• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Suspension question

rspd505

Jr. Member
Joined
May 3, 2016
Messages
147
Loc.
Rising Sun, IN
Haven’t really dug into this much, just thought I’d throw this out there to you guys. Is there a easy way to lower the Bronco to make it easier for someone to get into it? Like an air ride or something similar? Without costing a small fortune. It wouldn’t need to be slammed like a low rider, but would need to drop about 8-10 inches, then raise back up to normal ride height. My wife has didficulty due to a stroke. My suspension is all stock now. My plans are to go with possibly a 29-30” tire. Body is uncut.
Thanks
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
Air ride is not out of the question. The front could be kind of cheap. Replace spring with air bag, the rear could be a little more complicated.
The other thing is dropping 8 to 10 inches is an awful lot. May have to compromise at about 5 or 6 inches without something more custom being done.


Sorry about your wife's condition.
 

rguest3

Bronco Guru
Joined
Dec 13, 2012
Messages
3,780
Would AMP Research steps on the sides be an option? They steps are electric and lower down for use when the door is opened.

They may be 6-8 inches lower than original step in height???

North East Classic Ford Parts has the brackets and uses an AMP step for a Ford Pickup.
 
OP
OP
rspd505

rspd505

Jr. Member
Joined
May 3, 2016
Messages
147
Loc.
Rising Sun, IN
Would AMP Research steps on the sides be an option? They steps are electric and lower down for use when the door is opened.

They may be 6-8 inches lower than original step in height???

North East Classic Ford Parts has the brackets and uses an AMP step for a Ford Pickup.

Probably not. My Dodge has running boards and they do not help her at all. She needs to go from a standing to a sitting position. Stepping up doesn’t work so well. I have thought of something like that though.
 
OP
OP
rspd505

rspd505

Jr. Member
Joined
May 3, 2016
Messages
147
Loc.
Rising Sun, IN
...The other thing is dropping 8 to 10 inches is an awful lot. ...

Sorry about your wife's condition.

Maybe I need to re think this. Instead of lowering the Bronco, raise her up. A portable lift, like a scissor jack platform or ATV lift. Something that is light enough to throw in the back, but has a big enough surface to be stable.

Thank you, she is doing fine. It happened almost 12 years ago, two weeks after the birth of our daughter. She has overcome a lot and I am trying to give her back as much normalcy as I can. We used to go cruising in my old Heep before this happened and she loved it.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
what top you runnin. if no top then you get one of those cherry picker crane things for the bed of a truck. they look like an engine hoist mounted to the inside rear corner af a truck bed and swing out to lift heavy items up into the bed. but anyway, install one of those right behind the driver seat and put a seat in it. then just crank her up and swing her in. hope i painted a clear enough picture. :)
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I think you could come close to doing it with airbags. biggest issue is you wont be able to go down but 7 in in the front and 6 in the rear when fully deflated as that's about the measurements of stock height from top of axle tube to bottom of frame.
You may consider modifying the pass side floor by lowering to the bottom of the rocker panel or maybe to the bottom of the frame then installing a custom seat possibly on a air bag as well so it can be lowered to get in and out then raised to see out the window at a normal height. that might get you where you want to be. Might only need to modify the area under the seat so you can lower it and still have the floor board at normal height.
 

76YETI

Contributor
Sr. Member
Joined
May 27, 2015
Messages
932
Loc.
KC METRO
How about a ramp with platform you can drive up to. Have the platform just high enough to clear the door swing. Load her up, cruise and then come home and drop her off...like a loading dock?
 
OP
OP
rspd505

rspd505

Jr. Member
Joined
May 3, 2016
Messages
147
Loc.
Rising Sun, IN
How about a ramp with platform you can drive up to. Have the platform just high enough to clear the door swing. Load her up, cruise and then come home and drop her off...like a loading dock?

I built something like that on the deck I built off the back of the house. I used the landing of the wheelchair ramp, that was built specifically to be the right height for her to get in the Heep. I put a section of the railing on hinges to make a gate. The idea was to pull up next to it and she get in. That worked one time until she got spooked because she was afraid she would fall. Her vision was also affected by the stroke, I can’t even imagine what that would be like.
 
OP
OP
rspd505

rspd505

Jr. Member
Joined
May 3, 2016
Messages
147
Loc.
Rising Sun, IN
I’m actually leaning toward something like this. It would be portable and could be used for other vehicles. I would make the base and platform probably 2’x2’ so it would be stable.
 

Attachments

  • D621667B-8E06-4FB5-9544-171943BBC300.jpg
    D621667B-8E06-4FB5-9544-171943BBC300.jpg
    53.9 KB · Views: 31

Skiddy

Bronco Guru
Joined
Oct 8, 2003
Messages
11,587
I’m actually leaning toward something like this. It would be portable and could be used for other vehicles. I would make the base and platform probably 2’x2’ so it would be stable.
that would probably work as long as its light
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Carry a cordless dill with the right socket on it as well, and you could get the thing up and down reasonably quick too I would think. Since it's a screw type, it's likely "geared" pretty low. A hand ratchet would get the job done, but might take awhile.

Paul
 
Top