• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Question on stock Bronco Height

Maddog B

Jr. Member
Joined
Mar 12, 2018
Messages
88
This is my first post here after working on my grandpas 1972 Bronco for a few months. I've read on multiple post that a stock Bronco has about 7 inches between the axle tube and bottom of the frame in the front and 6 in the rear. I measured mine and I have 8.5" in the front and 8" in the rear. everything looks stock to me. The rear does not have any blocks and the front looks 100% stock. Is there a way to tell if the front coils have been changed? I was going to put a 2.5 suspension lift eventually but I may just leave it the way it is. Grandpa always ran 31x10.5's on stock wheels as far back as I can remember and thats what I'm putting back on it. I know if it ain't broke don't fix it, but I'm about to replace the C bushings and i'de like to have an Idea if it's already lifted while I'm tearing it apart. This site has been a tremendous help and I'm glad to be a part of the Bronco community.
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
How many leafs are in the rear springs? From the pictures in your garage it does look to sit a little higher than stock. Any pics of the suspension?
 
OP
OP
Maddog B

Maddog B

Jr. Member
Joined
Mar 12, 2018
Messages
88
There are 7 leaves on the rear. You have to forgive me but I'm still trying to figure out how to post pics. Those are 31x10.5 in my garage pics. I'll upload the pics in my garage.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I know if it ain't broke don't fix it, but I'm about to replace the C bushings and I'd like to have an Idea if it's already lifted while I'm tearing it apart. This site has been a tremendous help and I'm glad to be a part of the Bronco community.

Generally speaking, if you're going to have power steering then go with added caster angle even if you're not lifted. So as long as your pinion angle permits (and most do without a problem) put as much C-bushing in as you can tolerate.
The perfect answer is to check your caster before ordering bushings. But since yours is already apart it's not like you can just go down to the local alignment shop and get a readout. So you can either figure out how to measure what you have (kind of finicky, but probably something that can be done), or punt.
With your minimal lift I'd still go with at least the 4 degree bushings, unless you're going to stick with manual steering. In which case I'd stick with 2 degrees.

Your rear springs have been modded slightly. Hard to tell just exactly what's going on, but I'd say you have an add-a-leaf and then that clamp thingy holding the leaves at an odd angle.
Most add-a-leaf kits were designed to lift between 1 and 2 inches (1.5 common) and that is right about where yours is.

Hard to tell anything about the fronts though. I suppose measuring the wire diameter of the coil and comparing to a known stock coil would work. But I don't have the stock measurement handy, so maybe someone else can provide that?
Your GVWR seems to indicate a 4300lb capacity, which I think was the lighter setup in your year(?) so that 7-leaf pack would have been a 5-leaf pack originally. If so, then there may be two additional leaves. Perhaps though, I'm remembering incorrectly and the 4300 is the heavier of the two and would have had 6-leaf packs.

Anyway, that's a start. Others will have things to add that might help you better.

Paul
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
It looks like you definitely have a lift. The stock suspension used a 5 leaf pack. The HD suspension used a 6 leaf pack. Your glovebox tag indicates a U150 4300 lbs suspension which is the standard duty(base) package. It looks to me like you have an add a leaf and possibly a heavier overload spring added as well. The front coils look to have been swapped out to match. So, it looks like you have the 2" lift you suspected.
 
OP
OP
Maddog B

Maddog B

Jr. Member
Joined
Mar 12, 2018
Messages
88
Thanks guys for the response. Any suggestions on the rear leaf springs as far as keeping them the way they are? Some of the leafs have shifted out of alignment and I didn’t know if that was a big deal. I know as long as the pin doesn’t break then they should stay put but I don’t want some catastrophic failure due to something being bound up. Maybe the best bet is to just get some new 2.5 springs but I’m torn with just trying to get on the road.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
When springs wear on each other, sometimes it's uneven and just the motions of moving and flexing will eventually fan out the leaves. The more the variations, the quicker they fan out.
First make sure that the center pin is tight. They can loosen up over time and let things get out of hand more quickly.
Of course, make sure that the u-bolts are fully torqued to spec too. Unfortunately in your case, those original looking u-bolts may literally snap if you loosen and re-torque them. Even if you just re-torque without loosening it can happen. But it's still worth the trouble to make sure things are as-specified. Clean them and lube them, and maybe due to the fact that they've been removed at some point in their past (to add the leaves) they will cooperate. Maybe....

If leaves continue to fan out, you can buy small inexpensive spring clamps that mostly float and don't literally clamp the leaves tight like the one I see in the pic.
Ultimately new leaf packs are going to be the best route. But that doesn't mean you can't get more life out of the old ones. Might not be as happy a life, but your wallet will be happier.

Even before that, if you're not unhappy with the overall ride quality (if you are though, you're a tough old-truck kind of person!), you can still refurbish the old leaves. New bushings, new u-bolts, clean, smooth rough and grooved areas on the individual leaves, and re-paint and they're going to work at least half-way decently for years to come.

Good luck.

Paul
 
Top