• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

77 Help

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
So you may have seen my post where I just picked up a 77. So I got a question. It's an automatic 302 and I hope I can explain what it is doing so that you guys can understand but when I put it in drive it feels like the rear end shifts a little bit and it also does it when you pull away from a stop sign. Has anyone had this issue or does that make any sense. I have not got under it to see if I can see what is going on but I thought I would start with you guys and see if you had any suggestions.

Thanks
Brent
 

fordfan

Bronco Guru
Joined
Sep 13, 2009
Messages
3,592
What you are describing is infamous "Bronco Clunk" in which the rear axle twist in the U bolts. The springs can also have a little bit of 'spring wrap' that multiplies what you feel.
Tighten your U bolts or replace them with new ones and it should get better.
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
Awesome. I plan on replacing the springs in the rear anyway so I guess maybe the complete kit will take care of that. My vin says that my bronco came with HD springs. Does anyone sell those to replace the stock ones?
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
ck-in w/any of the "typical vendors" or find those parts for less at most big box stores (autozone, etc). I like oe & i's' Y I come here, the bronk buddies tell me Y/M/M to swap in.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Parts replacement is the worst diagnostic technique known. A differential shop that sees this kind of thing daily would likely know quickly if the axle is turning. Another consideration is a dry slip joint in the drive shaft. They bind and release making a bang noise.
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
I checked it out today and the rear axle is flexing back and forth when put in drive or reverse. I am going to grease the drive shaft to see if that helps. Not sure what to do about the rear rolling!
 

Kbpony

Sr. Member
Joined
Jan 31, 2012
Messages
386
If the tube is slipping in the u-bolts, you should be able to see witness marks. If so, replace u-bolts ASAP. U-bolts are designed to be one-time use. Once tightened to spec, they have been stretched and should not be re-used. If your axle is wrapping (my '77 was) you will need to go to a heavier spring pack or an anti-wrap device.
 

JeffG

Contributor
Sr. Member
Joined
May 7, 2004
Messages
513
Loc.
San Antonio, TX
Agree with everyone else, and since you are planning on new springs and new u-bolts that should take care of it. Also, since this is a new to you Bronco check all the suspension and drivetrain for dry/rotted bushings and driveshafts for bad u-joints.

I recall a few have had they leaf spring hanger bolts to loosen up. It can cause the mounting holes to get an "egg shape" and could cause some movement. Just look over everything when you swap your new springs in.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Some things that go bump in the night (and any other time) on an Early Bronco are:
As mentioned...
1. Springs not tight on the perches and wear having rounded them off.
2. Sticking driveshaft slip joint.
3. Worn out spring bushings (though not a common source of what you're describing, they still add to it).
4. The spring mounting bolt holes in the spring hangers on the frame having wallowed out into oval shapes.
5. The serrated ends of the original bushing sleeves having worn into the inside edges of the spring hangers.
6. Leaf spring center pins broken.
7. Leaf spring clamps loose or broken, individual leaves fanned out, separated, broken or sagged unevenly with the others in the pack. Generally just the norm for an old tired and worn out spring pack.

8. Or all of the above!

You won't usually get rid of the slip-joint stiction in the driveshaft by simply greasing the Zerk fitting. If you're lucky it will help, but if not you will need to separate the two halves, clean the splines and grease them manually before putting it all back together.
That will usually get rid of the clunk for a few months, but it usually comes back. Timing depends on how much you drive it.

Some of the Bronco vendors used to sell factory style replacement leaf packs. We don't, but some might still.

Paul
 

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
When the axle starts rocking on the springs, you can usually see wear on the spring perches. Might be a good idea to replace those with longer perches to prevent it from happening again. But you have to be careful not to bend the axle housing when welding on it. When you get it hot in one spot (i.e., welding) it WILL bend.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
the automatic Bronco can get a pronounced klunk going into gear with a bad drive shaft u joint or bad centering ball in the CV coupler. its always worth the time to pull the driveshaft to inspect everything and re grease the unit.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
What you are describing is infamous "Bronco Clunk" in which the rear axle twist in the U bolts. The springs can also have a little bit of 'spring wrap' that multiplies what you feel.
Tighten your U bolts or replace them with new ones and it should get better.

and it never fails right.. :)
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
Went to my car clubs cruise in this evening. On the way home the headlights started blinking on and off. Thoughts?????
 

Slowleak

Bronco Guru
Joined
Sep 12, 2013
Messages
4,013
Loc.
Georgia
Went to my car clubs cruise in this evening. On the way home the headlights started blinking on and off. Thoughts?????


Sounds like the breaker in your headlight switch is getting tripped. It could be a short, bad switch, bad dimmer switch, or if you are running newer bulbs like an H4 it may just be overloading the breaker. If that's the case, you need to add headlight relays.
 

fordfan

Bronco Guru
Joined
Sep 13, 2009
Messages
3,592
Sounds like the breaker in your headlight switch is getting tripped. It could be a short, bad switch, bad dimmer switch, or if you are running newer bulbs like an H4 it may just be overloading the breaker. If that's the case, you need to add headlight relays.

Yes... Exactly what Mark said... People change their old headlights to new high output Halogens and the switch can't handle the current and trips a built-in breaker. Sometimes the new switch won't handle as much current as the old switch either...
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
Please forgive my dumbness but where is the breaker for the headlight switch located?
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
I just bought this bronco so I don't know what light bulbs are in it. And it didn't do it starting out but as We were on our way home it started. But when we got home and parked it in the shop and let it sit for a few minutes and turned them back on it didn't do it
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
It's a common symptom especially in Broncos for some reason. I think it's the less than stellar wiring scheme, or maybe just more wear and tear typically. And I have seen specifically 1977 Broncos with extremely poor condition wiring even compared to older models. So it could be a voltage drop overall wiring putting more load on the switch, or could be halogen lamps putting slightly more load on things. But more likely it's just the switch itself got old.
The circuit breaker is built into the headlight switch. Nothing else to change other than installing a new headlight switch. But you might even forestall that action by installing headlight relays instead. Many times the relays have allowed even an old tired switch to continue to work.

And speaking of continuing to work, if this ever happens again, on any vehicle, go up front and disconnect one headlight. Yes it kind of screws up the driving experience, but not as bad as having both of them flip off! By halving the load on the switch it can often stop the problem temporarily.
 
Top