixed up.

Paul
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
I'll pull codes probably tomorrow and maybe start with the temp sensor.

When mine was acting up it never showed a code, not saying yours want and it is a good place to start, but don't be surprised if nothing shows up for the temp sensor.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Also do a check for spark. Get it good and hot, pull a wire and make sure you are getting a good spark. Easy check. Is that one of the TFIs that has a start wire on it? is that still working correctly?

Just a few ideas instead of chasing fuel.
 

WSM29

Sr. Member
Joined
Mar 29, 2010
Messages
371
This isn't a sign of a coil going bad is it? Had the issues before with a coil getting hot and not working again til it cooled down.
 

Bronco_69

Bronco Guru
Joined
Jun 14, 2001
Messages
2,070
Loc.
Monette Ar
Also do a check for spark. Get it good and hot, pull a wire and make sure you are getting a good spark. Easy check. Is that one of the TFIs that has a start wire on it? is that still working correctly?

Just a few ideas instead of chasing fuel.



this! check for spark.

i had the same issue and it was the electronics inside the distributor. i changed it out and no more issue.

it was NOT the TFI. i changed that first
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
EFI have "clear flood" mode when you floor it and the engine is not running. Sends no fuel pulse.

Ya know - I've yet to find a vehicle that it works on. My 95' F150 would start when WOT, my 89GT PCM will start WOT too. I'm not 100% certain that is true for everything.
 

ren71

Sr. Member
Joined
Oct 13, 2010
Messages
536
I third the tfi module, it's not really a waste to buy a new one and try it even if it isn't the problem. It's good to have a spare since they are known to go bad eventually. That's why they redesigned the later cars with ithe tfi away from the distributor/heat sources. Hit or miss on different parts store brands though but I'd go with a ford module since they probably made better revisions, I think they even got class action sued because of the older ones iirc.


Found the class action:
http://www.nytimes.com/1997/09/06/us/lawsuit-asserts-ford-knowingly-installed-defective-mechanism-millions-vehicles.html

Better article:
"Making the problem even more insidious is its phantom nature. A TFI module can fail on an intermittent basis when hot, then function again when the engine cools, without leaving a trace of physical evidence that the TFI module had failed." Pretty much every tfi system till 95
http://www.autosafety.org/ford-tfi-module-national-class-settlement
 
Last edited:
Top