• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

9" 35 Spline Axle Help

5001craig

Contributor
Bronco Guru
Joined
Nov 3, 2013
Messages
1,180
I've done some researching and am kind of stumped. The only thread I saw was from 2006.

I'm upgrading my 9" to 35 spline axles. I already have them (Wildhorses 35 spline kit + disc brakes). I didn't really realize this but it looks like I need a new center section to go 35 spline? When I talked to WH, they said everything else was useable.

I'm also changing the gears from 3.50's to 4.56 or probably 4.88's (been studying gear calculators for a few days here which is an awesome gear calculator) and was already planning on going with new diff's for the 35 spline axles. Leaning towards Grizzly Lockers front and rear or possibly an E-Locker front and Grizzly rear.

Any help on what I need to go from a 9" 28 spline to a 35 spline would be greatly appreciated. Moser is pretty close to me but I really don't know what I need and can't find it from researching.

And since no thread is real without pics, here's the axles and disc kit I have:

GahcGWPDxGSC--YfOfL4lw9_G3459AOqxQ0eh-CuwVKF399JfpMRa9uH7LIGoL1HKsIh41BwAip-MOSknQhnlP7RCcahu3CRrJ0YqXTA3gu-ap6QiQeAQM3_ZQMlmfn8RoFJK3f98oy5ZgQRvaPhNPuC4v8_lNsTczrtex6PNIq0PokSRX1dSAD784mysboq8YcVV8ypfdLsDfZIXdNHJje_23fpWC9fhV21Wtg0qBt__1yo4nAzhyYymkpqUNKCruENjFFenwFV1ikSZjqDetf0BCW8Y2MgwBGQ67UQPJfSCZ9dPgtejzqZO7HGRZhw1jOQ0tfjdxCAN5VlckuimqTEzQ9zMSaqjD3wGqOVY7X8avOOjIpSzC-4SStt2yyobrgQJxxK4nZN6PShXUvlrqeQ8AHAGtSMis-BXP1RQVgmKevbGTw1nUMLlf-ndrbr04tU2_1gS9ChRnlfwQpvdehrDSY04EGpXhzJEYtcIEHpof7xuxBg0Hc8gvLOIQ_v-YbLEnZEhRpUY0f6Q2B_lpxE9M-MH4BdSo00tNwXrBBPySOBd1N0n5nR0CFN4tl1Aw5fkA=w556-h985-no


BXEyLgE1Ida5R7WmFQrGtzth1DjmPkbWGDiEUUKihxUasgTZG-VtGC3TNlo8F9NvDlMgrB0jsIj9TO1bCUJhnbyo8kyp7SuaBd0K8Ve44IRbi_s_5BNltBNPN8O8IBGxD5zEor7nmi1jLDIyngA96HsDk2xNnx2VtdZ1_WVr8Huo-5IjR3PTDhbSCenoR34NWabtueOLZuni_tvDMMmIHaK7qBPypRc_UQrgx_wGnTxW1QJTJEN2VjlFEHVmOwNUttMoBjir3H0Fwhyzb78ReEo5CmyR3F9bLK3zorN546wM7FgTb3KpBs_WGFJD9jD3n8HM29Y3yKPe0FHcYlC-HoS8ZeN4Z5hvCp1ooxsnv38VslESL6PjdPGns8i1nP-OBDKpJZuVediYYW6nmId7i_Z3z-dAMzY9pB5M9BBS3yre6zXT07sEFb9y8tkB7DlHcYaWOx7fgEBbyvxSldBAn2V1dKPgZpDZUsNdludUBBHK5nMMHz-QMCt6mrhzntYDMU_3ie_CsFeAz95n5SGQp-B_ajzf4k64zow4otL6QtAXokLKy7pEtEiUsnwy-Y3wQOxewA=w556-h985-no


GHkn1hufxaFxhVwdoNL81w4lGng4hirjAbbp8PGk419V5CfBriyoHkdQPboFZRnYGvkas70OVo6mZ3gO2WmCTmR4HuG36Io7HcAPWUoNXR9gFQBAbSmCus43Ezg4pc58-CG_PoHkh063BHKkPvk59fNGkKJVdM7u4PPnx3x1jquIaKWfsJypiOWBwJfdhtTfSdnaDztxIujkk-oEl1xoz576F24efCE2uljtL6rlrJElZ_cf7393YLu-zM2Z8kZ5Pdc5sAdywtJZsj5aKLT9j71wWkW8DfUjvXkqEJ-kePRdZnDn6iI7AQpe3OjLYKw9PcWS88jCu_z2BQZfnSubUSf3R-LelxPnSabNRieqrwTsj-1csWyLI897QG4psmPOy248MCE5lUo9EKm9lSDg8MT2ypxSc5zyiD8GxKl6mX0pXHrMPOJGdLMf_l5hzS8wrx1Lx5ppu6mxtepoeq_dvzYuJhcQePDYV7aLqKt5t8u2NsHNWVKgRooS__CpPg-qlLvoMYlYDrZKlHZs9rWP34kkjs09zwxpmHotyGlfuORMS-8ScxIdLahzIRsM7SFPgm3W0g=w1753-h985-no
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
You will need a new carrier with 3.25" bearing jurnals. A 35 spline locker of your choice. I would also do a Daytona pinion support, it's not required but a good idea and will ensure your pinion bearings live a long happy life. Ring and pinions are all basically the same and will work.

If your interested in an assembled 3rd let me know
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
X2...make sure you get a master rebuild kit for the 3.25" case, as the carrier bearings will be different. I would also suggest that you run the Daytona pinion support for the minimal cost difference (billet aluminum or nodular doesn't matter IMO) and the bigger bearings, but no need to step up into the 35 spline pinion stuff. Definitely get a master install kit with the solid pinion spacer upgrade instead of the crush sleeve.
 

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Same issue last year but 31 spline was fine for me. I went with a complete third member from Toms as they have a guy that does it in-house. So if you call you can ask for him and he can answer any questions you have like break in procedure or oil weight for your part of the world. Most vendors source that work out. They don't advertise 35 spline but it won't hurt to ask. On the front I dropped off diff at a 4wheel parts store and they installed the gears I provided for around 450 with a 7 day turn around. I went with a grizzly in the back and detroit in the front
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hey Craig, sorry for the misinformation and the problem it caused. There were in fact some few factory third members with the larger bearing bores, but those would never (unless just by accident) have been found on a Bronco to my knowledge. Mostly the big-engined muscle cars I believe.
The 31's are a direct fit of course, but in most cases if you're using stock, the 35's require the upsized third member. As the others have said.

It's a nice upgrade of course, but doesn't change the fact that it's not quite as much fun when you don't expect it.

We carry the Yukon chunk, but not sure if we still stock them or just order as needed. Easy enough to find out though.

That's the same brake kit I'll be installing (one of these days...) in mine, but with the 31 splines instead. Wanted the 35's too, but knew I would not be changing my gearing until after the swap, so would not have had the opportunity to get the larger housing and had to stick with the 31's. Probably fine for me, but for that little extra, I sure would have liked the 35's:cool:
Just because, don'cha know...

Let us know if you'd like to swap them for 31's, or if you'd like to check on pricing an empty chunk. Of course, living near Moser isn't a bad thing when you have to always add shipping costs to some of these heavy parts!

On a side note, was out for a birthday dinner earlier tonight (mine and mom's) and we stole (with permission) the pen from the waiter that was from Cheers like in your little keepsake in the first pic. Thought it was pretty cool even for just a lowly pen.

Paul
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
If you are going to 35 spline you should be planning on a nodular iron third member case as well as the Daytona bearing support.

I would use those with 31 spline as well, if those were my plan.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
What sykanrOng said... my .02 is don't waste your hard earned money on a set of almost bullet proof axles only to have the weak point be the housing and have it blow up on you--literally. You are throwing money away unless you upgrade to nodular and a Daytona pinion support...at a minimum. I've grenaded housings with 31 spline axles, it's not that hard. Do it right once... (wish I would have!!)

Unless you are going with super low gearing (multiplying torque #'s into the thousands) you don't need 35 spline axles, but if you have them already...

btw, call Moser since they are close as they will tell you exactly what you need and supply you with the parts needed.

Good luck, go wheeling!
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
If you are going to 35 spline you should be planning on a nodular iron third member case as well as the Daytona bearing support.

I would use those with 31 spline as well, if those were my plan.

Absolutely! The stock case will eventually fail, low gears and aired down tires are just too much for the 40 year old stock case.

I'd price everything you need, then compare it to a TrueHI-9. Those are really nice for our short drivetrain Broncos. You'd be miles ahead if you ever wanted to put in a doubler later on. A Grizzly equipped Hi-9 is $2429.00.

http://www.truehi9.com/Prices.html

Mark
 

Lmfp

Bronco Guru
Joined
Jun 28, 2011
Messages
1,496
Loc.
Lake Charles, LA
My next project is a 35 spline rear since I just blew my 28 spline stuff. Gotta local shop building my center chunk with the daytona support and grizzley locker. All assembled ready to install with shafts is coming out to $2400.
 

sykanr0ng

Bronco Guru
Joined
Aug 11, 2014
Messages
5,363
Several here have recommended the TrueHi-9

The trouble with that as I see it is that a high pinion in a rear application is putting the pressure on the coast side of the gear which is much weaker.
 

sanndmann3

Contributor
Bronco Guru
Joined
Jun 13, 2007
Messages
1,832
A heavier duty rear is in my future as well.I was thinking Moser 31 spline axles. haven't had any problems with my 28 spline stock stuff to date but i run primarily sand dunes rather than rock crawling so i think not hooking up so hard has saved me so far...
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
Here's a quote from the Hi9 shop...
"Yes, standard-cut high-pinion gears would be more practical in the rear if they existed" Weivoda admits, "but we've found that running on either side of the teeth is equally strong as long as deflection is controlled."

With the thrust block you don't have any deflection at all which also takes the stress off the case which prevents grenading it also... the third pinion brg also offers extra support and increases it's "load" capacity.

Another advantage:
What is the benefit or disadvantage of a larger/smaller ring gear?

A. A larger ring gear allows the same number of teeth to be larger. This means that if you have 40 teeth spread out on a 10.5 circle they will be larger than if they were spread out in an 8 inch circle.That is why a GM 10.5 14 bolt has such huge teeth with very little pinion offset. BUT the Ford 9" already has larger teeth than a Dana 60 so there is no advantage to the Dana 60s' 9.75" ring gear vs the Fords' 9" ring gear.

With a 5.14 gear ratio you have 3 pinion teeth engaged with a 9" and less than 2 pinion teeth engagement with a D60.

Another advantage of the TrueHi9 or any 9" for that matter, for me is the "snout" or distance the yoke is from the center of the axle housing. The Dana 60 pinion sticks out longer therefore you must have a shorter driveshaft...

Here's more info... http://www.truehi9.com/gears2.html

Have fun go wheeling...
 
Last edited:

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Several here have recommended the TrueHi-9

The trouble with that as I see it is that a high pinion in a rear application is putting the pressure on the coast side of the gear which is much weaker.

This might be true for the Currie 8.8 hi pinion, but the True hi-9 is a completely different animal. It would probably be the last weak link in a Bronco drivetrain.

Mark
 
OP
OP
5001craig

5001craig

Contributor
Bronco Guru
Joined
Nov 3, 2013
Messages
1,180
Thanks for all the input. This is the best site.

I am staying with the traditional 9" rear--just upgrading the axles and I really liked the convenience (as well as design) of the WH upgrade kit that includes the discs for the rear. I have looked at the 9"/D60 outers but for the front.

I had a big day today and didn't get much of a chance to research this topic. I did get with Summit on the road and the parts for the center section alone come to $1,429 and that was I believe without one part that was $100. Included was the Summit nodular case (SUM-CTDHNI3250), Summit pinion support (SUM-730919), Yukon Grizzly Locker (YGLF9-35), Yukon R&P (YG F9-486), Daytona pinion bearings (PB028) and a Yukon Master Overhaul kit (YK F9-HDD-SPC).

My EB goal is to have something that has good power and is bullet-proof. 408W should handle the power end and the Atlas 3.0/35 spline will help in the reliability end. Just need to finalize the C4 and upgrade the D44 (gears and swap the Lockright to a Grizzly). Also will be installing the Duff Monster 3.5" lift with the 4-Link rear mainly for locating the axle. I don't know jack about designing a 4-Link. I will note that I mainly offroad in the sand at Silver Lake and IMO sand is more forgiving than rocks or onroad (my father in law has been running Lockrights with 33's, 4.11's and around 300 hp for years and has only had to upgrade to chro-moly axles in the front). He gets on it pretty hard. I realize driving style has a ton to do with everything, though.

Not to hijack my thread but last spring I had my shafts lengthened, rebuilt and balanced (1310's). I stayed with 1310's on the Atlas when I ordered it (I will probably get flamed for this). Today, I was looking at Diff Wizard parts and saw a 1310/1330 Adapter U-Joint. Was thinking about the idea of going with 1330 for the rear yoke and 1310 in the shaft. Not sure if this would do anything as the weak link is still the 1310. I've also read that the 1330 is not much stronger than the 1310 (I believe the caps are the same diameter). At least the rear would be ready for 1330's when I go that route...

Hey Craig, sorry for the misinformation and the problem it caused. There were in fact some few factory third members with the larger bearing bores, but those would never (unless just by accident) have been found on a Bronco to my knowledge. Mostly the big-engined muscle cars I believe.
The 31's are a direct fit of course, but in most cases if you're using stock, the 35's require the upsized third member. As the others have said.

It's a nice upgrade of course, but doesn't change the fact that it's not quite as much fun when you don't expect it.

We carry the Yukon chunk, but not sure if we still stock them or just order as needed. Easy enough to find out though.

That's the same brake kit I'll be installing (one of these days...) in mine, but with the 31 splines instead. Wanted the 35's too, but knew I would not be changing my gearing until after the swap, so would not have had the opportunity to get the larger housing and had to stick with the 31's. Probably fine for me, but for that little extra, I sure would have liked the 35's:cool:
Just because, don'cha know...

Let us know if you'd like to swap them for 31's, or if you'd like to check on pricing an empty chunk. Of course, living near Moser isn't a bad thing when you have to always add shipping costs to some of these heavy parts!

On a side note, was out for a birthday dinner earlier tonight (mine and mom's) and we stole (with permission) the pen from the waiter that was from Cheers like in your little keepsake in the first pic. Thought it was pretty cool even for just a lowly pen.

Paul
No worries Paul. It is on me to do more research. I wouldn't change the direction I'm going--the center section just wasn't in the budget. I will work through it.

On a different note, I received my Painless Wiring kit today from WH. Got movement just looking at that beauty. I HATE wiring and feel this is money well spent so I can get through it (I have flashbacks of wiring my Cobra replica when I hit a brick wall). After reading through the impressive manual it doesn't seem that bad. We'll see...

Here's a lot of wires--I was surprised:

nQ8qQU1xJtDStDNI688j_A21ukP91KbCsibsYDb3w7sHOdvTY5s6FhXOtNRUIdgVDJwp8X_OlvzAxXW483CZlb5vm5Nctwb72CKe0_A9eRcZ6JZnsQYLMWQS2oR7enlZRrCWYH7zAx5y-VD-EEAT7xrm-66W8CBrYtl0f7R_3MbT24HPeCGhJ9yJ8uJgah4ga7cI8QVeRTz9r555rrMy4jBu61Z9fUqlaozZ8A1COxmmxAgD9EqbE3rvANXgx9a7XevmsatVDhaWAitlwxBVGEdRR-NRT4B9lLsIN3GHReALPd_0vK01U-kQbup_6v2iRHETEcdZe34DPGW-IUKB7DQoVjPkc2oaY2EUc_Hj-dYgyi6wd-HwdBErpbd9IecpQtJYv6L6KE0lWlQjFlBA9yt1hNmkt0d8JYqlue-m3xDL0hGqcG5RMsUccIQ5QMcEjt3LCxgZFcdNm4a3co22gXxx12Ig7wsjUjM4lk4k-YKw6TmdiM5J2rj_EjuChsVBUaRl_fgowSfWXfr1BdL90VqPQwZSuY7RlkZcTvkAvvwCtIzi2sfZPHpdTtChV4hwHe6hXA=w1753-h985-no


And I really wanted the Wiring Loom. Very happy I got it as it's very nice.

ewTRex0m5l9rbfhig6EYuKComyHqFJkDtMTGj7WT5LkmcJGS9-FmXGlw9dARnsIYUFhJQS2N6_m83vKw4LMfwEr7J0jZiCmLS4J4DlZkGgKvMRtW9KAhA_DRWLDI03hur6P4AFIkD0R9_S94sPmdNq_J3i4FQPsxaS4JURSejfAKaVdXDwV_urnW12lBsrNfmngAdEJPoEbSOwGHaGeEHwKSwqL1CVEvhyFdvtmrmJ2Jjzf_bGSOsZsb1vHFkoYhT5SvtM7F8M4qAkAVeC5R1vQ493ebTDn318Mgf-hHrI5af6XFxTpZeevieHD-gEbjoYgWqVY3GSlCERzJ0mrheE_hvyF6Tt4Zat-ANFkYCPD2qvUkcPn7cS2pbpp2wQze1YgTU2EeY-EdfhFNnrR-oGEZpkcBPIPOiutUUEFPHwr6vu5UKd-cw4_ysJhHOQ0dxIR4TqG_Bc-BUz8sKg4gf-z7FaFxh51UaN_pXnE50u9ixKBJo-4mi-UVubrNhSJAVAvb3lSqcfCychdAs9Db77mpZri6xGHY65-35I3MJY5Ta3VvwmrLlwS0Y0EVuDfjAlFfUw=w1753-h985-no
 

brewchief

Sr. Member
Joined
Feb 11, 2007
Messages
877
You can use 35 spline axles with a stock third IF you are willing to run a spool, a small bearing spool is available that fits 35 spline axles and uses the small bearing third that comes stock. I have been running one for a few years now, not great if you spend any time on the street but works great at the dunes.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
Saw your "Painful" harness... I just used one and if you are using an early Mass Air meter you are ok. If you upgraded to a later model like ProM, example, your 4 wires going to your Mass Air plug are wired wrong and the Painful guys don't know it (or wont' admit it). The ProM guys were fully aware of the wiring issue...

Do you have the rectangle plug or the later model semi-oval shaped one?
 
OP
OP
5001craig

5001craig

Contributor
Bronco Guru
Joined
Nov 3, 2013
Messages
1,180
Saw your "Painful" harness... I just used one and if you are using an early Mass Air meter you are ok. If you upgraded to a later model like ProM, example, your 4 wires going to your Mass Air plug are wired wrong and the Painful guys don't know it (or wont' admit it). The ProM guys were fully aware of the wiring issue...

Do you have the rectangle plug or the later model semi-oval shaped one?
New motor is carbed. Really wanted to go EFI but that's going to be version 2.0. The Blueprint 408W I was looking pretty hard at had EFI but I chose local build and forged internals over crate and cast.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
Sounds like you're good to go...

I was following their schematics and color code and Painless was wrong, totally wrong. I called ProM, they confirmed what I was thinking but didn't have the knowledge base at that time to wire it up differently than their schematic and two techs I talked to... anyway, I'm glad I didn't follow their lead as I'm sure I would have needed a new calibrated mass air meter... one of their techs said the '89-93 harness only worked with '89-91 mass air meters and that the resistance within each year's mass air meter was different and that you couldn't use any other meters with this harness, blah, blah, blah... I told him ON THE BOX it said '89-93 conversion...oh well, that's when I called ProM who build my meter and was given the correct wiring schematic.

Just a heads up...
 
Top