• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

78 full width axle question

MrT

Full Member
Joined
Dec 31, 2019
Messages
288
I have been reading a lot about this swap. I bought axles and I am waitng on them to be shipped.
I kniw about Duff's coil buckets but I have read a few different people drilled out the bottom mounted to offset it. Anybody done it in here? Problems? I was wondering about using Duff's heavy duty lower mounts and redrilling them. Thoughts?
 

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
The full width axle is 6" wider than the EB 44 (3" per side)

It's a little hard to see, but this is my driver's side spring bucket, looking at it from the rear. I cut the bucket loose from the frame and added a 2" boxed spacer and a gusset. Also shown is the bracket for the F250 shock mount

31436498097_b2201c627c_o.jpg



I drilled the lower coil mount offset 1" to make up the difference
46375779601_af66a89765_o.jpg



I would not want to drill the lower mounts any further than 1" from their original holes. Even if you could fit a 3" offset in the lower mounts, you would likely bend them under load.
 
OP
OP
M

MrT

Full Member
Joined
Dec 31, 2019
Messages
288
I knew the axle is 6" wider but I thought the coil mounts were only 2" off per side? I believe the Duff buckets are 2" offset.
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
The full width axle is 6" wider than the EB 44 (3" per side)


This is incorrect. A '78 front axle is 6" wider than an EB axle, but the 6" is all in the passenger side. If you narrow a full size axle to be EB length, you cut 6" from the passenger side and leave the driver side alone.
 

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
This is incorrect. A '78 front axle is 6" wider than an EB axle, but the 6" is all in the passenger side. If you narrow a full size axle to be EB length, you cut 6" from the passenger side and leave the driver side alone.

Yes, you are correct. I was only speaking in terms of spring position relative to the frame.
 

RT

Bronco Guru
Joined
Sep 29, 2003
Messages
1,037
I just offset the lower mounts 1" over, stuck the springs in and the top almost fell into the stock upper mount. Been running it this way daily driven and wheeled for around 9 years now and still wondering if I should do anything with the uppers. :) Confuses the heck out of spotters though as the shocks are straight but the coils are angled, looks like something's bent,,,,, aside from the driver,,,
 

R0kcrwlr

Full Member
Joined
Oct 10, 2001
Messages
189
I just got my 78 axles last night so I will be researching the same issues so I will provide updates on my progress.
 

R0kcrwlr

Full Member
Joined
Oct 10, 2001
Messages
189
What are some options to mounting the trac bar to the axle when going TRO on a full width axle?
 

78Scronco

Bronco Guru
Joined
Nov 2, 2005
Messages
1,282
when I did my full swap, I turned the stock cups around and re drilled., but I didnt like the spring leaning to the inside. I installed the Duffs HD cups and offset coil buckets. much better.
 

78Scronco

Bronco Guru
Joined
Nov 2, 2005
Messages
1,282
the other issue I ran into(and still have this problem) is the front driveshaft not have a clear straight angle to the transfer case. I'm using ZF and NP205, so thats a little different, but I didnt see anyone mention that problem before I did it. The exhaust is in the way due.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
the other issue I ran into(and still have this problem) is the front driveshaft not have a clear straight angle to the transfer case. I'm using ZF and NP205, so thats a little different, but I didnt see anyone mention that problem before I did it. The exhaust is in the way due.

As long as you run a double Cardon joint at the t case the angle doesn't matter. Mines at quite an angle as far as side to side goes and I drive at very high speeds in 4wd, no vibrations.
 
Top