• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel Gauge Selector Switch Orientation?

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Okay, so I am replacing my fuel gauge selector switch and want to make sure the wiring is correct.

I've searched and come up with two different images (below) of how the wires connect.

Two questions:

1) Are the wires connected on the row with straight or angled tabs?
2) I assume the correct orientation is angled tabs on top and straight on the bottom, as shown in both images?

fuel switch 1.JPG


fuel switch 2.jpg


Thanks!
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
The last one I did was like this. The main (orange wire) is on the passenger's side; aux (yelloe wire) on driver's side of switch.
 

Attachments

  • main on pass side.jpg
    main on pass side.jpg
    10.7 KB · Views: 205

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
The good news is that if you get it backwards from how you want it, you just reach up (easier said than done!) and reverse the order of the two outer ones.

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
So it almost seems like it doesn't matter? It's just a simple toggle switch and the straight and angled rows operate the same way?

I was hoping to make sure I had the aux and main tanks on the correct side to correlate to the switch, since I don't know how much fuel I have in either... Still trying to get the gauge to work correctly and was hoping it was the wire orientation.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yes, both rows work alike. Center pin is the signal from the gauge, either side is output to whichever sender at whichever tank it's connected to.
I always wanted to reverse mine, because it always pointed away from the reference I used from the driver's seat. Which was the lever/handle on the valve, not the actual pointer.
So mine was "correct" as installed from the factory, but I wanted to use the larger, easier to "feel" lever instead.

Sorry I can't remember the exact orientation, and don't have time to get a picture at the moment.
I'm sure someone will come up with one however.

In the meantime though, you can orient your switch thusly:
1. Note the position of the selector valve on the floor.
2. Decide whether you want the switch on the dash to match the pointer (correct0 or lever (optional).
3. Flip the lever to the position you choose.
4. Connect the wire to that tank to the "opposite" side connector on the back.

Now, this is just an old assumption on my part, so take it with a grain of salt (and go back to the previous comment about being able to swap the wires if needed) but I believe that the contact that is active at the time (closed) is the one opposite the switch position. Some switches work that way, some work the opposite.
So ignoring the wording on the bezel for the moment, if you flip the switch to the right, then the contact on the far left is the one connected to the center terminal.

Then whatever position the switch is in (left for MAIN and right for AUX?) match the lever on the valve the way you want. It's splined so you can remove and relocate it so that the lever OR the pointer is pointing the same way as the switch.
Whichever you prefer.

See? Simple.
Just make sure you have at least some gas in both tanks! That way if you get it backwards and run out of gas you can quickly switch to the other tank.:rolleyes:
Most of us got pretty good at quickly switching the tank valve on the fly when the engine started to sputter. ;)

Paul
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
So it almost seems like it doesn't matter? It's just a simple toggle switch and the straight and angled rows operate the same way?
Yes, each row is an SPDT switch that changes the center (Common) terminal between the 2 outboard terminals. Because there are 2 SPDTs in 1 housing, it's a DPDT switch, just like most other DPDTs. If you're only using it to change the gauge, you could replace it with a common SPDT. But to use it for an electric tank valve, it's easier with a DPDT.
 
Top