• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Nearly elect. Fire…

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
Headed to a car show today and my speaker bar shorted out, then I restarted it played fine. Then I caught a whiff of smoke so I pulled over immediately and smoke started bellowing out from under the dash. Shut her down and the smoke quit. When I got it home (towed) I took a quick look and see the wires going to my ignition switch are the ones that burned. This isn't original wiring harness and I haven't changed anything in a couple thousand milesÂ…what can cause a short like this? Is it possible vibration caused two wires to short? Or would it be something in the ignition switch?

I haven't checked the fuses yet.

Thankful I shut her down quick and it didn't get out of controlÂ…
 

Attachments

  • 64AEF4ED-D9C9-42D5-8679-5302EA878859.jpg
    64AEF4ED-D9C9-42D5-8679-5302EA878859.jpg
    86.1 KB · Views: 258

ared77

Contributor
Bronco Guru
Joined
Apr 21, 2013
Messages
3,178
"my speaker bar shorted out"

What exactly did you mean by this? Reason I ask is usually "shorted out" means an electrical short. That means current is flowing (fast) from positive to negative and things like wire insulation start to melt. And smoke!

So if you noticed something odd at the speaker bar, chances are it was the original problem and the wires you found melting were just the weakest link of the circuit that supplies the voltage to it.

Good luck getting it fixed up.

Norm
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
"my speaker bar shorted out"

What exactly did you mean by this?

Norm

The speaker bar is connected to the ignition switch just like a radio, so that when you turn the vehicle off the speakers are off. However the main power source for driving the speakers is direct from the fuse box. The “short” means that the speaker turned off and quit working while the ignition was on and running, and so I pressed the on button on the speaker and it came right back on.

Hypothesis 1: so my thinking is the ignition switch had a brief short which looked like the same scenario as turning off the ignition switch. The “short” at the ignition switch then resulted in fused wires and burnt coating.

Or

Hypothesis 2: some problem in the speaker caused it to draw high amounts of amperage and burned up the ignition switch wires.

How to test either of these independently? After replacing the ignition switch, I'm guessing to use a multimeter on the speaker to ignition line to see if anything weird is happening thereÂ…assuming it still works.
 

knack

Contributor
Sr. Member
Joined
Feb 2, 2007
Messages
877
If you don't have one in there already, a fire extinguisher should go on your gift list for the holidays!
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
The speaker bar is connected to the ignition switch just like a radio, so that when you turn the vehicle off the speakers are off. However the main power source for driving the speakers is direct from the fuse box. The “short” means that the speaker turned off and quit working while the ignition was on and running, and so I pressed the on button on the speaker and it came right back on.

Hypothesis 1: so my thinking is the ignition switch had a brief short which looked like the same scenario as turning off the ignition switch. The “short” at the ignition switch then resulted in fused wires and burnt coating.

Or

Hypothesis 2: some problem in the speaker caused it to draw high amounts of amperage and burned up the ignition switch wires.

How to test either of these independently? After replacing the ignition switch, I'm guessing to use a multimeter on the speaker to ignition line to see if anything weird is happening thereÂ…assuming it still works.

another question once you narrow it down was this a fused circuit and why didn't a fuse just blow??painless seems to have alot a fuses .... insufficient wiring for the circuit amperage rating??

SHORTS can be either a short to power wire,a short to a negative wire or a short to body/frame ...
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...a brief short which looked like the same scenario as turning off the ignition switch.
When the WIRE shorted, it couldn't carry enough current (Amps) to supply the short AND the other loads at battery voltage. So the voltage dropped between the ig.sw. and short (where the wire got hot) leaving LESS voltage for the loads. Some of them might have tolerated the low voltage, but the speaker electronics interpreted the lower voltage as key-off, so it shut down. By the time you pressed the button to turn it back on, the voltage had come back up (for whatever reason) enough for the speaker to turn on again.
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
I had my wiring smoke behind the switch also. I was 6-12 months into a new centech harness. When I called their tech he said the common cause for this was one of the blades not lined up correctly on the rear of the switch. Sure enough that was the culprit. It's real easy when you plug the harness to the rear of the switch to have a blade miss its female connector but still make contact causing heat over time. Centech sent me a new switch and wiring free.
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
Are you using an off-shore switch or OEM? Wondering if an aftermarket swich an issue.
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
You may want to reread post #2. When you follow the melted wire you will find your problem. If the switch grounded you would see signs of it around where the switch goes through the dash.

Ok, thanksÂ…I just snooped on my lunch break and there's a crimp connector which connects the ign. Power to the switch and it's charred from the connector to the switch as you and Steve83 mentioned. Can the crimp connector by itself cause this? I can't see any bare spot on the wire that was next to the burned one like it shorted to its neighbor.
 

Attachments

  • 7F3E3543-EB72-4BC7-AE6C-9510CEC40915.jpg
    7F3E3543-EB72-4BC7-AE6C-9510CEC40915.jpg
    75.5 KB · Views: 120
Last edited:

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
An overheated connection can melt away the insulation, allowing a short to happen too. It's interesting that none of the strands of copper are broken or have any melted points anywhere.

I would use a meter and see if the short still exists somewhere. Its possible that the red wire on the butt splice is heaver guage and can handle higher current, but the splice from there to the switch was smaller and therefore got too hot.

Would be a good idea to trace what that wire is for.

Sent from my SM-G981U using Tapatalk
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
It's the ignition switch power supply, direct from the fuse box to the switch, except for the section of pigtail there at the switch. It's been running this way for years…that's what boggles my mind, but maybe it could have been rubbed raw at some spot and caused that pigtail piece to fry.
 
Top