• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Switch IAC on and off ?

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
I have the efi from a 90 mustang on my eb

Currently have the IAC unplugged because I can't stand the hanging idle

When you take your foot off the gas it's about two seconds before the rpm drops

Anyone know which of the three wires on the iac i need to run thru a switch ?

Or should I just experiment by taking one loose at a time ?
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
If it's hanging, something is wrong. You can put a toggle on route to the IAC from Pin 21 in your 60 pin EEC connector. It's usually white with light blue.

Did you run the full procedure to set base idle?
1) Disconnect IAC
2) Set idle at 750 rpm (cycle throttle to natural position)
3) Set TPS within 5% of .97 volts (green and black wire while hooked up)
4) Turn on headlights, shut off engine, and disconnect battery
5) Wait 10 minutes
6) Plug in IAC, then reconnect battery, and shut off headlights.
7) Problem should go away unless there are other issues Vacuum leak, bad component, bad wiring......
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
IAC only has 2 wires. You are probably looking at the TPS with 3 wires (orange, green, black?).

You probably have the airflow screw jacked in to get a higher idle. The ECM is reading a throttle position above idle, thus you are in a cruising logic and not idle logic and that gets you a hanging idle. Correctly fix the EFI and not do a butcher repair.
 
OP
OP
R

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
I've already tried every thing possible to get it to work correctly and it just won't

Not gonna waste any more time or money on it when a simple switch will cure it

Correct about the wires. Only two
 

brianstrange

Bronco Guru
Joined
Nov 22, 2011
Messages
1,626
Replaced it twice

Are you getting any codes?
When you replaced it, did you follow the step by step above, including disconnecting battery with headlights on etc....? If you don't you can replace it 100 times, and it won't matter. What are you getting for vacuum at idle?
 
OP
OP
R

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
No codes

I assume it's a emission thing since my 07 company truck does the same highly annoying thing even though it's an automatic

But when I bang thru the gears I want the rpm to drop instantly when I lift off the pedal
So I can hit the next gear
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
What EEC do you have? And do you run a VSS?

Not entirely sure what you mean by a "hanging idle" but the Auto EECs apparently have that programmed in. The name of that "feature" escapes me at the moment. But I believe you can do away with that by disconnecting the VSS. Mine does it and was a bit of an irritation for the first several years, but I don't even notice it anymore.

Edit: Dashpot??? Is that the name of it??? This causes the idle speed to idle at about 800-850 RPM until I come to a dead stop. Then it drops to 650ish. I run an A9P which is an Auto EEC. My understanding is the manual EECs don't have that feature. But it can be programmed out!

I kinda like the EEC controlling the idle speed. If I'm trying to start moving up a hill, as I let out the clutch I can actually feel the IAC try to get the idle speed back up to the 650ish setting. One of these days I'm gonna try putting a switch on the A/C input to the EEC to raise the idle up a few more RPM. It would be a shame to cut out these functions by eliminating the IAC.
 
Last edited:

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
My idle doesn't hang but it does not drop off to nothing as quickly as the old carb did. It settles in at about 800-850.

My SN95 EFI acts very much like the 95 GT I once owned. Heck, it rumbles the same way too.

Tim
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
800-850 is high. Properly adjust the idle and not just crank it up it will probably work just fine.

Also the IAC is directional, but will bolt on either way. Some people flip it around for clearance or what ever reason and they don't work right flowing backwards.
 

mtxride

Full Member
Joined
Jun 14, 2009
Messages
157
Loc.
San Antonio
What rpm does it "hang" at? I have a manual trans computer. When coasting to a stop with the clutch in, the engine will drop to about 900 rpm. Then as soon as I come to a stop it drops down to idle, around 700. I had a '97 manual Explorer and 2000 manual 4Runner that both did the same thing. I would also prefer it drop to idle, but I figured it was done this way for a reason, and just left it alone.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
800-850 is high. Properly adjust the idle and not just crank it up it will probably work just fine.

Also the IAC is directional, but will bolt on either way. Some people flip it around for clearance or what ever reason and they don't work right flowing backwards.

I'll have to shoot EFI_Guy a note and see what he programmed into the ECM. I have 2 idle circuits (one for A/C and one without). Using the circuit for non-A/C

Tim
 
OP
OP
R

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
What I'm talking about is when you let off the pedal. It drops very slowly. Takes almost two full seconds to drop back to idle which is around 650

It's enough that it makes it almost impossible to shift gears

I'm pretty sure I have a auto computer and I don't have a VSS
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The fact it will run with the IAC unplugged tells me the throttle is set too high. What TPS voltage are you set to? Do you even know?

With the engine fully warmed up. Not just water temp, you need the oil warm as well.
Unplug the IAC, the engine should fire on 2 or 3 cylinders and die. If it keeps running, back the throttle down and try again. Once this is set right the computer can actually control the idle, not just raise engine speed above it.

Be sure the TPS voltage is set correctly.

And while asking about setting set correctly, you do have the timing set to 10° BTDC with the spout disconnected, right? Back to the basics, get everything factory correct to start with. Now when you crank in a little extra timing you can see how that plays with the idle. Or cranking in the airflow screw can mess with the computer.
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
Edit: Dashpot??? Is that the name of it???

Correct.

Assuming you have no mechanical issues that are messing with idle then it's a function of dashpot in the PCM. I find the stock settings to be a little annoying myself and tweak them to my preference. But, what you describe sounds a little excessive.

With the IAC unplugged it should barely idle at all and almost die, the 750 mentioned is way too high, stock idle speed is lower than that (650ish). If it idles just fine with the IAC unplugged then you probably have a mechanical issue (like a vacuum leak or stop screw not set properly) that you should sort out first. You might even try grounding pin 30 on the PCM and see if it makes a difference.

The IAC is part of what makes EFI such a great upgrade (overall drivablility). If you are confident it's just dashpot messing with you then it can be tuned to your liking pretty easily.



My idle doesn't hang but it does not drop off to nothing as quickly as the old carb did. It settles in at about 800-850.

You are running my modified dashpot settings in your tune, it won't drop instantly but shouldn't hang enough to be annoying. You should be idling closer to 700-750ish
 
OP
OP
R

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
How do I modify the dash pot setting ?
Send it to a programmer along with a pile of $$$ ?
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
You are running my modified dashpot settings in your tune, it won't drop instantly but shouldn't hang enough to be annoying. You should be idling closer to 700-750ish

Guess I'll have to go through the process of setting the IAC and look for a vacuum leak maybe. The 800-850 idle is not really an issue so I'll get to it at some point. Rig runs great.......

Tim
 

EFI Guy

TheEFIguy@gmail
Joined
Apr 14, 2013
Messages
1,168
Loc.
BFE
How do I modify the dash pot setting ?
Send it to a programmer along with a pile of $$$ ?

No need to send the PCM out, chips are easy to install. I do a mail order Mustang chip for $220 shipped, it holds 2 tunes that you can switch on the fly. I just recommend making sure there is no mechanical issue first. Don't spend the coin unless you are confident it will fix your problem.

Guess I'll have to go through the process of setting the IAC and look for a vacuum leak maybe. The 800-850 idle is not really an issue so I'll get to it at some point. Rig runs great.......

Tim

There are a ton of different factors that the PCM uses to determine desired idle speed so you may not have an issue at all. But if it never drops below 800 I'd say something is going on.
 
Top