• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New brake kits

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Proportioning valve is a terrible name because, unlike most things on a car, the name doesn't actually match what they do. I like to think of it as a pressure dampening valve. It is essentially there to allow brake bias to move more towards the front under heavy braking conditions to account for the fact that the front of the vehicle is being pushed down and the rear of the vehicle is being lifted up as the center of gravity tries to work its way over the front axle. I'm going to explain with very simple numbers to illustrate. Ignore my numbers above for now. Let's say that you have a 50/50 bias on paper (because you are a 96 F450 Super Duty and you have the same brakes on the front and the rear) and that you have a proportioning valve with a 50% reduction and it's set at 500PSI. If you press your brakes to the point that you get the PSI inside your calipers (both front and rear) to 400PSI, your proportioning valve is doing nothing and your brake bias is still 50/50. Now brake harder, let's say to 500PSI (just at the threshold that the proportioning valve is going to kick in); you will still have 50/50 bias. Now brake harder to the point that the front brakes have 600PSI. The rear brakes will now get reduced marginal pressure caused by the prop valve limiting the rear increased pressure by 50%, thus they will have only 550PSI (50% of the 100PSI that is over the 500PSI threshold) and the bias will be ~52/48 (600/1150 front and 550/1150 rear). Quick note, the only reason I can do the math on bias with just the caliper PSI is because the front and rear brakes are assumed to be identical so the bias is directly proportional to the caliper pressure. Moving on, let's brake harder, increasing the pressure in the front calipers to 700PSI. Now the backs have 600PSI and the bias is now~54/46. Now press the brakes with Iron Man's suit on so you raise the front caliper pressure to 1200PSI. The rears will now be at 850PSI and the bias will be ~58/42. I think you are getting the gist. The prop valve causes the bias to shift forward as you brake harder (over a given set threshold in the prop valve).

The "proportioning" comes from the fact that the increased force of your foot on the brake pedal has to go somewhere, and since the rear brakes will take less of an increase in pressure than the front, it must be sending that increased pressure to the front. I'm just accounting for that fact in that I'm measuring the resulting total pressure at the front first, and then deriving the pressure at the rear.

If you want to look at your particular case, your prop valve has infinite settings and a 57% reduction. I'll imagine you set your prop valve to kick in at 550PSI (which is reasonable) and you are using Eldo rears with FF pads front and back. Up to this point you will get the most bias to the back.

BrakesRotor SizePiston SizePiston CountPiston SADistance of piston center from edge of rotorPiston CoF DistanceCaliper PSIClamping ForcemuBraking ForceBraking Torque (lb*ft)Bias RearBias Front
Fronts (FF pads)
12.95​
2.2​
2​
7.60​
1.100​
5.3765​
550​
4181​
0.4​
3345​
1499​
Eldo rears (FF pads)
12.50​
2.5​
1​
4.91​
1.250​
5​
550​
2700​
0.4​
2160​
900​
37.5%​
62.5%​

Press the brakes harder and harder:

BrakesRotor SizePiston SizePiston CountPiston SADistance of piston center from edge of rotorPiston CoF DistanceCaliper PSIClamping ForcemuBraking ForceBraking Torque (lb*ft)Bias RearBias Front
Fronts (FF pads)
12.95​
2.2​
2​
7.60​
1.100​
5.3765​
700​
5322​
0.4​
4257​
1908​
Eldo rears (FF pads)
12.50​
2.5​
1​
4.91​
1.250​
5​
635.5​
3120​
0.4​
2496​
1040​
35.3%​
64.7%​
Fronts (FF pads)
12.95​
2.2​
2​
7.60​
1.100​
5.3765​
850​
6462​
0.4​
5170​
2316​
Eldo rears (FF pads)
12.50​
2.5​
1​
4.91​
1.250​
5​
721​
3539​
0.4​
2831​
1180​
33.7%​
66.3%​
Fronts (FF pads)
12.95​
2.2​
2​
7.60​
1.100​
5.3765​
1000​
7603​
0.4​
6082​
2725​
Eldo rears (FF pads)
12.50​
2.5​
1​
4.91​
1.250​
5​
806.5​
3959​
0.4​
3167​
1320​
32.6%​
67.4%​
Fronts (FF pads)
12.95​
2.2​
2​
7.60​
1.100​
5.3765​
1150​
8743​
0.4​
6994​
3134​
Eldo rears (FF pads)
12.50​
2.5​
1​
4.91​
1.250​
5​
892​
4379​
0.4​
3503​
1460​
31.8%​
68.2%​

You can see how the bias would shift forward in your specific case. Set the threshold lower and the bias will start shifting sooner. The idea is to set the threshold just to the point that the tires in the front lock first.
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Just FYI, here are the formulas
Clamping Force (lbs) = Caliper PSI / Piston SA inches square
Braking Force (lbs) = Clamping Force x Mu x 2
Braking Torque (ft*lbs) = Braking Force x Radial Distance in Inches to Center of Force / 12
Bias [front or rear] = Braking Torque [front OR rear] / (Braking Torque [front] + Braking Torque [rear])
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Something new to throw in the mix :) It's a Jeep application but hoping a 9" might be in the works from someone in the industry. https://brennans-garage.com/products/electric-emergency-brake-eebrake-rear-bracket-kit-41-75-jeep

FYI we are in the process of engineering something similar to this for all generations of Broncos. It will use a piston larger than 2", 13" rotors and come with either a manual or electric integrated parking brake. Keep an eye on www.hugebrakes.com over the coming weeks.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Just FYI, here are the formulas
Clamping Force (lbs) = Caliper PSI / Piston SA inches square
Braking Force (lbs) = Clamping Force x Mu x 2
Braking Torque (ft*lbs) = Braking Force x Radial Distance in Inches to Center of Force / 12
Bias [front or rear] = Braking Torque [front OR rear] / (Braking Torque [front] + Braking Torque [rear])
Can you please run the 2003-2006 Jeep Wrangler Rubicon piston and radius numbers in your spreadsheet? That would provide a reasonable empirical analogue for a 93 inch wheelbase, high CG, Live Axle, disc/disc vehicle typically running 33 inch tires, and zero proportioning hardware. I want to be consistent for COF, and don't know how you derive it.

Pistons: 66mm front, 48mm rear, (2.60 inch, 1.89 inch)
Rotors: 280mm front, 285mm rear. (11.02 inch, 11.22 inch)
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
BrakesRotor SizePiston SizePiston CountPiston SADistance of piston center from edge of rotorPiston CoF DistanceCaliper PSIClamping ForcemuBraking ForceBraking Torque (lb*ft)Bias RearBias Front
Fronts (FF pads)
11.02​
2.6​
1​
5.31​
1.300​
4.21​
550​
2920​
0.4​
2336​
820​
Rears (FF pads)
11.22​
1.89​
1​
2.81​
0.945​
4.665​
550​
1543​
0.4​
1234​
480​
36.9%​
63.1%​
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
I am not worthy...
 

Attachments

  • not worthy.jpg
    not worthy.jpg
    26.6 KB · Views: 142

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
☺️ You are welcome! Anything I can do to help y'all keep the shinny side up and the greasy side down.

If you feel like paying back the favor, I'd love some feedback on our Huge Brakes kits that we just brought to the market. Best I can tell, 259 of the users of this site have visited our store. Clearly we have made an impression. I'd love to know what that impression is, what you like, what you don't like, and what we can do to get people to adopt our kits.

We are currently making further investment in developing products. By the end of the year we will have Huge Brakes kits available for Gen 1 through Gen 5 Broncos. We are also rapidly developing a Huge Brakes kit for the rear that will use massive rotors and calipers and include an electric parking brake. That will also be a complete bolt on kit for the Gen 1 through Gen 5 Broncos. That development arose out of the concern around brake bias that users of this site brought up some time back, so we are putting together a kit that will make bias 35/65.

The people who have our kits installed (just 2 so far) are really impressed the stopping power; my Gen 3 with 37s and an iron headed 460 now stops better than my Gen 6 Sasquatch. What do you suggest I do to get more people to adopt? Be frank with me, please. It will only help guide our development and products in ways that have the best impact on your experience.

www.hugebrakes.com

Thanks in advance!
 

duffymahoney

Contributor
Bronco Guru
Joined
Apr 26, 2015
Messages
2,734
Honestly I want a modern aluminum style caliper. Something like the svt swap or whatever. Have a 15, 16 and 17" wheel option. Ebrake seperate like my 240z brake kit. Then I don't have to design and make it:) There are so many cars with this style brake caliper, which on a high end bronco build, I see as the go to.

I dislike wilwood stuff, so any other brand would be neat. Brembo? I know the Subaru and SVT are Brembo.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
@LittleBeefy Thanks again for the time, energy and detail provided.

one that I know a few of us running 1 ton axles would like to see is a plastic reservoir master cylinder that fits under the hood of our trucks with a stock style angled bracket. I'd love to get away from the leak prone cast iron/tin lid one I'm running that has made a dimple in my hood.
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
@LittleBeefy Thanks again for the time, energy and detail provided.

one that I know a few of us running 1 ton axles would like to see is a plastic reservoir master cylinder that fits under the hood of our trucks with a stock style angled bracket. I'd love to get away from the leak prone cast iron/tin lid one I'm running that has made a dimple in my hood.

Something I have been considering is custom aluminum inserts for the MC with a hose nipple to replace the plastic reservoir all together and allow use of a remote mounted reservoir. Is that something that would interest you?
 

gunnibronco

Contributor
Sr. Member
Joined
Apr 13, 2008
Messages
628
Loc.
Gardnerville, NV
☺️ You are welcome! Anything I can do to help y'all keep the shinny side up and the greasy side down.

If you feel like paying back the favor, I'd love some feedback on our Huge Brakes kits that we just brought to the market. Best I can tell, 259 of the users of this site have visited our store. Clearly we have made an impression. I'd love to know what that impression is, what you like, what you don't like, and what we can do to get people to adopt our kits.

We are currently making further investment in developing products. By the end of the year we will have Huge Brakes kits available for Gen 1 through Gen 5 Broncos. We are also rapidly developing a Huge Brakes kit for the rear that will use massive rotors and calipers and include an electric parking brake. That will also be a complete bolt on kit for the Gen 1 through Gen 5 Broncos. That development arose out of the concern around brake bias that users of this site brought up some time back, so we are putting together a kit that will make bias 35/65.

The people who have our kits installed (just 2 so far) are really impressed the stopping power; my Gen 3 with 37s and an iron headed 460 now stops better than my Gen 6 Sasquatch. What do you suggest I do to get more people to adopt? Be frank with me, please. It will only help guide our development and products in ways that have the best impact on your experience.

www.hugebrakes.com

Thanks in advance!
I really appreciate the info you've provided and calculations on my Frankenstien set up.

I have another EB to upgrade to disk fronts soon, but it will remain on stock 15" wheels. I have everything accumulated to do an F150 knuckle swap. It' will be a stockish patina LUBR so I'm not going to need anything performance oriented.

Right now I'd like an electric e-brake alternative to the common 1-ton rear disk swap we've been discussing .I can't easily run an e-brake cable set and don't love the idea and price of the electronic cable actuators I've seen. Ideally, just a caliper that fits the generic aftermarket brackets with the common rotor. I know that's probably an unrealistic request. If you could come up with a rotor, hanger and caliper with electric ebrake that would be cool too. If the rotor didn't hang out past my tires that would be ideal. I've already impacted the disk at least once because off the rotor offset from the hub. It's probably not your ideal target market and might not offer the potential customer base, but most people bitch about the Eldo caliper's e-brake. I'm not sure if those complaints are about both the larger 76-78 Eldo caliper or just the smaller Eldo calipers. This is new territory for me.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Something I have been considering is custom aluminum inserts for the MC with a hose nipple to replace the plastic reservoir all together and allow use of a remote mounted reservoir. Is that something that would interest you?
For some of the vehicles I've built most definitely. In those I wound up using Wilwood crap just because they offered what was needed and not what we wanted LOL. In the street rod and race car markets there is definitely a need. However, for my bronco not really, they would have to be mounted lower than the master, I have a very space challenged engine bay were everything is built around everything.... just a nice short reservoir like what is available on some of the cars and vans, the bore on them is just too small to get the brakes to have reasonable pedal travel, if they even apply the brakes at all.

this is the end of the MC right above the spring tower, the hood is just a wee bit closer on the top. I didn't plan this portion of the build very well. My original plan as to move it over to the driver's side some and not use the factory style angle bracket but the alternator got in the way. Even looked at putting in an under-floor unit, not really an option either since I lowered the floors under the seat to lower the seats and cut the rockers off to raise the rockers... nothing about this is normal and in no way am I looking for someone to build something one off just for it, but if it is something someone sees value in, I'm all for it. I do happen to know I'm not the only one that has complained, the solutions they came up with just weren't short enough for my application.
 

Attachments

  • pic.jpg
    pic.jpg
    178.4 KB · Views: 91

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Honestly I want a modern aluminum style caliper. Something like the svt swap or whatever. Have a 15, 16 and 17" wheel option. Ebrake seperate like my 240z brake kit. Then I don't have to design and make it:) There are so many cars with this style brake caliper, which on a high end bronco build, I see as the go to.

I dislike wilwood stuff, so any other brand would be neat. Brembo? I know the Subaru and SVT are Brembo.

I have an aluminum 6 piston kit that is ready to go to market. It uses a caliper that SSBC will be releasing (hopefully) at the SEMA show. The cost of that kit would be around $2200. It requires 17” wheels because it uses a 13.25” rotor. It is going to be a bad-ass setup and will look phenomenal too.

I have toyed with the idea of adapting an American Power Brakes caliper. I know I could make it work, but that would come in around $3500. Also, there is a Baer 6P option that I could make work with 13”+ rotors, but also would come in around $3500. Using a Brembo setup would cost around $6000. All of these require 17”+ wheels. Are there any hand raisers out there that want to spend that much money? If so, I'm ready to make your Bronco the prototype; I'm holding for crickets hahaha.
@duffymahoney while Wilwoods don’t generally have very large pistons, the D8-4 kit that fits under the 15” is arguably the best of their breed in terms of clamping force. The price is pretty reasonable for an aluminum caliper. What is it that you dislike about their setup that makes you wish there was a different option?
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
For some of the vehicles I've built most definitely. In those I wound up using Wilwood crap just because they offered what was needed and not what we wanted LOL. In the street rod and race car markets there is definitely a need. However, for my bronco not really, they would have to be mounted lower than the master, I have a very space challenged engine bay were everything is built around everything.... just a nice short reservoir like what is available on some of the cars and vans, the bore on them is just too small to get the brakes to have reasonable pedal travel, if they even apply the brakes at all.

this is the end of the MC right above the spring tower, the hood is just a wee bit closer on the top. I didn't plan this portion of the build very well. My original plan as to move it over to the driver's side some and not use the factory style angle bracket but the alternator got in the way. Even looked at putting in an under-floor unit, not really an option either since I lowered the floors under the seat to lower the seats and cut the rockers off to raise the rockers... nothing about this is normal and in no way am I looking for someone to build something one off just for it, but if it is something someone sees value in, I'm all for it. I do happen to know I'm not the only one that has complained, the solutions they came up with just weren't short enough for my application.

If you had your druthers, what aluminum MC would you use? Would it be one of the late 80s to early 2000s Fords or a GM one? Does it have to have a bore larger than 1.25”? Would you want a 1 7/16” from an early 2003-07 GM 1 ton van (if I could address the problem with the height of the reservoir)? Would you use it if it had a long, wide, flat reservoir instead of the tall ones? Do you care if the reservoir is plastic or aluminum?
 

duffymahoney

Contributor
Bronco Guru
Joined
Apr 26, 2015
Messages
2,734
I have an aluminum 6 piston kit that is ready to go to market. It uses a caliper that SSBC will be releasing (hopefully) at the SEMA show. The cost of that kit would be around $2200. It requires 17” wheels because it uses a 13.25” rotor. It is going to be a bad-ass setup and will look phenomenal too.

I have toyed with the idea of adapting an American Power Brakes caliper. I know I could make it work, but that would come in around $3500. Also, there is a Baer 6P option that I could make work with 13”+ rotors, but also would come in around $3500. Using a Brembo setup would cost around $6000. All of these require 17”+ wheels. Are there any hand raisers out there that want to spend that much money? If so, I'm ready to make your Bronco the prototype; I'm holding for crickets hahaha.
@duffymahoney while Wilwoods don’t generally have very large pistons, the D8-4 kit that fits under the 15” is arguably the best of their breed in terms of clamping force. The price is pretty reasonable for an aluminum caliper. What is it that you dislike about their setup that makes you wish there was a different option?
I have had multiple wilwood fail out of the box, MC, calipers. I think they just got big, and miss stuff.

I meant CTS-V calipers, which is the go to for a lot of tuners.

The stuff is cheap. Sub 500 for fronts, tons of companies use them, or the WRX caliper set. https://www.ebay.com/itm/1712467857...d=link&campid=5335857059&toolid=20001&mkevt=1

I like this style of ebrake.

Brand new from rock auto is 139 a caliper! https://www.rockauto.com/en/moreinfo.php?pk=8327508&cc=0&pt=1704&jsn=3
 

Attachments

  • BR-6PX-6002A.jpg
    BR-6PX-6002A.jpg
    433.6 KB · Views: 149

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
If you had your druthers, what aluminum MC would you use? Would it be one of the late 80s to early 2000s Fords or a GM one? Does it have to have a bore larger than 1.25”? Would you want a 1 7/16” from an early 2003-07 GM 1 ton van (if I could address the problem with the height of the reservoir)? Would you use it if it had a long, wide, flat reservoir instead of the tall ones? Do you care if the reservoir is plastic or aluminum?
1.25 is the minimum bore with 1.375 the maximum. GM would be the preferred since it fits the most boosters. One from the van would work well too but would require hydro boost, which is doable and many in my situation already have it. I don’t think reservoir material maters, as for shape, don’t care either as long as it doesn’t leak.

I haven’t gone hydro boost out of not wanting to design a new power steering reservoir and to change the pump. Currently running a pump for a CTS-V with the matching reservoir. It works fine but the pump barely keeps up at low rpm, parking lots can be borderline frustrating, get it above idle and it’s fine. But the pump is designed to power a rack… not a box with assist. I just feel adding hydro will aggravate that.

Funny that you brought up the early 2000’s van. My “other” truck uses hydro boost and master from an 03 3500 van. Pushing typical GM 3” calipers and 11” ford drums. It works great, but the pedal barely moves and is hard, I like it just fine, it just feels different.

As you can see there is some, errrr, ummm different stuff going on
 

Attachments

  • IMG_2352.jpeg
    IMG_2352.jpeg
    243.8 KB · Views: 114
  • IMG_2744.jpeg
    IMG_2744.jpeg
    269.5 KB · Views: 126
Last edited:
OP
OP
toddz69

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
I have had multiple wilwood fail out of the box, MC, calipers. I think they just got big, and miss stuff.

I meant CTS-V calipers, which is the go to for a lot of tuners.

The stuff is cheap. Sub 500 for fronts, tons of companies use them, or the WRX caliper set. https://www.ebay.com/itm/1712467857...d=link&campid=5335857059&toolid=20001&mkevt=1

I like this style of ebrake.

Brand new from rock auto is 139 a caliper! https://www.rockauto.com/en/moreinfo.php?pk=8327508&cc=0&pt=1704&jsn=3
I really like those calipers too - and they're really popular for some of the newest Fox body conversions but I feel those calipers are all too small for the front of our heavy rigs. Perhaps @LittleBeefy may have other feelings but I think calipers with total piston areas in the low-mid 4" sq.in. range are too small.

Todd Z.
 
OP
OP
toddz69

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
☺️ You are welcome! Anything I can do to help y'all keep the shinny side up and the greasy side down.

If you feel like paying back the favor, I'd love some feedback on our Huge Brakes kits that we just brought to the market. Best I can tell, 259 of the users of this site have visited our store. Clearly we have made an impression. I'd love to know what that impression is, what you like, what you don't like, and what we can do to get people to adopt our kits.

We are currently making further investment in developing products. By the end of the year we will have Huge Brakes kits available for Gen 1 through Gen 5 Broncos. We are also rapidly developing a Huge Brakes kit for the rear that will use massive rotors and calipers and include an electric parking brake. That will also be a complete bolt on kit for the Gen 1 through Gen 5 Broncos. That development arose out of the concern around brake bias that users of this site brought up some time back, so we are putting together a kit that will make bias 35/65.

The people who have our kits installed (just 2 so far) are really impressed the stopping power; my Gen 3 with 37s and an iron headed 460 now stops better than my Gen 6 Sasquatch. What do you suggest I do to get more people to adopt? Be frank with me, please. It will only help guide our development and products in ways that have the best impact on your experience.

www.hugebrakes.com

Thanks in advance!
I haven't purchased anything, but I am pleased that you've invested a lot of time and tech bringing these kits to market. Now I have somewhere to send people when they say they want front brakes like mine :). I like that you've rounded up many of the currently available kits for our trucks all in one spot - it gives people a lot of options. And I'll second/third all the computational work you've done for us in terms of brake biasing. Looking forward to what else you bring to market!

Todd Z.
 
Top