• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Quality radiator

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
I just got the rebuilt 302 engine and trans. back in. Two years. I could use advice in locating a QUALITY radiator. Preferable with the built in trans. cooler tank. Street driving with occasionally dirt roads. Quality is more important than price. Thanks
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I ruined my radiator a couple years ago, and needed a quick replacement. Since I live in the Northwest, I use Toms a lot. I can usually get my stuff the next day if I order in the morning.
I bought their aluminum three core radiator. This is the first time I've put an aluminum radiator on an old car, so I was a bit apprehensive.
This is a really nice reproduction of the original. Fit perfectly in every way.

As far as the performance goes, it has kept the temperature right on the 190 mark with the A/C on whether idling in traffic or pulling grades on the freeway.

This is a really nice piece.
https://www.tomsbroncoparts.com/pro...es-auto-or-manual-66-77-early-ford-bronco-new
 

BoltTurner

New Member
Joined
Aug 18, 2012
Messages
33
when you switch to aluminum, do you need to swap the heater core to aluminum as well? Or does the anode take care of the electrolysis issues?
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
I've been recommending the bc 3-cores for years but it looks like they no longer carry em. Someone posted driven auto parts sells the same ones.
 

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
You can still get them from BC Broncos you just have to call them. These are top quality radiators.
 

AC932

Full Member
Joined
Sep 17, 2018
Messages
254
I'm very happy with the Toms copper OE style. It did overheat once, on the ascent over the mountain into death valley, but has otherwise run at whatever the thermostat is.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
when you switch to aluminum, do you need to swap the heater core to aluminum as well? Or does the anode take care of the electrolysis issues?

That's a good point.
No, I'm using a Vintage Air unit. I don't see an aluminum heater core as an option.
I'll check the anode to see how it's holding up.
 

NashBronco

Contributor
Sr. Member
Joined
May 9, 2013
Messages
398
Loc.
Flowood, MS
I bought the BC Triple Pass radiator about a year ago. It wasn't cheap but looks more stock and cools very well. Very pleased with it. not sure if they offer one with the tans cooler built in.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I bought the BC Triple Pass radiator about a year ago. It wasn't cheap but looks more stock and cools very well. Very pleased with it. not sure if they offer one with the tans cooler built in.

By design they kind of can't offer the tranny cooler in the triple pass radiator.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
I've had their standard 3-core in both broncos for years. Keep the 351s cool in la traffic no problem. I'm about to do an auto swap on the 72. Dont know whether to run an external cooler or upgrade the radiator to one with it.
 
OP
OP
J

johnbeck

Sr. Member
Joined
Aug 11, 2015
Messages
534
For simplicity sake I'd prefer the built in trans cooler. I've heard the water cooling drops the trans. temp better than the air cooling. I live near the coast so over heating is a major problem. I'm mostly looking for a sturdy build with quality fittings in the stock configuration.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
For simplicity sake I'd prefer the built in trans cooler. I've heard the water cooling drops the trans. temp better than the air cooling. I live near the coast so over heating is a major problem. I'm mostly looking for a sturdy build with quality fittings in the stock configuration.


The bc or driven auto parts is probably the way to go but I couldn't find the information on bc's website to see what they offer. I didnt check driven ap yet.
 

luke

Sr. Member
Joined
Sep 19, 2010
Messages
370
Autozone copper 3 core factory replacement v8 radiator. Surprisingly nice, built in trans cooler just like factory. Comes painted black. Made in Mexico. Very nice. $200.
 

NewDog

Contributor
Full Member
Joined
Oct 30, 2018
Messages
221
Loc.
Surrey BC
Has anyone run the radiator cap with the sacrificial magnesium anode from WH? and ifso which one 13lb or 16lb? I'm running a 302 that came with the bronco I'm assuming original. https://www.wildhorses4x4.com/product/Rad_Cap_EME_14lbs/Bronco_Aluminum_Radiators or https://www.wildhorses4x4.com/produ...e-16lb-Radiator-Cap/Bronco_Aluminum_Radiators

I'm not sure about the sacrificial anode cap, but there is a good discussion and a good article (thanks langester) about rad cap pressure ratings in this thread:

https://classicbroncos.com/forums/showthread.php?t=302844
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
For simplicity sake I'd prefer the built in trans cooler. I've heard the water cooling drops the trans. temp better than the air cooling. I live near the coast so over heating is a major problem. I'm mostly looking for a sturdy build with quality fittings in the stock configuration.

Living near the coast I wonder if the aluminum radiators corrode even faster than they already do under standard use.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
when you switch to aluminum, do you need to swap the heater core to aluminum as well? Or does the anode take care of the electrolysis issues?

No you don't. But it's not a bad idea either.
Adding more aluminum is still using dissimilar metals because in our case the engine block is still cast-iron. But when you eliminate one copper/brass component in favor of aluminum, and maybe even another pair if you swap to aluminum heads, the only one left is the heater core. So making that aluminum too is not a bad way to go.
Instead of three different metals you only have two then.

I've heard the water cooling drops the trans. temp better than the air cooling.

Not sure that's a complete statement.
The ultimate capacity of a water cooled setup is potentially higher than an air cooled unit, with the GVWR ratings usually higher for a given size. But therein lies some of the issue. Just how big can you make the cooler coil and still fit it inside a given radiator tank? Especially a Bronco radiator tank!

And oddly enough, when the factories use both (as they often do on pickup trucks) the air cooling unit is plumbed in line first, before the water cooled unit.
This allows the air cooler to do it's job (sometimes too well if the weather is not hot) and allows the liquid cooler to actually bring the heat back up to an optimal level for the trans to work properly!

I guess I'm saying that you can't just lump all the theories together in the real world and have them act the same way in every circumstance. Sometimes you get more bang for your buck with an external air setup.

Has anyone run the radiator cap with the sacrificial magnesium anode from WH? and ifso which one 13lb or 16lb?

Lots of people. Been around the hot-rod world for almost 30 years now I think.
Sacrificial anodes in the cap like that, or in the drain plugs are available in some cases. In my opinion, when it comes to aluminum in old vehicles, anything helps!

I'd say 13lbs unless you have an overheating issue. The higher the pressure rating, the better from a boiling standpoint, and from the standpoint of keeping higher pressures inside the system helps to keep coolant in the tight pockets of the water jacket. But it's all about what the individual components are comfortable with. Likely your system can handle the 16lbs no problem, but if you know it's prone to leaking in various areas at hose junctions, solder joints and gaskets, a 13pounder is likely safer. I think stock was either 13 or 14, so that's the most common we sell I believe. Have not looked at the numbers, but I'd bet that's the case.
Most modern vehicles with aluminum radiators run higher pressures too if I'm not mistaken, but it's not just because they're aluminum. Everything is set up to work that way.

Living near the coast I wonder if the aluminum radiators corrode even faster than they already do under standard use.

Very likely. Not sure it's an issue with the factory ones with plastic side tanks, and I can't say from first-hand knowledge that it happens quicker with all-aluminum ones. Just that it seems likely. Along with everything else that corrodes at the coast.

When it comes down to it, aluminum is more sensitive to the whole electrolysis/galvanic reaction thing, than are copper or brass. So it behooves EVERYONE that converts to an aluminum component in the cooling system (heads, radiator, heater core, intake manifold, etc.) to make sure that their electrical system is 110% in good shape and working properly. In other words, bring it at least into the nineties instead of leaving it in the fifties.
Grounds, grounds, and more grounds.

Oh, and instead of being lazy about it like many of us were (including me especially) change your engine coolant religiously according to either the manufacturer's recommendations, or the frequency required as indicated by testing.

As far as grounding the radiator as part of your electrical system, I'm still on the fence. Some great minds say to do it, but others say not to. And I lean into that camp, with instead of grounding it, keeping it as isolated from the rest of the system as possible. In my opinion, you want your coolant acting as little like an electrode as possible.
But it'd be neat to see some real world testing done with sacrificial anodes installed in radiators that are grounded and those that are not.
For now though, I look to the OE's and I've yet to personally see a factory installation that was grounded to the chassis. Aluminum or copper.

Paul
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
My Bronco has always had an aluminum timing cover and a brass radiator. I never considered it an issue.
So now I retract my "good point" comment about having a brass radiator core after putting in an aluminum radiator.
Sometimes it takes me a while to come around.%)
 
Top