• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley Carb setup

72_EB

Contributor
66to77
Joined
Feb 4, 2003
Messages
4,982
That's a stock fuel pump you have on there now. It won't put out 8 psi, they are more like 4-6 psi if working properly. 8 psi is pushing it with a stock setup and carb for putting out too much pressure.
Why do you want to change the pump? What's the issue?
The pump to carb lines could use some attention improvement, but you might have some other issues going on here.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
That's a stock fuel pump you have on there now. It won't put out 8 psi, they are more like 4-6 psi if working properly. 8 psi is pushing it with a stock setup and carb for putting out too much pressure.
Why do you want to change the pump? What's the issue?
The pump to carb lines could use some attention improvement, but you might have some other issues going on here.

I don't know the PSI on the stock pump but when I went looking for OEM replacements at your typical parts stores they were 8 psi. The reason I'm looking at replacing is that my bronco runs like crap. It will run ok in first gear then worse in second gear and third gear it's really bad. What it does is it progressively gets worse through the gears and it feels like its starving for fuel, it bounces between fast and slow then back again and then bogs down when I try to climb a hill. My thoughts, and I'm far from a mechanic, are that the fuel pump may be going out or this may be a product of too much fuel since the stock pump I thought was 8 psi is too much for the aftermarket carb and I don't have a fuel pressure regulator installed. Also, I noticed it would be worse on my main tank and not bad on my reserve tank. I then noticed a leak on my sending unit of the main tank which I've now replaced with a M1A1 tank. Now it appears that the problem is worse and it happens to both tanks.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
f8ddabd010147f2928cca114a13e6492.jpg
f79b5b284cc338bfe35a9b31292d016b.jpg
4b25112477b6672c67433a9e812c9db6.jpg
14b373906d4c1e9a7a03c6d7a2b465bd.jpg
3a44fff478a937dc07f915826f437f0c.jpg
b79c2f5fc0937567b7642ff712ccee51.jpg
1c19ab1e9888d0c928b69ab2c8deefd3.jpg
a80290e120feae9add41a6340d736d09.jpg
52d6ab696b28cf52301a45bd044dc32d.jpg
d18cdef35b616d7f485fd76f195bdba9.jpg
e0f0215a2f0e020764be3069e3e9f2b8.jpg
e9b0fcfb4c45036c6634fd7d9b6bff86.jpg
2b03ff1ea5732e48f4bf2e4966b7d911.jpg



Sent from my iPhone using Tapatalk
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, I'm not understanding what runs worse means.
Does it ever pop and backfire, or seem like it is running out of fuel? Does it lose power?
The ignition, including ignition timing needs to be set up first. Most guys like to advance the base timing beyond factory specs.
Do you know which carb you have?
Do you know what cam you have?
Can you use a vacuum gauge and post the vacuum reading?
The pcv valve should be hooked up to the back of the carb, on the red plug port. The single intake runner is not suitable for pcv because that cylinder will run lean.
Be aware that aluminum intake manifolds are know to have a vacuum leak between the underside of the manifold and intake port.
Good luck
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Have you checked your timing , do you know what size jets are in your carb { road Warrior ?} do you know what cam ? -it that a single plane intake manifold ?
Like B RON CO suggested ; I'd move the connection for your PCV and your power brake booster. Also check for clearance between your throttle linkage and the line going to your booster.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
Hi, I'm not understanding what runs worse means.
Does it ever pop and backfire, or seem like it is running out of fuel? Does it lose power? It does backfire now, it also seems like its running out of fuel and worsens as I get higher in gears. It bogs down and acceleration fluctuates and will die or close to it when climbing a hill.
The ignition, including ignition timing needs to be set up first. Most guys like to advance the base timing beyond factory specs.
Do you know which carb you have? Holley Demon 600
Do you know what cam you have? Was told by PO it was a RV style cam but thats all I know about the cam
Can you use a vacuum gauge and post the vacuum reading? I dont have access to one currently
The pcv valve should be hooked up to the back of the carb, on the red plug port. The single intake runner is not suitable for pcv because that cylinder will run lean.
Be aware that aluminum intake manifolds are know to have a vacuum leak between the underside of the manifold and intake port.
Good luck

Does it ever pop and backfire, or seem like it is running out of fuel? Does it lose power? It does backfire now, it also seems like its running out of fuel and worsens as I get higher in gears. It bogs down and acceleration fluctuates and will die or close to it when climbing a hill.
The ignition, including ignition timing needs to be set up first. Most guys like to advance the base timing beyond factory specs.
Do you know which carb you have? Holley Demon 600
Do you know what cam you have? Was told by PO it was a RV style cam but thats all I know about the cam
Can you use a vacuum gauge and post the vacuum reading? I dont have access to one currently
The pcv valve should be hooked up to the back of the carb, on the red plug port. The single intake runner is not suitable for pcv because that cylinder will run lean.
Be aware that aluminum intake manifolds are know to have a vacuum leak between the underside of the manifold and intake port.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
Have you checked your timing , do you know what size jets are in your carb { road Warrior ?} do you know what cam ? -it that a single plane intake manifold ?
Like B RON CO suggested ; I'd move the connection for your PCV and your power brake booster. Also check for clearance between your throttle linkage and the line going to your booster.

When you state "I'd move the connection for your PCV and your power brake booster" do you mean swap them? So remove the PCV to manifold and change it to PCV to back of carb (where red cap is) and move the brake booster from the manifold to where?
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the brake booster is ok where it is.
The pcv should be right at the carb.
The difference is the pcv draws vacuum out of the crankcase most of the time, and the brake booster just pulls on a rubber diaphragm. The booster does not constantly "use" air. Except the booster hose may be in the way of moving the pcv hose. In that case, put the booster hose we're the pcv is, and put a plug in the manifold runner after you remove the booster line.
The 600 CFM size carb and rv cam are good for Broncos
Popping, surging under load, etc are indications of a lean condition. You could have a clogged fuel filter, stuck float, improper float level, weak fuel pump or? It could be as simple as a small crack in a rubber fuel hose.
If you want to do a quick fuel pump test you can remove the rubber hose at the carb and see how long it takes to fill a coffee can. Let a helper turn the key or use a remote starter switch at the solenoid and carefully direct the fuel into a coffee can. A good fuel pump will fill a can in @15 to 20 seconds.
Good luck
 

rmk57

Sr. Member
Joined
Feb 24, 2016
Messages
580
I would try lowering the float level and turn the mixture screw in to lean it out.
The plugs look sooty, so it's running a bit rich. I'm also not a big fan of glass fuel filters, just for safety sake.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, the little port on top of the pcv valve needs to be plugged. Put your finger over it when it is running.
Good luck
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
You guys are awesome! That worked...for the most part. You guys got me running again and made me more knowledgable. So the reason I said the most part is once I got it on the interstate and got above 60 it would start to act up again. It basically feels like once I'm over 60 someones randomly tapping the brakes while I'm trying to accelerate. If I put it to the floor it'll flatten out at 70 then if I feather the throttle back it'll get power again and go up to 80 no problem.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Id say your still running lean and probably need to rejet the carb to get that high speed performance. As was said earlier a stock pump is 4-6psi you dont need or want anymore than that. Those 8psi pumps are only good for racing where your at full throttle. On a street engine they may only cause issues with flooding because the fuel will push past the needle seat.
Another note get rid of that glass fuel filter and quick. They are not good to use on a 4wd. A few years back I came close to buying a 1974 bronco that was only on the road for 6 months if that since new. Well the guy told me he put one of those glass filters on and went down a dirt road the filter cracked against the valve cover and the bronco burnt to the ground.the tranny was a melted pile of aluminum and everything else burnable was gone leaf springs were arched the wrong way from the heat. The body looked to be in good shape but Im sure it was probably warped in spots so I passed on it.
 

taipeichris

Bronco Guru
Joined
May 11, 2006
Messages
1,753
Hi,
That's a really clean and pretty engine bay!

My 2cents, PLEASE DITCH THE GLASS FUEL FILTER. Those can go very bad, very fast. I agree, keep the stock pressure fuel pump.

Good luck!
:cool:
 

WheelHorse

Bronco Guru
Joined
Nov 22, 2004
Messages
2,511
Rich idle for sure.

Adjust your idle mixture screws in until it starts to stall. Back them out to achieve the highest idle/vacuum and then just a 1/4 turn richer (out).

Due this at operating temp. This will, at the very least, dial in your idle adjustment.

Load adjustments are most easily achieved by monitoring a wideband afr.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
Ok you guys make sense, glass filter is out! The issue I have with the idle mixture screws is that once I have it warmed up I start off at 2 full turns out then back it down till it's about to die than go a 1/4 turn out. That makes it ride nice but it never wants to start cold at that setting. I have to back the screws out just to get it to start then screw them back in once it's warmed up. Do I need to keep it at those initial settings then make adjustments to the electric choke?
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Your choke appears to be set pretty lean, so yes set your idle mixture screws to their ideal setting when hot and adjust the choke to where it fully closes when cold.

Your plugs indicate rich but until you set your idle mixture and choke correctly you won't know for sure.
 
Top