• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear shackle bushing

OP
OP
S

Southbronco1

Jr. Member
Joined
Jan 19, 2021
Messages
57
This great info above. Appreciate it guys. I ran out of time on Sunday, so headed back later this week and will use this spreader method above. Thanks for this tip.
 

distended

Full Member
Joined
Feb 14, 2010
Messages
212
I went through this same thing a couple weeks ago, all except your troubles with the bushings. Mine went in pretty well except that last 1/8" like yours but I used my Harbor Freight Ball Joint press with a 1/2" impact and no problemo. Also had the same thing with the Shackles and did the same trick using a bolt/nut/washer contraption to spread the ears of the shackle brackets just a tiny bit.

The instructions that come with the lift say install the shackles with the closed side facing forward but that doesn't work, at least not with those shackles. I think they're the Heavy duty replacement shackles. Mine were included with the lift kit I got. I wish that they'd add a note to the instructions saying something to the effect that "with these shackles, orientate them this was".
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
I went through this same thing a couple weeks ago, all except your troubles with the bushings. Mine went in pretty well except that last 1/8" like yours but I used my Harbor Freight Ball Joint press with a 1/2" impact and no problemo. Also had the same thing with the Shackles and did the same trick using a bolt/nut/washer contraption to spread the ears of the shackle brackets just a tiny bit.

The instructions that come with the lift say install the shackles with the closed side facing forward but that doesn't work, at least not with those shackles. I think they're the Heavy duty replacement shackles. Mine were included with the lift kit I got. I wish that they'd add a note to the instructions saying something to the effect that "with these shackles, orientate them this was".
I called Tom's bronco and they said to face them with the open end facing forward and the closed end( the end with the brace) backward.
 

Attachments

  • Screenshot_20220228-204759_Samsung Internet.jpg
    Screenshot_20220228-204759_Samsung Internet.jpg
    112.5 KB · Views: 65
OP
OP
S

Southbronco1

Jr. Member
Joined
Jan 19, 2021
Messages
57
Savage, are you putting in a lift beyond the stock height? Or is this for stock height 5 leaf pack?
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
It's a 9 leaf pack, 3.5 inch lift. I wish I went to a 2.5 inch lift, because I don't have doors , top, or rear tire carrier, and wright now it measure 4.5 inch and that's with 400 lbs of sand bags in back. I 'm hoping it will settle down or I may take out a leaf. T he front is WH 3.5 inch coils and wright now it measures at 4 inches, so no doors top and tire make a big difference on how high it really is to what the lift says.
 

Attachments

  • DSCN2654.JPG
    DSCN2654.JPG
    322.5 KB · Views: 74
Last edited:

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
the stock rubber bushings had a steel tube in the middle and a thin steel shell over the rubber on the outside. most of the time during disassembly the center tube and the rubber is driven the outer steel shell and the shell must be removed before new bushings are driven in. these thin shells are very hard to remove. some people remove them by hack sawing the shell i remove them by air hammer by driving the pointed bit between the shell and the spring. this folds the shell in a bit. then I change the tool in the air hammer to a panel ripper bit and kook that into the deformed shell and just drive it out. if this is not your problem then maybe your springs are not factory and changed in their past life.
 
OP
OP
S

Southbronco1

Jr. Member
Joined
Jan 19, 2021
Messages
57
It's a 9 leaf pack, 3.5 inch lift. I wish I went to a 2.5 inch lift, because I don't have doors , top, or rear tire carrier, and wright now it measure 4.5 inch and that's with 400 lbs of sand bags in back. I 'm hoping it will settle down or I may take out a leaf. T he front is WH 3.5 inch coils and wright now it measures at 4 inches, so no doors top and tire make a big difference on how high it really is to what the lift says.
Nice rig BTW. Love the color. I asked about your lift because I am just replacing stock springs with no extra lift, and in this case it seems that Tom’s recommendation is for me to orient the shackles with the open side facing the back of the truck.
 
OP
OP
S

Southbronco1

Jr. Member
Joined
Jan 19, 2021
Messages
57
the stock rubber bushings had a steel tube in the middle and a thin steel shell over the rubber on the outside. most of the time during disassembly the center tube and the rubber is driven the outer steel shell and the shell must be removed before new bushings are driven in. these thin shells are very hard to remove. some people remove them by hack sawing the shell i remove them by air hammer by driving the pointed bit between the shell and the spring. this folds the shell in a bit. then I change the tool in the air hammer to a panel ripper bit and kook that into the deformed shell and just drive it out. if this is not your problem then maybe your springs are not factory and changed in their past life.
I didn’t have the fortitude (or the tools) necessarily to remove that sleeve from the inside of the shackle, so I bought new shackles. Lol
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
the stock rubber bushings had a steel tube in the middle and a thin steel shell over the rubber on the outside. most of the time during disassembly the center tube and the rubber is driven the outer steel shell and the shell must be removed before new bushings are driven in. these thin shells are very hard to remove. some people remove them by hack sawing the shell i remove them by air hammer by driving the pointed bit between the shell and the spring. this folds the shell in a bit. then I change the tool in the air hammer to a panel ripper bit and kook that into the deformed shell and just drive it out. if this is not your problem then maybe your springs are not factory and changed in their past life.
Hey Rustytruck, he is not using the old shackles. He's using Toms new shackle, but I hear you on the OEM shackle bushings , they can be a pain and if the outer sleeve don't come out , and you don't realize it's still their when installing no bushings.
can make it hard c
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Nice rig BTW. Love the color. I asked about your lift because I am just replacing stock springs with no extra lift, and in this case it seems that Tom’s recommendation is for me to orient the shackles with the open side facing the back of the truck.
Did you talk to someone, or did it finally come with instructions;)
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
I talked with someone, but maybe I will call again just to double check. They might be tired of hearing from me. Lol
I e-mailed them today to see if it really matters which way. I would really like to know, if we are getting two different answers from two different people😁
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
With most shackles, it really does matter. With the stock shackles the open side must face to the rear. With aftermarket shackles it’s up to the manufacturer.
You can test any brand or style of shackle before you install it on the spring just slip it into the spring hanger put a bolt through it and see if you get full travel. Flip it around and check again. In one direction there’s usually a lessening of overall travel.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
So Tom's bronco got Wright back, and I'll post the email. It sounds like it can be mounted either way.
 

Attachments

  • Screenshot_20220301-140930_Samsung Internet.jpg
    Screenshot_20220301-140930_Samsung Internet.jpg
    98.7 KB · Views: 91

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Correct, but sounds like he’s talking about stock shackles. We’ve already determined the stock ones have the brace forward and the open end to the rear. I thought it was the aftermarket replacement shackles that were in question.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Correct, but sounds like he’s talking about stock shackles. We’ve already determined the stock ones have the brace forward and the open end to the rear. I thought it was the aftermarket replacement shackles that were in question.
Hey Paul, he is talking about aftermarket ones they sell. I sent them a picture of the ones on my 74, that had the aftermarket one from them. I think he's referencing his wife's bronco, which is stock and which way their oriented. I email him again, to make sure.
 
Last edited:

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Probably no need. You’re probably correct and at first I was assuming that all the Broncos they looked at probably had an aftermarket shackle like they sell. But at least for his wife’s bronco, which he said was all original, I felt he was referring to a stock shackle.
 

BPerry

Full Member
Joined
Dec 7, 2021
Messages
168
I cussed the oem shackles sleeves for an hour and gave them the ole toss behind the shoulder just before ordering new HD ones "only because the others were out of stock"...

I did have to manipulate the hangers a bit and put the open end to the front to obtain full travel.
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
Probably no need. You’re probably correct and at first I was assuming that all the Broncos they looked at probably had an aftermarket shackle like they sell. But at least for his wife’s bronco, which he said was all original, I felt he was referring to a stock shackle.
Hey Paul, jason from Tom's confirmed that you can mount them either way, open end front or back.
Dave
 
Top