• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Starter relay for running Fitech

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
I'm building a dashboard of sorts so I can start and monitor everything with the body off. I bought a starter relay at autozone but I got home started reading the paper in the box. It says DONT USE THIS STARTER SOLENOID WITH ENGINE CONTROL COMPUTER. THIS SOLENOID DOES NOT USE SUPPRESSION DIODES..USE WILL RESULT IN PERMANENT DAMAGE TO COMPUTER...

Ohhh kkkk... SO what solenoid do I need since I'm going to install FITECH? Please and thankyou
 

Attachments

  • 20180513_114630.jpg
    20180513_114630.jpg
    70 KB · Views: 118

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Put a diode in and call it done. Goes from the "S" post to ground. Polarity matters. Correctly you can't tell it is there. Backwards and it is a short to ground.
 
OP
OP
Builtnotbought0

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
Put a diode in and call it done. Goes from the "S" post to ground. Polarity matters. Correctly you can't tell it is there. Backwards and it is a short to ground.

You sound like you know what your talking about...and I have no idea what your talking about..LOL..do you have an illustration for dummies?
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Broncobowsher,

Wouldn't using a Starter relay from say an 1996-2001 Explorer/Mountaineer accomplish the same thing? Since Ford EFI motors have a diode built in the relay....
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Stolen from Stangnet.com See thread for full info...

https://www.stangnet.com/mustang-forums/threads/diode-in-starter-solenoid.899300/

The diode is a cheapy, easy thing to add. Use a 1N4004 or 1N4005 available from Radio Shack or other electronic suppliers.

Using a diode as a dampener in automotive circuits:

Theory of operation:
The diode acts as a surge absorber or one way gate. Anytime you turn the power off an inductive load (coil, motor, solenoid, etc) the collapse of the magnetic field creates a voltage spike of opposite polarity to the voltage applied. The positive wire sees a negative spike and the negative wire sees a positive spike. The diode is wired backwards so that it does not conduct during normal forward operation. When the magnetic field collapses, the diode sees the reverse polarity spike and clamps it. This prevents the spike from possibly damaging the rest of the electronics in the car.

When used to clamp spikes in automotive circuits, connect the lead that comes from the end of the diode that has the band on it to the positive side of the circuit. Connect it the other way and you will make smoke.


A properly functioning diode will measure very high resistance or open circuit in one direction. Reverse the meter leads and it will measure a lower resistance.


Attachments
Diode markings.GIF
Diode markings.GIF
9.8 KBViews: 16
 
OP
OP
Builtnotbought0

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
Stolen from Stangnet.com See thread for full info...

https://www.stangnet.com/mustang-forums/threads/diode-in-starter-solenoid.899300/

The diode is a cheapy, easy thing to add. Use a 1N4004 or 1N4005 available from Radio Shack or other electronic suppliers.

Using a diode as a dampener in automotive circuits:

Theory of operation:
The diode acts as a surge absorber or one way gate. Anytime you turn the power off an inductive load (coil, motor, solenoid, etc) the collapse of the magnetic field creates a voltage spike of opposite polarity to the voltage applied. The positive wire sees a negative spike and the negative wire sees a positive spike. The diode is wired backwards so that it does not conduct during normal forward operation. When the magnetic field collapses, the diode sees the reverse polarity spike and clamps it. This prevents the spike from possibly damaging the rest of the electronics in the car.

When used to clamp spikes in automotive circuits, connect the lead that comes from the end of the diode that has the band on it to the positive side of the circuit. Connect it the other way and you will make smoke.


A properly functioning diode will measure very high resistance or open circuit in one direction. Reverse the meter leads and it will measure a lower resistance.


Attachments
Diode markings.GIF
Diode markings.GIF
9.8 KBViews: 16

Thankyou...but how would I know when the diode is bad? I won't know until I smoke my computer for the FiTch? Wouldnt it be better to have a starter relay that just fails? Would the relay for the explorer setup just fail when its bad?
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Assuming this is what Fitech is asking for...

If the diode failed, you would have no way of knowing it did... And I assume if it did, it would not have any affect on the operation of the starter relay.

Maybe someone brighter than I will chime in on this...

But I have reused Explorer relays with 100K+ on them in 3 EDIS conversions without issue?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I was saying to just add a diode to the parts you already have. What was said above is right. In theory you should do this to every relay in the truck.

I have seen one fail once (or maybe the wrong part was put in). Electric cooling fan would cycle. Every time the fan turned off the engine would stumble. Didn't hurt the computer. Just caused a little interference for a moment that confused the computer.

In general it is a non-issue. But sometimes it can be. So that is why it is put in the instructions, to cover the times where it is an issue. And won't hurt on the non-issue vehicles as well.
 
OP
OP
Builtnotbought0

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
So I went back and had them pull a 2000 explorer starter relay. No paperwork warning me not to use it without a diode....and the one for a 2000 explorer says DIODE SUPPRESSED on the back...will this work???
 
OP
OP
Builtnotbought0

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
I was saying to just add a diode to the parts you already have. What was said above is right. In theory you should do this to every relay in the truck.

I have seen one fail once (or maybe the wrong part was put in). Electric cooling fan would cycle. Every time the fan turned off the engine would stumble. Didn't hurt the computer. Just caused a little interference for a moment that confused the computer.

In general it is a non-issue. But sometimes it can be. So that is why it is put in the instructions, to cover the times where it is an issue. And won't hurt on the non-issue vehicles as well.

I would hate to fry something in the fitech since I have to save up for a month just to buy this one...do you think the relay I stated in my last post would work?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yes that will work. That's the point of the diode in the factory units sold after computers came into use. You'll see that type on all Fords since the later '80's most likely.
They didn't make a big deal out of advertising it because they weren't making them for "conversions" but just expected to be used in the proper applications.

Plenty of people out there (many members here in fact) still running stock, older style starter relays without diodes and not having any trouble. But the warning is valid and those others may just be living off borrowed time.
No reason to warn anyone away from using diodes on an already diode suppressed relay since it's never been an issue. So don't concern yourself over a lack of a warning.
Nobody expects you to add your own, or if you did, it probably wouldn't hurt anything anyway.

But rather than roll-yer-own with your dash panel, just use the new style relay (sounds like you are?) and make sure you use that type in your Bronco when it's all back together.
Avoid the trouble and the concern all together. If it's good enough for a factory computer, it should be good enough for an aftermarket computer.

Paul
 
OP
OP
Builtnotbought0

Builtnotbought0

Full Member
Joined
Sep 24, 2017
Messages
156
Loc.
Belen NM
This is the one I got with the internal diode...does it look familiar to anyone? 2000 explorer??
 

Attachments

  • 20180513_203357.jpg
    20180513_203357.jpg
    63.9 KB · Views: 116

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Try, just about anyone with a late '80's and newer Ford of any description.;);D
Ok, so there may be some variations on the theme for different rigs, but that same basic relay has been used in so many applications it's pretty ubiquitous.

Many of that "pancake" style will have only three studs though, as an "I" contact point was no longer needed by the time they came into use.
Are there any letters or other indicators by the two smaller studs?

I think I see "I" and "S" but not sure.
You'll be using the "S" though, and they all have that. The S wire (Red w/blue on the stock harness) is the one that energizes the relay to crank the starter.

Paul
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
I bought the HD one from O'Reilly's, the body is a different color but it looks the same.

I think you will be fine, you are over thinking this...

Not sure what surface you have mounted the relay to by the picture, but if it is fiberglass the metal body of the starter relay needs to be grounded.
 
Top