• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wild Horses Shorties + 4R70W

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
Back in October I ordered a set of ceramic coated shorty headers from Wild Horses. Soon after they arrived I had to leave town for work. This weekend I went to install them and seem to have a fitment issue. The exit flange is rubbing against the bell housing and resides in the exact same location the transmission dipstick tube wants to live. In the picture below the dipstick is unbolted and pulled out of the hole in the transmission just resting out of the way. Did anyone else running a 4r70W tranny and these headers have the same issue, or do I have a weird set?
 

Attachments

  • DSCN2793.jpg
    DSCN2793.jpg
    52.5 KB · Views: 189

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Hmm, seen that problem with non-stock C4 pans and dipsticks, and also a ZF bell housing just last year, but not sure I've heard of any 4R70 issues until now.

They definitely want to occupy the same space, don't they?
Normally I'd say put a bar into the header and bend it away, but I'm not sure that would be enough.

Will be interested to hear what others say as well.

Good luck.

Paul
 

rcmbronc

Contributor
Bronco Guru
Joined
Dec 15, 2003
Messages
2,778
Loc.
Tomah WI
Interesting. I want to know this also as I am looking to buy a set of headers this spring.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I have the Hedman headers (no where near as nice as those flanges) with the ball and socket flange but they are loose and you can rotate them. Even rotated I could not fit the dip stick in so I had to make a wedge shaped cut in the collector then bent it away then re-welded. Killed the finish on the headers but they had been on for years so they were looking a little rough. But hey it fits! Driver's side fit perfect.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That's with a 4R70 auto trans Lon? Same dipstick location as Halfcabs?

Thanks

Paul
 

green77bronco

Sr. Member
Joined
Dec 10, 2004
Messages
466
Loc.
SAn Antonio,TX
I have a set of wild horse shorty headers, but mine are 10 plus years old. Not sure if yours are the same design. But I had to pry the header back about an inch or so. And I used a flexible dipstick, as the the stock dipstick for the 4r70 wouldn't work. But you might be able to bend It to work, I just didn't want to hassle with it.

http://m.summitracing.com/parts/lok-xtd-3aodfm36
 

broncoman1972

Bronco Guru
Joined
Mar 4, 2004
Messages
1,300
I have the Bronco Hut Sanderson headers that Lon L linked to. 4r70w, same dipstick location as halfcab. Fits good, no clearance issues. Not a great fan of the 3 bolt, flat flanges but they aren't leaking so that's all that matters.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Thanks for the info. Yeah, I'm not a huge fan either. Like the headers overall, just not the flanges. But Stage-8's can help there too if you ever end up fighting recurring leaks.

Paul
 
OP
OP
67 Halfcab

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
This stupid exhaust is getting on my nerves! :p First I tried a set of Hedman 88408s. They fit great with plenty of room for the factory transmission dipstick, but would require a flexible braided engine oil dipstick. The primary tubes are so tightly packed together there is no way to snake the factory tube through it.

Next I tried the Wild Horses shortys. Plenty of room for the factory oil dipstick, but will probably require a braided transmission dipstick tube. I spent almost 500 bucks on a set of headers because I wanted to use factory dipstick tubes!

Maybe I'll have a set of WH headers for sale shortly and give the BC headers a shot. At this point factory exhaust manifolds are starting to look better and better.

Jamie
 

Butros

New Member
Joined
May 31, 2010
Messages
39
I just finished my 4r70w swap last summer. I'm running one of the first sets of WH shorties to be shipped way back around 1997. I ran into some slight clearance issues between the bell housing, the frame rail, and the trans dipstick. To make everything work, I ended up running a lokar flexible dipstick, swapping the motor mounts to the extreme mounts, and doing just a little grinding to the flange. It might have been possible to get the header bolted up with the engine and trans out of the truck, but the clearance was too tight to get the trans to bolt up. Once the header was removed, the trans went in without a problem, but the header did not want to go back in without gaining a little clearance.

Mike
 

rcmbronc

Contributor
Bronco Guru
Joined
Dec 15, 2003
Messages
2,778
Loc.
Tomah WI
Any more news on the header fit? I like the ball & Socket of the WH headers but dont really want a flexible transmission dipstick but may be able to live with it. The BroncoHut headers look like they will fit but they are flat flange which are not my preferred over the ball & Socket.

Any one else have an opinion?
 

needabronco

Bronco Guru
Joined
Jul 2, 2004
Messages
6,411
Loc.
Prescott/Farmington
I run an AOD with WH headers with no issues. The trans did come out of another Bronco and had some slight clearancing (grinding) on one side for the header. I'm using stock dipsticks on mine. The 4R70W that I have looks very similar to the AOD.
 

Lon L

Full Member
Joined
Jul 19, 2015
Messages
254
That's with a 4R70 auto trans Lon? Same dipstick location as Halfcabs?

Thanks

Paul

Paul, sorry, I missed this earlier. Yes I have a 4R70W with a column shifter on a 97 Mountaineer 5.0, Sanderson Headers and Bronchohut exhaust. 2 inches of Body lift and 2.5 inches of suspension lift.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,620
Loc.
PNW
I'm running a 351W w/a 4R70W, a stock AOD dipstick with BC Bronco's 1 5/8" shorty headers. Headers fit great, fit flat on the head, bolt heads have clearance on the primary tubes but no room for my Stage 8 fasteners...

The headers cleared the bell housing w/o issue but I had to clearance the AOD dipstick out of the way a little... I did not want to spend a hundred bucks on a Lokar dipstick... so a little bending of the mounting tab and I'm good to go...
 
OP
OP
67 Halfcab

67 Halfcab

Full Member
Joined
Nov 20, 2011
Messages
251
Brian, do you think there would be any more interferance between the transmission dipstick tube and headers with a 5.0 vs. 351?
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,620
Loc.
PNW
Since the "attachment strap" on the AOD dipstick mounts to the bellhousing bolt I believe you wouldn't have any other issue. Should be some slight heating/bending and be good to go.

FYI, the other nice thing is that it doesn't leak or weep any oil either. If you you'd like to dress it up a bit, powder coat the handle...
 
Top