• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

C-4 modulator retaining clip

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I'm not an auto trans guy..period. This is my first EB with a C-4, even though I've owned more than a dozen EBs. So I have an excuse for why the modulator was spit out of the trans upon the first startup of the new build..followed on to the shop floor by a bunch of tranny fluid..:-X

OK..so now that I've realized that the modulator needs that spring retainer thingy that I found a picture of with my googler, and after hours of rummaging through the piles of parts and finding nothing remotely resembling that little rascal....where does a feller buy one?
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, if I had any I would send you one. Make sure the pin is still there when you put it back together. Good luck
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
If I remember correctly the non-HD version has the same clip as do possibly the C3's(?) in Pintos and Mustang II's.
So it should be out there and more prevalent than a lot of our eb parts.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919

Attachments

  • IMG_5509.jpg
    IMG_5509.jpg
    52.5 KB · Views: 91
OP
OP
bmc69

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Hi, if I had any I would send you one. Make sure the pin is still there when you put it back together. Good luck

found the pin lying in the middle of the puddle....thanks! ;)
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
I have an extra if you don't find one... just PM me with an address.

I recently installed a trans-brake in my racer which did two things - it obsoleted the modulator and free'd up a bracket because I had to fabricate a new design so I could install my trans-brake solenoid into the modulator hole

Just let me know


DJs74
 
OP
OP
bmc69

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I have an extra if you don't find one... just PM me with an address.

I recently installed a trans-brake in my racer which did two things - it obsoleted the modulator and free'd up a bracket because I had to fabricate a new design so I could install my trans-brake solenoid into the modulator hole

Just let me know


DJs74

Appreciate the offer! Looks like JBG has me covered.
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
Also meant to say I've used zip ties in lieu of a bracket to do the job. I place one zip tie around the port of the modulator (over the hose) and then zipped tied that one to the line on the side - worked fine.

The seal on the modulator is a piston seal or static seal, meaning it does not require any specific force of the modulator against the case to make the seal. The seal takes place in the bore of the case and on the shaft of the modulator. The bracket simply holds the modulator in the bore - does not apply any pressure to make the seal - so a zip tie will work in a pinch. Slightly on the donkey side as far as looks but works fine otherwise.


DJs74
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Bill,

I left Pax River back in '95. There used to be an awesome transmission shop on St. Andrews Church Road called Driveline. Are they still there? If so, that is where I would look.

Roger
 
OP
OP
bmc69

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Bill,

I left Pax River back in '95. There used to be an awesome transmission shop on St. Andrews Church Road called Driveline. Are they still there? If so, that is where I would look.

Roger

The business is still there, but... partners Berg and Jim sold it to another feller, Kirk, who owned a paint and body business. Kirk put up a huge shop building behind the original one that you were familiar with. Eventually, not only did Berg and Jim leave, all their other ace trans and driveline mechanics left too. Kirk was killed in a car accident a few years ago and so now there is nobody left that I know and the place is mostly just a body and paint shop with used car sales out front.

The NP-435 in my '78 Bronco was built by Jim at Driveline. Around 1993 I believe it was. ;) Back when they raced the dirt drag monster "Hot Tuna", towed around to races with their custom Suburban with it's trick paint job and the name "Tuna Helper" on the doors. Good times...
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
T
The NP-435 in my '78 Bronco was built by Jim at Driveline. Around 1993 I believe it was. ;) Back when they raced the dirt drag monster "Hot Tuna", towed around to races with their custom Suburban with it's trick paint job and the name "Tuna Helper" on the doors. Good times...

That sounds like good old times. Hot Tuna and Tuna Helper. Too Funny.
 
OP
OP
bmc69

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
That sounds like good old times. Hot Tuna and Tuna Helper. Too Funny.

I tried to find some pics in my archives..came up empty. Hot Tuna was a serious sand drag machine with an alcohol-fueled blown aluminum Keith Black hemi.

Good times. I was racing my '72 EB on the MX tracks at the same venues back then and losing regularly but with style. And Neil Welch was dominating the mud bogs with his evil EB. We were all good friends.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
One thing I have learned. Time steals away good friends. It's good to remember these adventures.
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Thanks Bill. I did not know the Driveline guys personally but I did see plenty of their work. They were certainly masters of their professions back in the day.

Never attended dirt drags but I spent most summer weekends when not on duty at MIR. I'll have to dig some old photos and post them.

The business is still there, but...
 
OP
OP
bmc69

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
Thanks Bill. I did not know the Driveline guys personally but I did see plenty of their work.

Did you see any of the AC Cobra replicas that Jimmy Mills built? A couple of them were insanely powered..;D I don't know how many he built in total but he was always building one for somebody, it seemed.

Jim moved on from Driveline to work for a local marine fabricator - he was an incredibly skilled aluminum welder/facbricator too - but he suffered a massive heart attack about 10 years ago. He recovered but he also retired.
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Did you see any of the AC Cobra replicas that Jimmy Mills built?

No, I do not remember those. I lived in the barracks on base from Jan 85 to Dec 88. One of my buddies, Doug, had a mid 70's Monza with a 350 LT1 shoehorned between the fenders. One of the Driveline guys fabbed/installed a 14 point cage, tubbed the chassis, and shortened the 12 bolt. Doug then installed a set of super fat Mickey Thompsons. The car was street legal and as far as I know, no one ever beat it in a drag race. It was a blast to drive.
 
Top