• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Door hinge backing plate removal

kat

Bronco Guru
Joined
Jul 22, 2015
Messages
1,057
Loc.
Bristol
I have searched in here and can't come up with the best way to attack this. 1976 drivers side door needs hinge backing plate replacement, there is no saving the original plates. So got two new ones coming soon. I have read two different ways to go about this.

1-Take front fender off and cut doors into the back side.

2-Cut doors into the kick panel inside cab.

I do have fiberglass kick panels/speaker pods already in place so if I cut a hole on the inside Im assuming this will cover it up. Seems easier than taking fender off.
Can anyone show me some good pics of what they did and where to cut? Either option 1 or option 2. Just need some guidance. Please keep in mind that my Bronco is not pristine and not plan on being perfect. Thanks
 

DonH

Contributor
Sr. Member
Joined
Mar 8, 2013
Messages
487
Loc.
WA State 30 miles from the beach
I posed pictures a couple weeks ago of what I did.
A few years ago I was able to take the fenders off a 68 I restored. I opened the back side of the post, made new plates and welded them back. Now my 67 that I am restoring is so rust locked if I were to remove te bolts they would twist off and creating other problems.
Going from the inside does not look much better.
I opened from the door side, removed the plate re-drilled it, put it back in and welded it back up.
Like you said, my Bronco is not a show rig, it is for me and I am restoring to get it back on the road for ME.
 
OP
OP
kat

kat

Bronco Guru
Joined
Jul 22, 2015
Messages
1,057
Loc.
Bristol
I posed pictures a couple weeks ago of what I did.
A few years ago I was able to take the fenders off a 68 I restored. I opened the back side of the post, made new plates and welded them back. Now my 67 that I am restoring is so rust locked if I were to remove te bolts they would twist off and creating other problems.
Going from the inside does not look much better.
I opened from the door side, removed the plate re-drilled it, put it back in and welded it back up.
Like you said, my Bronco is not a show rig, it is for me and I am restoring to get it back on the road for ME.

Im trying to picture in my head where to cut. Does the plates slide out towards the outside of door jam?
 

Yooper74

Full Member
Joined
Aug 13, 2020
Messages
322
I took fender off and cut back of A-pillar. Cut 3 sides of a ‘box’ and bent it open like a can. Was fairly easy to find where backing plate is. I think I have a picture of it I can look tomorrow and post it.
 
OP
OP
kat

kat

Bronco Guru
Joined
Jul 22, 2015
Messages
1,057
Loc.
Bristol
I took fender off and cut back of A-pillar. Cut 3 sides of a ‘box’ and bent it open like a can. Was fairly easy to find where backing plate is. I think I have a picture of it I can look tomorrow and post it.

Thank You
 

DonH

Contributor
Sr. Member
Joined
Mar 8, 2013
Messages
487
Loc.
WA State 30 miles from the beach
Im trying to picture in my head where to cut. Does the plates slide out towards the outside of door jam?

This is where I cut.
 

Attachments

  • H 1.jpg
    H 1.jpg
    97.5 KB · Views: 167
  • H 2.jpg
    H 2.jpg
    88 KB · Views: 154
  • H 3 (2).jpg
    H 3 (2).jpg
    86.1 KB · Views: 144
  • H 6.jpg
    H 6.jpg
    141.6 KB · Views: 142
  • H 10.jpg
    H 10.jpg
    117.5 KB · Views: 178

Yooper74

Full Member
Joined
Aug 13, 2020
Messages
322
Here's what I did. Was relatively easy to determine where to make the cuts

I used a dremel tool with a small metal cutoff wheel

door hinge plates.jpg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I remember the first time I actually noticed the recommendation in the Chilton's manual to put sealer under the top edge of the hinges when you were putting a door back on the vehicle. We were always removing the top and doors for the summer, but never actually bothered to look at the book on how to do it. Was surprised there was even a "best practice" mentioned for something so simple.
I had wondered at the time why I'd never noticed it before though, because I basically read the book cover to cover when I first got it, and by that time I was already dealing with rust issues.

Luckily my door bolts were still workable (I wonder if they still are today?) but were already showing signs of the dreaded rust. In less than five years of life my 71's kick panels had already rusted through and had patch panels screwed to them by the PO.

Needless to say, as soon as I saw that I went out and ran a bead of silicone sealer around the perimeter of the upper and lower hinge plates from the outside. Not the best method, but looked like a nice "weld" around the edge and I figured it would at least give what metal was left a fighting chance at survival.

I did that on quite a few spots on the Bronco's body that were never quite sealed from the factory. Don't know if they stopped the rust, but at least most of them stopped the water from getting into the cabin that I could see.

Good luck getting your plates out. Hope I don't have to deal with it, but someday I'm probably still going to have to replace the entire post and panel from the early rust-through.

Paul
 
OP
OP
kat

kat

Bronco Guru
Joined
Jul 22, 2015
Messages
1,057
Loc.
Bristol
Here's what I did. Was relatively easy to determine where to make the cuts

I used a dremel tool with a small metal cutoff wheel

View attachment 526204

Thank you for the pics. I think I will go this route with a dremel tool. Unfortanatly won't be able to weld them back up. Instead Ill use some fiberglass or something.

This pic has me confused with the bed of the Bronco in the background. Is this the passenger side looking under fender?
 

jperry1290

Sr. Member
Joined
Jul 1, 2010
Messages
920
Just for thought. I did this around 10-12yrs ago when I first bought my EB. I cut from the inner fender side. Last year I replaced one of the door posts and inner kick panel due to rust. I wish I had done that 10-12yrs ago when the parts were cheaper and I had more free time. Overall it wasn’t to difficult if a job.
 
Top