• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Liftgate latch roll pin question

Nowik35

Full Member
Joined
Aug 27, 2018
Messages
201
So another dumb mistake and now I need advice. So without thinking I installed my liftgate rod into the latch with a roll pin with a fully relaxed spring. I think that's wrong because now when I try to engage the handle the roll pin hangs up on the bracket to the right of the spring. Need help but I think I should have installed the roll pin to the right of the bracket with the spring compressed a little bit. Any ways, I need to take that roll pin out and I just can't grip it enough with needle nose pliers. Any advice how to remove this roll pin without destroying it? My only thought right now is drill it out?? Any advice would be greatly appreciated .
https://flic.kr/p/2oWWB3n
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Been so long I don't really remember how it's oriented. But the good news (at least from out here) is that a roll pin is easy to replace usually.
Unless it's something exotic, if you need to destroy it to get it out, a new one can be had.

I'm guessing it's not making it easy to remove the assembly to get better access to the pin?
Is the pin supposed to be behind the plate, or is it just too long and needs to be ground shorter so the spring can slide along the rod?

Trying to remember how it all works is hurting my brain! Must be too late...

Paul
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
I’m with Paul. Get an appropriate size punch and drive that puppy out of your way. Be easier on your nerve and fingers.

Randy
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
Here's an original before picture. Unfortunately my after picture didn't have enough light and was at a bad angle to see it. It looks like you installed it in the latch opening, not the pin opening. Either drill or hammer it at an angle with a punch to remove it.

IMG_6853.JPG
IMG_6847.JPG
IMG_4872.JPG
IMG_6855.JPG
 
Last edited:
OP
OP
Nowik35

Nowik35

Full Member
Joined
Aug 27, 2018
Messages
201
So I'm not understanding how I can get it out with a punch? The other side of the roll pin is the plate so I can't drive it through it needs to be backed out? Also where do I pin the rod so so when I press the handle the striker folds all the way in? Also should I be cutting the roll pin shorter? It seems way too long like it will hang up inside the window frame on the other side if I drive it flush with the hole im installing into?? Lol this is like the hardest part of putting my bronco back together smh
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
Okey-dokey, I’m going to crawfish here and say get a pair of needle-nosed locking pliers and lock it on the roll pin and “pull it out “ by hitting the bottom of the pliers. Sorry about the previous post.

Randy
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
So I'm not understanding how I can get it out with a punch? The other side of the roll pin is the plate so I can't drive it through it needs to be backed out? Also where do I pin the rod so so when I press the handle the striker folds all the way in? Also should I be cutting the roll pin shorter? It seems way too long like it will hang up inside the window frame on the other side if I drive it flush with the hole im installing into?? Lol this is like the hardest part of putting my bronco back together smh
Don't punch it straight (as you noted, you can't). Punch the top at an angle to push it over and through the oblong hole. Look at my earlier pictures with arrows that show you where to pin it.
 
OP
OP
Nowik35

Nowik35

Full Member
Joined
Aug 27, 2018
Messages
201
Ok so I took a little break from this aggravation to focus on other parts of the bronco but now I'm back I just need to fix these latches. So I took one side out just so I can study the mechanical and understand how it goes together and I think I have to disagree with you az73. Your pictures point to a hole for the dowel pin and I agree one does go in there but that's not the one that holds the rod secured to the mechanism. If you look at my pictures these two holes that dowel pins go into and hole number 2 in my picture is what holds the rod in place. I think. In my second picture when I place the rod it only goes in enough to clear hole number 2. Won't go up any further to use hole 1 to pin with. Which also explains when you buy replacement pins from BGY it comes with a set of 4 pins. Two for each latch. Anyways I think my initial install is correct I just think the pin is too long and it needs to be flush with the slit?? But also what does the pin in hole one serve a purpose for? It holds nothing in place.

https://flic.kr/p/2p2vhcs https://flic.kr/p/2p2vAzN
 

wrenchbender

New Member
Joined
Jul 14, 2014
Messages
6
Loc.
WNY
Roll Pin hole 1 is a stop so the Latch mechanism doesn't retract to far. In AZ73's second picture it is not installed yet. The actuator rod attaches with rollpin 2 outside of the bracket. When the tailgate lever is lifted it pulls the Latch in to release it. The Roll pin should be tight in the actuator rod and not the slot. The slot allows the Latch to compress when the tailgate is closed and spring back to lock in place.
Roll pin 1 should be shorter than the inside diameter of the spring.
 

moekerman

New Member
Joined
Dec 22, 2022
Messages
2

Nowik35, I am going trough the same headache now with some new liftgate latches from Toms. Could you send a picture of the final assembly?​

 
Top