• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New owner from Germany

OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
further emptied the dash area today:
IMG_3510.jpeg

IMG_3513.jpeg


nothing serious, rust-wise. but i'll clean it all up and repaint it.

lots of side-projects:
IMG_3512.jpeg


and a big question - go for the preformed firewall insulation or fab up something on my own?
IMG_3515.jpeg


and on my passenger side folding seat - what's missing here? a rubber bumper?
IMG_3514.jpeg
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
as far as firewall insulations go - is there more than one option?
i found the quietride catalog, listing two versions of the insulation, and cjponyparts specifically sells their product.
more expensive than tom's and the other places, but they do not mention who the manufacturer is...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I know the pre-molded ones like we sell are good at their job. But I don't think it's necessarily the only good option. Lots of insulating products out there, and maybe some in your country that we don't know about here.
The nice thing about the pre-molded ones is that you don't have to cut and form and cut and shape and cut and cut something to make it work around all the angles. But if you do it yourself you might be able to use comparable, or even better insulating products and leave a little more room under the dash.

One of the best for that might be the spray-on stuff like Lizard Skin where you spray on the sound deadener first, then a layer of thermal barrier coating and get good protection from both.
Whatever you do though, do it up the best you can because the transmission tunnel, front floor, and especially the firewall and cowl areas are where most of the heat comes into the cabin. And a lot more noise than most people realize.

Paul
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
One of the best for that might be the spray-on stuff like Lizard Skin where you spray on the sound deadener first, then a layer of thermal barrier coating and get good protection from both.
Whatever you do though, do it up the best you can because the transmission tunnel, front floor, and especially the firewall and cowl areas are where most of the heat comes into the cabin. And a lot more noise than most people realize.

definitely won't hurt...
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
Merry Christmas everyone!
A quick update before the year is over. Bought the Firewall insulation from CJPony, it's a complete set from QuietRide. Firewall insulation, cowl insulation, a set of fasteners. We'll see how well it fits.

I also cleaned up the firewall a little and started welding some holes closed:
IMG_3526.jpeg

IMG_3527.jpeg


More to come in the new year!
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
I found come rust! Nothing major, but underneath the driver side air vent were some holes:

IMG_3581.jpeg


That seemed impossible to weld, and I did not want to cut out a piece of the sheet metal, so out with the lead:

IMG_3582.jpeg


Let's see if that holds up!
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
I have a small copper plumbing coupler that I have flattened for uses like that. Hold it up under the weld and start tacking. The wire won't weld to the copper and the copper dissipates the heat from the weld. Your option worked too.
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
applied seam sealer on the inside:

IMG_3596.jpeg


turned out that was a little too quick.
removed the passenger side fender and cut a large portion of the fender apron out. when welding it back together it'll surely burn through to the inside %)

IMG_3597.jpeg


what's the consensus on fixing this area? just weld in one piece? or make two overlapping panels as it was before?

the driver side is just as bad. it just has a patch panel put over the rust hole :(
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
I think it would be easier to fab a couple panels for that area rather than cutting the whole piece out. You are doing a nice job on those repairs.
 

mp

Bronco Guru
Joined
Dec 22, 2001
Messages
2,921
Loc.
Austin, TX
Nice progress! Looks like I am probably coming back for Oktoberfest 2020, so let me know if you need anything that will fit in a big suitcase!
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
Already hooked on the Oktoberfest? :D
You're always welcome over here!
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
decided to put in just one piece instead of two overlapping panels.

made me a template and test fitted a new piece:
IMG_3600.jpeg


clears the air duct just fine:
IMG_3599.jpeg


made some holes, filed one square:
IMG_3601.jpeg


now i just need to weld it in...
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
this is somehow going downhill very quick...
no welding today, more disassembly.

on the passenger side, i cleaned up some areas that looked suspicious.

IMG_3605.jpeg


notice the lower left corner? yup, that's where the patched in floorpan is.

IMG_3606.jpeg


nice view from the inside. considering cutting them out and welding them in properly, not badly overlapping as they are now.

IMG_3607.jpeg


the other side is giving me nightmares already. notice the rivets:
IMG_3608.jpeg


kick panel not attached to the wheelhousing, and another pice riveted in instead:
IMG_3610.jpeg


couldn't get the fender off completely. after stripped bolts, broken j-nuts, torn openings in the fender and a quick use off the sawzall, i finally struggled to get the three rear bolts off. soaked them, and will try to hit them with an impact next weekend. need to get some decent bits in the right size first!
IMG_3611.jpeg


the front corner on the driver side where the radiator support meets the fender looks badly welded, too. i might have a lot more welding to do %)
 

74BroncoCO

Bronco Guru
Joined
Nov 3, 2004
Messages
2,378
It rainy and dreary in Germany this time of year...so it's a good time for this sort of thing. You'll get it knocked out quicker than a lot of folks do.
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
indeed, it's raining, but fairly warm. ideal garage weather...
the driver side fender is off. of course two of the three bolts in the a pillar snapped right off. let's see if i can drill them out and recut the inserts. if all else fails, helicoil inserts.

here's what I cut out on the driver side:
IMG_3630.jpeg


4 layers in this area, that was definitely an amateur repair.
there was one badly rusted layer between kick panel and firewall - i have no idea whether or not this was factory. but it was so badly rusted i cut some spot welds:
IMG_3632.jpeg


the wheel housing lip is pretty thin and rusted through in some places:
IMG_3631.jpeg


but i will definitely need a new fender apron. this is what the front corner looks like - i already suspected this, see above.
IMG_3633.jpeg
 
Top