• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Using drum brake hubs for disc conversion?

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
Has anyone ever attempted to machine a stock drum brake front hub to use with a 76-77 rotor for disc brake conversion. Duffs use the stock hub with their budget kit with the rear machined to fit through the center of the rotor. Any thoughts on why this would or would not work with stick ford rotor???
 

Quick & Dirty

Sr. Member
Joined
Feb 15, 2004
Messages
857
I believe the hubs are the same but machined differently for drums or rotors. A new hub with rotor was always cheap enough to not be worth the effort. Quick search says $60-70 difference over just the rotor today so it may be worth the labor to machine the old hubs.

Go for it and let us know how it goes. I kept my drum hubs when I did the conversion to possibly do this myself at some point.
 

Cooper

Full Member
Joined
May 7, 2006
Messages
309
Loc.
Northeast
I recall seeing this discussed before but it has been awhile since I read about it. It was simple enough but involved creating a spacer by dimensioning a washer that was placed between the hub and spindle. I don't recall the specific dimensions and will have to sniff around to find any threads again. It is definitely possible as there were a couple recent threads where front disc brake kits by a company called Leeds (?) re-used the drum hubs, I believe by accounting for the thickness of the above mentioned spacer by using a caliper bracket cut from plate that added that thickness. Otherwise caliper brackets from the scrap yard, new hoses, calipers and pads just bolted on like any other disc brake swap. Perhaps someone who has done it will respond shortly.
 
Last edited:

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
spacer is not between the knuckle and spindle its on the stock spindle spacing out the new hub and rotor instead of buying a new spindle too.
 

stevew

Bronco Guru
Joined
Jun 21, 2001
Messages
2,123
Loc.
Elliston Montana
spacer is not between the knuckle and spindle its on the stock spindle spacing out the new hub and rotor instead of buying a new spindle too.
There was a pretty long thread way back on this . The sizing etc is there but I had several sets of spacers machined up to use the stock drum spindle .
As stated above , thats where it goes . I did this style of disk conversion once & it worked fine . I have 2 sets of spacers left if you want to go that route .
All you're saving by doing this is buying the different spindles , you still need the GM calipers & mounts/backing plates .
 
OP
OP
hunter1

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
I bought a complete GM Dana axle for the parts. Guy I bought it from said mid 70’s blazer or truck. After getting it apart I see that it’s the later 70’s model with the big inner spindle bearing, so can’t use the spindles unless I machine the bearing land down for the smaller Ford bearing??? Has anyone went this route? Caliper bracket is the one piece type and is in great shape.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I’ve turned big bearing spindles into small bearing, if you have the capability or access to an affordable shop it’s a very viable and simple option. The bearing spacing is the same, it is just a smaller diameter.

In my opinion for the cost of replacement hubs with rotors from several of the online suppliers it’s not worth the hassle of using a drum brake hub, all you are accomplishing is creating 1 off parts that a common everyday, available most everywhere part can replace.
 

Attachments

  • C540EFA2-2128-4FEC-B81C-F0C93F646097.jpeg
    C540EFA2-2128-4FEC-B81C-F0C93F646097.jpeg
    247.8 KB · Views: 113
  • DB05788E-3965-4E64-9E48-D92AFCF26FE9.jpeg
    DB05788E-3965-4E64-9E48-D92AFCF26FE9.jpeg
    238.8 KB · Views: 79
  • 20F079A9-0145-434F-AA80-12956D92CF69.jpeg
    20F079A9-0145-434F-AA80-12956D92CF69.jpeg
    156.9 KB · Views: 112
OP
OP
hunter1

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
I’ve turned big bearing spindles into small bearing, if you have the capability or access to an affordable shop it’s a very viable and simple option. The bearing spacing is the same, it is just a smaller diameter.

In my opinion for the cost of replacement hubs with rotors from several of the online suppliers it’s not worth the hassle of using a drum brake hub, all you are accomplishing is creating 1 off parts that a common everyday, available most everywhere part can replace.
Thanks for the info, I didn't see a reason it couldn't be done. You're right, I could buy it all together but I'm into it the cost of the axle so far, just looking for ways to cut cost. I have access to a lathe, so there wouldn't be a machining cost associated with it.
 
Top