• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wheel Spacers . . . . Add to check list

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Throwing this out there that if you use wheel spacers you should check them from time to time. I realize this will probably create a storm of comments on why you shouldn't run spacers, but so be it, get after it. Purpose here is to make aware. Mine were about 6 years old and I just recently found that 2 of them had cracks at the mounting points, where they mount to the vehicle. One was on front and the other on the back. These are 1.25 spacers. I replaced them but now know I should look at them on occasion.
 

Attachments

  • IMG_8775.jpg
    IMG_8775.jpg
    102.5 KB · Views: 354

Bronco Junkie

So Cal Broncos
Joined
Feb 29, 2012
Messages
3,246
WOW! I was just worried about mine coming loose. Think they were made in the USA? HAHAHAHA!! Made in China!
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
if those are aluminum that would be the problem. if you are going to run spacers then only use steel and also the ones that bolt to the hub with the lugs and have new lug studs on them. do not use the aluminum spacers that you need longer studs to install. those spacers are dangerous!!
 

Bronco Junkie

So Cal Broncos
Joined
Feb 29, 2012
Messages
3,246
All of the Bronco vendors that do carry wheel spacers only carry billet aluminum ones.
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Those are the ones that bolt to the hub and then the wheel bolts to them. About the best you can buy, same as the vendors sell
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Over-torquing your lug nuts can crack them like that, as can just good 'ol fashioned hard use. That said, I wouldn't run billet aluminum wheel spacers without some sort of torque ring or pocket around the wheel studs, as it does a better job of maintaining a uniform contact stress between the mounting surfaces and maintaining wheel torque.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Those are the ones that bolt to the hub and then the wheel bolts to them. About the best you can buy, same as the vendors sell

Thanks for reminder JW.. add it to my checklist for OCBR
 

agboy91

Full Member
Joined
Aug 29, 2013
Messages
214
Loc.
Bishop, GA
I noticed my wheel was wobbling and pulled in to the tire shop thinking I had a tire out of balance. Turns out my studs were tool long and hitting the rim not allowing it to sit flush on the spacer. I also noticed my spacers were cracked too. I took them of and they broke in three pieces. This was a close one. Is there a torque spec on the aluminum spacers? I think I over torqued mine. Check your out.
 

Attachments

  • IMG_0075.jpg
    IMG_0075.jpg
    82.7 KB · Views: 128

KyddsPly

Sr. Member
Joined
Nov 30, 2012
Messages
941
90 ft lbs for aluminum spacers, star pattern of course.


Sent from my iPhone using Tapatalk Pro
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I've seen alloy wheels split the same way.
It goes to reason, if you tighten the conical nut into it's seat too much, something is going to give.

It's very easy to over torque a lug nut. Impact wrenches without a torque adapter can easily run the nuts up to 150 ft lbs.

I've seen tire shops that use a torque wrench after they had already over-tightened the nuts with the impact. ?:?

I use an "X" tire wrench and an old bender beam Craftsman torque wrench with a ratchet adapter when putting on my wheels. The old torque wrench may not be stylish or extremely accurate, but it makes sure the nuts are tight enough without distorting things.
 

Attachments

  • IMG_20170901_125149750.jpg
    IMG_20170901_125149750.jpg
    68.7 KB · Views: 87
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Which ones are you going with JW?



Same as I had. I had bought 2 sets but since the white Bronco wasn’t finished unused a couple from it. Bought another set to go on it. Just need to check them periodically
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I've run 1 to 1.5" spacers on many rigs for many years without the first problem. But nearly all of them are steel too.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
This is a huuuuuge deal on jeeps. Recommend pulling and checking them every 3 months maximum, less with hard use. Also for the cost of rims which have the offset you need, it makes this a non issue.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Same as I had. I had bought 2 sets but since the white Bronco wasn’t finished unused a couple from it. Bought another set to go on it. Just need to check them periodically

From where again? I got 2” ones. Couple of em replaced lugs. Just don’t seem to work as well so planning to pick up a couple new ones probably
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
From where again? I got 2” ones. Couple of em replaced lugs. Just don’t seem to work as well so planning to pick up a couple new ones probably

I think all on ebay, the set I bought this summer came from eBay, the first 2 sets I can't remember but they were the same.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
if those are aluminum that would be the problem. if you are going to run spacers then only use steel and also the ones that bolt to the hub with the lugs and have new lug studs on them. do not use the aluminum spacers that you need longer studs to install. those spacers are dangerous!!
They're all dangerous to some degree. Road racers use shim spacers to tune the car's handling. Steel there is perhaps desirable, but not an absolute. Steel in an off-set stud type spacer should be an absolute, but people are cheap.

All of the Bronco vendors that do carry wheel spacers only carry billet aluminum ones.
Aluminum is easy to machine and easy on the machine tool. Steel is none of that, but when you find an OEM spacer (like on the front of 4WD Dually's) they're always steel or semi-steel. For a good reason called fatigue life.

I noticed my wheel was wobbling and pulled in to the tire shop thinking I had a tire out of balance. Turns out my studs were tool long and hitting the rim not allowing it to sit flush on the spacer. I also noticed my spacers were cracked too. I took them of and they broke in three pieces. This was a close one. Is there a torque spec on the aluminum spacers? I think I over torqued mine. Check your out.
Been saying this exact fatigue failure is going to happen for years. Been told all of those years that I'm Chicken Little. If you can visualize the stresses on that part the failure mode is really easy to see. This is far from the first such failure that I've seen posted. Couple guys over on the IH8MUD forum have experienced "religious conversions" when theirs failed. One had his go away at speed on a freeway.
 

RPM289

Sr. Member
Joined
Jan 4, 2008
Messages
835
What is the thickest ones to run? I need to space my 38 out to get a little more turning radius.
 
Top