• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Twisted wedge heads

74 Bronco Billy

Contributor
Sr. Member
Joined
Jul 4, 2016
Messages
798
Does twisted wedge heads (Trick Flo 11R) make the engine wider or narrower or about the same as standard 20* heads? Do they infringe on the space for the brake master cylinder or make more room? Does the intake manifold and therefore the carburetor or efi set up sit higher than 20* heads?

Thanks,

Forrest
 

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
No, i have them on my 66 mustang with a 347. I dont think the hieght is effected at all. You will most likely be running roller rockers with them which do to whatever lift cam you run, assuming it will have a higher lift, you may neednto run a higher taller valve cover.
This is what happened with the with my cutrent bronco set up. The only problem was the wire harness that exits the firewall behind the diverside valve cover. It super tight but did clear.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I think the valve cover flanges are a little taller. With a 351 I could not run the Ford Motorsports tall valve covers because they hit the master cylinder. But I ran the stock stamped ones with a little reshaping of a baffle inside. I loved those heads.
 

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
I have the twisted wedge 170cc on a 347. It dynos at 399hp and 425 ftlbs of torque with a wieand stealth intake and a holly 670 street aveneger.

The heads were on a 306 initally that was machined poorly and had the piston skirts touching inside the cyl.

I i stroked it. They are a little small for a 347 but end up making good torque.
 

fishinman78

Contributor
Sr. Member
Joined
Apr 28, 2017
Messages
534
I have the twisted wedge 170cc on a 347. It dynos at 399hp and 425 ftlbs of torque with a wieand stealth intake and a holly 670 street aveneger.

The heads were on a 306 initally that was machined poorly and had the piston skirts touching inside the cyl.

I i stroked it. They are a little small for a 347 but end up making good torque.

Not trying to hijack, but what cam are you running to get those numbers?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
The exhaust ports are in the stock location, so no wider.
Intake ports are all stock as well, so the induction side is no different than stock heads.
As I mentioned earlier, the valve cover rails may be a little higher. I would ask trickflow themselves.
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
The exhaust ports are in the stock location, so no wider.
Intake ports are all stock as well, so the induction side is no different than stock heads.
As I mentioned earlier, the valve cover rails may be a little higher. I would ask trickflow themselves.

valve cover rails are 3/8" taller on mine. taller valve covers for roller rockers as well. tight but doable on drivers side firewall.
 
OP
OP
74 Bronco Billy

74 Bronco Billy

Contributor
Sr. Member
Joined
Jul 4, 2016
Messages
798
I have the twisted wedge 170cc on a 347. It dynos at 399hp and 425 ftlbs of torque with a wieand stealth intake and a holly 670 street aveneger.

The heads were on a 306 initally that was machined poorly and had the piston skirts touching inside the cyl.

I i stroked it. They are a little small for a 347 but end up making good torque.

Not trying to hijack, but what cam are you running to get those numbers?

I gotta know what cam that was x2 Time to fess up Monster Billy

valve cover rails are 3/8" taller on mine. taller valve covers for roller rockers as well. tight but doable on drivers side firewall.

Sounds like my 1" BL will take care of all the size concerns ;D
 

latrucker

Contributor
Sr. Member
Joined
Jul 19, 2010
Messages
647
They are taller. I had trouble finding a set of valve covers that didnt interfere with my c4 shifter linkage. It won't affect intake height. This is on a 351w.
 

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
that 399hp number is on an engine dyno. A chassis dyno would be about 80% of that or roughly 319rwhp

Yes, you are correct. It was in an engine dyno. Sorry i should have been more specific.
It was machined and assembled by basko engines in mesa az
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
I have trick flow twisted wedges on my 347. TEA prepped Twisted Wedge 170 Cylinder Heads 61cc. They fit fine and don't interfere with anything although I run taller valve covers because of my rockers. I run a slightly different cam and intake. The cam is based on the 347, TEA prepped TF heads, 4:11, 33s, 4500 lbs. It's similar to a Comp Cam XE256H but the duration isn't as long. I asked for the torque to come in low and while the intake is an Airgap RPM with a 1500-6500 RPM range, with the heads and cam it will actually shift it down about 500 RPM. I'm roughly 400 HP and 425 ft/lbs of Torque at the crank with the Torque coming on almost instantly. The 303 Cam shifts everything up the RPM range. It's designed for a higher revving motor.
 

Attachments

  • Cam.jpg
    Cam.jpg
    53.1 KB · Views: 123

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
I only know 2 guys that documented flywheel HP on a dyno and upon engine installation they ran a chassis dyno...

You lose a whole LOT more than 20% HP when comparing flywheel and chassis numbers on a Bronco.

Over 30% loss... is what they had.

Sooo many variables but our old skool Broncos lose a lot of power trying to transfer energy through old school tranny's, transfer cases, rear ends, mech fans, 140amp alt, much higher viscosity oils, huge tires....lot of factors...
 
Last edited:

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
So I wanted to back this up because ...Imsure there's a few naysayers on this engine compared to dyno-chassis HP losses- so I looked up a HR magazine test on two dyno'd engines that were later dyno'd in a car...staggering losses... on these cars they difference was averaging 36% loss...

https://www.hotrod.com/articles/ccrp-0311-drivetrain-power-loss/
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
So I wanted to back this up because ...Imsure there's a few naysayers on this engine compared to dyno-chassis HP losses- so I looked up a HR magazine test on two dyno'd engines that were later dyno'd in a car...staggering losses... on these cars they difference was averaging 36% loss...

https://www.hotrod.com/articles/ccrp-0311-drivetrain-power-loss/


Not sure why people are so hung up on HP in these Broncos. Torque i what matters, and yes the Torque loss is still big, it's not as large as with HP.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
Not sure why people are so hung up on HP in these Broncos. Torque i what matters, and yes the Torque loss is still big, it's not as large as with HP.

If torque was all that mattered every single vehicle would have a low reving high torque engine with a small bore and really long stroke and the world would be a boring place hahaha
YOU may only care about torque bit some care about getting through sticky mud, up a steep long sand dune or just smashing the gas getting one the freeway and not having to justify to the passenger being that's less than impressed and convince him that it's all about torque.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
I've got torque up the ying-yang and I feel I'm way short on HP spinning 40"s at 5800rpm...like 68 Ford said, sand and in my case super heavy, wet spring snow wheeling literally sucks every once of HP out of your rig... I'm not interested in tires turning at 10mph at 5000+rpm. To get up a soft sand dune or attack snow at WOT in snow at your headlights... I try to keep tire speed above 45mph...hard to do w/o HP above 5000 rpm.

It's just different wheeling...I love rocks too so just shift the trans and both gearboxes into low and idle...
 
Last edited:

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
74BroncoBilly- I run Trick Flow 205 CNC heads but nothing is stock so I cant help you on clearances to valve covers, the firewall, mc, nothing..
:)

...but I can confirm one thing...just saying you're going to like those heads!!! :)
 
Top