• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Confirming TB drop bracket

Shimmy

Contributor
1977 Bronco
Joined
Jun 20, 2021
Messages
1,396
Loc.
Maple Valley
Sorry to create a thread on this but in my hours of searching the WWW, I couldn’t find a pic of the stock track bar bracket. I’m running a 3” pitman arm drop and it just about lines up with my track bar bracket. And from what I’ve gathered my bronco has an older Duff kit.

Just making sure I’m thinking of this correctly… can y’all confirm this is a dropped track bar bracket?
 

Attachments

  • B2B64F79-2AE9-43C9-97BC-56C8341B0691.jpg
    B2B64F79-2AE9-43C9-97BC-56C8341B0691.jpg
    71.1 KB · Views: 150

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
No, it's not. It looks like a stock '76 or '77 Bronco trackbar bracket.
A drop bracket on 99% of Broncos is going to be an additional piece bolted and/or welded to the original one. There are some that replace the original completely, so those would be a single bracket welded to the frame like yours is, but since you have a '77 and that looks like an original, I'm sticking with that assesment for now.

Looks like you do have a dropped pitman arm, so if you do not have a trackbar riser (raises the lower bracket up above the axle) then you do need a trackbar drop bracket to match the pitman arm.
You only rarely do one or the other. In most cases you must do both so that the angles match the factory angles.

Paul
 
OP
OP
Shimmy

Shimmy

Contributor
1977 Bronco
Joined
Jun 20, 2021
Messages
1,396
Loc.
Maple Valley
Looks like you do have a dropped pitman arm, so if you do not have a trackbar riser (raises the lower bracket up above the axle) then you do need a trackbar drop bracket to match the pitman arm.
You only rarely do one or the other. In most cases you must do both so that the angles match the factory angles.

Paul

I think thats where i'm confused. The drop pitman aligns with the TB bracket so my draglink is parallel with the TB. That led to to believe i had some kind of aftermarket bracket.?:?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I guess we need to find a shot of a stock "Inverted-Y" setup to see just how the two bars line up with each other. Most of what you read here about them being "parallel" revolves around the earlier "Inverted-T" style linkage. The later linkage was different in design completely, but there may still be something to that parallelism.

I don't remember the exact angles, but matching factory angles involves changing none or both. Can't change just one (adding a pitman arm for example) and have them still the same as original.
Maybe they had some trouble with the linkage and did their best to correct it.
Is it lifted also?

Can you post up a shot of the whole setup, side to side? Including a closer shot of the lower end of the trackbar?

Thanks

paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Could it be the angle of the photo that it looks like a dropped pitman arm, but is not? Sure looks like one to me though.
I forgot to point out too that the pitman arm appears to be one of the '78/'79 full-size arms instead of the typical EB arm. Might be someone's special design for Broncos, but it looks more like our full-size arm (https://www.wildhorses4x4.com/product/Drop_Pitman_Arm_7879yr/fullsize-bronco-tierods-draglinks) which has less drop than an EB-specific arm.
These are often used on '76 and '77 Broncos when changing over to the older Inverted-T setup. I wonder if there was a linkage swap done earlier on the Bronco and then someone changed back to the later style without changing the pitman arm too?

How long have you had the Bronco, and what all have you done to it already? Any changes to the steering linkage and suspension while you've had it?

Paul
 
OP
OP
Shimmy

Shimmy

Contributor
1977 Bronco
Joined
Jun 20, 2021
Messages
1,396
Loc.
Maple Valley
I've had the bronco for about a month now. From spending hours under the chassis, i'm starting to realize that parts of this suspension were pieced together... some Duff, some custom fabbed, some i'm like "what happened here?" hahah. I'm working on replacing the entire suspension with a 3.5" which is what appears to be on it now.

I've attached some pics below. The y setup is parallel with the stock TB. It appears to have a 3" drop pitman arm? The TB mount is stock on the axle side and I was questioning the frame mount since it lines up with the drop pitman arm.

I'll be swapping to the WH T setup and adjustable track bar (sitting in my garage), but as the truck sits i have absolutely no bumpsteer or death wobble. I just hate these Y setups. haha! Thanks for all your insight Paul!
 

Attachments

  • IMG_1368.jpg
    IMG_1368.jpg
    105.4 KB · Views: 96
  • IMG_1370.jpg
    IMG_1370.jpg
    96.1 KB · Views: 78
  • IMG_1371.jpg
    IMG_1371.jpg
    63.9 KB · Views: 66
  • IMG_1373(1).jpg
    IMG_1373(1).jpg
    86.7 KB · Views: 80
Last edited:
OP
OP
Shimmy

Shimmy

Contributor
1977 Bronco
Joined
Jun 20, 2021
Messages
1,396
Loc.
Maple Valley
and another showing the steering angles. my understanding is that y setups still need to be somewhat parallel (on the same plane). I had issues on my previous jeeps when they weren't.

given my current setup, i think i TB riser on the axle side would cause the TB/DL to be out of plane.
 

Attachments

  • IMG_1367.jpg
    IMG_1367.jpg
    83.9 KB · Views: 80
Last edited:

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Here's a front pic of a 77 Bronco. This is a stock bronco no lift.
 

Attachments

  • 70969743_566932151545698_Orig.jpg
    70969743_566932151545698_Orig.jpg
    113.9 KB · Views: 80

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
The y setup is parallel with the stock TB. It appears to have a 3" drop pitman arm?

But parallel is slightly different from a T style. Note savage's setup with no modification. The "draglink" on the Y setup is much longer than the original, where the normal parameters apply. Which are length, plane and parallel. In the case of the Y the lengths are all different.
Apples to oranges...

The TB mount is stock on the axle side and I was questioning the frame mount since it lines up with the drop pitman arm.

But it doesn't actually. It lines up nicely to our eyes, but it's still off from original.

I'm working on replacing the entire suspension with a 3.5" which is what appears to be on it now.
I'll be swapping to the WH T setup and adjustable track bar (sitting in my garage), but as the truck sits i have absolutely no bumpsteer or death wobble.

So don't do anything else to this setup, as you are going to be changing to the T setup at some point. Since it's not giving you any bump-steer trouble, don't sweat it. It would never cause a Death Wobble anyway. That's from other things.
Keep the existing dropped pitman arm, keep the stock upper trackbar bracket (do NOT use a drop bracket when you put the T system on) and see how it all works together at that point.

You will likely need a tapered shim to go into that pitman arm. It probably has one now, but you should double check when you get it apart and if you do have one, don't toss it out.

I just hate these Y setups. haha!

How come? Well, they do have their weaknesses, and they usually come out when you lift the vehicle and run larger tires. So if that's the case, then they're not the best choice. But when left stock the Broncos (and F150's) that used the Y setup had VERY good street manners for the most part.
Larger tires alone can mess that up, especially off road. But add a lift too and some things go south pretty quickly.

Paul
 
Top