Southbronco1
Jr. Member
- Joined
- Jan 19, 2021
- Messages
- 57
This great info above. Appreciate it guys. I ran out of time on Sunday, so headed back later this week and will use this spreader method above. Thanks for this tip.
This is great, thanksI made a spreader out of 1/2 inch bolt 4 1/2 inches long,4 grade 8 washers, and 2 grade 8 nuts. It worked great for me and it didn't hurt the hanger.
I called Tom's bronco and they said to face them with the open end facing forward and the closed end( the end with the brace) backward.I went through this same thing a couple weeks ago, all except your troubles with the bushings. Mine went in pretty well except that last 1/8" like yours but I used my Harbor Freight Ball Joint press with a 1/2" impact and no problemo. Also had the same thing with the Shackles and did the same trick using a bolt/nut/washer contraption to spread the ears of the shackle brackets just a tiny bit.
The instructions that come with the lift say install the shackles with the closed side facing forward but that doesn't work, at least not with those shackles. I think they're the Heavy duty replacement shackles. Mine were included with the lift kit I got. I wish that they'd add a note to the instructions saying something to the effect that "with these shackles, orientate them this was".
Nice rig BTW. Love the color. I asked about your lift because I am just replacing stock springs with no extra lift, and in this case it seems that Tom’s recommendation is for me to orient the shackles with the open side facing the back of the truck.It's a 9 leaf pack, 3.5 inch lift. I wish I went to a 2.5 inch lift, because I don't have doors , top, or rear tire carrier, and wright now it measure 4.5 inch and that's with 400 lbs of sand bags in back. I 'm hoping it will settle down or I may take out a leaf. T he front is WH 3.5 inch coils and wright now it measures at 4 inches, so no doors top and tire make a big difference on how high it really is to what the lift says.
I didn’t have the fortitude (or the tools) necessarily to remove that sleeve from the inside of the shackle, so I bought new shackles. Lolthe stock rubber bushings had a steel tube in the middle and a thin steel shell over the rubber on the outside. most of the time during disassembly the center tube and the rubber is driven the outer steel shell and the shell must be removed before new bushings are driven in. these thin shells are very hard to remove. some people remove them by hack sawing the shell i remove them by air hammer by driving the pointed bit between the shell and the spring. this folds the shell in a bit. then I change the tool in the air hammer to a panel ripper bit and kook that into the deformed shell and just drive it out. if this is not your problem then maybe your springs are not factory and changed in their past life.
Hey Rustytruck, he is not using the old shackles. He's using Toms new shackle, but I hear you on the OEM shackle bushings , they can be a pain and if the outer sleeve don't come out , and you don't realize it's still their when installing no bushings.the stock rubber bushings had a steel tube in the middle and a thin steel shell over the rubber on the outside. most of the time during disassembly the center tube and the rubber is driven the outer steel shell and the shell must be removed before new bushings are driven in. these thin shells are very hard to remove. some people remove them by hack sawing the shell i remove them by air hammer by driving the pointed bit between the shell and the spring. this folds the shell in a bit. then I change the tool in the air hammer to a panel ripper bit and kook that into the deformed shell and just drive it out. if this is not your problem then maybe your springs are not factory and changed in their past life.
Did you talk to someone, or did it finally come with instructionsNice rig BTW. Love the color. I asked about your lift because I am just replacing stock springs with no extra lift, and in this case it seems that Tom’s recommendation is for me to orient the shackles with the open side facing the back of the truck.
I talked with someone, but maybe I will call again just to double check. They might be tired of hearing from me. LolDid you talk to someone, or did it finally come with instructions![]()
I e-mailed them today to see if it really matters which way. I would really like to know, if we are getting two different answers from two different peopleI talked with someone, but maybe I will call again just to double check. They might be tired of hearing from me. Lol
Hey Paul, he is talking about aftermarket ones they sell. I sent them a picture of the ones on my 74, that had the aftermarket one from them. I think he's referencing his wife's bronco, which is stock and which way their oriented. I email him again, to make sure.Correct, but sounds like he’s talking about stock shackles. We’ve already determined the stock ones have the brace forward and the open end to the rear. I thought it was the aftermarket replacement shackles that were in question.
Hey Paul, jason from Tom's confirmed that you can mount them either way, open end front or back.Probably no need. You’re probably correct and at first I was assuming that all the Broncos they looked at probably had an aftermarket shackle like they sell. But at least for his wife’s bronco, which he said was all original, I felt he was referring to a stock shackle.






