• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear shackle help

OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
The more that I think about it, the more I think this may be wrong. Unless facing it this way is to limit forward travel of the shackle.
c389eb8af8048ba1a5d9d8fb73015516.jpg


Sent from my Pixel 3 XL using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
It does look like that particular shackle is designed to go in the reverse position of how it is in the picture.
They are supposed to be able to rotate farther forward than that.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Backwards. But now you are good at it.
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I really wish I would have reached out earlier and not fought with this thing for hours. With a fresh mind and good info from here I have removed and correctly installed the driver side and installed the passenger side in about 30 minutes.

Sent from my Pixel 3 XL using Tapatalk
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I installed the front first.

Sent from my Pixel 3 XL using Tapatalk
I typically find it easier to install the shackle side first. You can wiggle the spring around to get the shackle lined up. Then that holds the back of the spring in place as you jam the front into place. Leave all the nuts loose so you can wiggle the springs side to side to get the centering bolts dropped into the axle housing).

Can't comment on the aftermarket shackle and how it faces. It might be backwards from stock, and the instructions might be written for a stock shackle?
 

hsach

Contributor
Members Only
Joined
Apr 19, 2013
Messages
435
Another method for lining up the bolt hole is using a ratchet strap. I went through everything the OP did. Had to open the shackle mount a little, still didn't sit all the way down. About a 1/4" off. Use a block of wood directly under the shackle mount, then slowly suck it down with the strap. I did it without the leaf spring attached to the shackle to test it out, and then with the spring attached. Went smoothly each time and no worry about messing up your bolt threads!
20230214_192141.jpg
 

magstar67

Jr. Member
Joined
Nov 26, 2011
Messages
60
Loc.
Missouri
The more that I think about it, the more I think this may be wrong. Unless facing it this way is to limit forward travel of the shackle.
c389eb8af8048ba1a5d9d8fb73015516.jpg


Sent from my Pixel 3 XL using Tapatalk
Sorry to revive an old thread but I’m going thru this exact situation. Tom’s instructions say to mount the shackle this way I think (they have zero pics in them) but the lower face of the shackle hits the perch this way. Have you had any issue with the shackle turned the other direction???
 

Attachments

  • IMG_9064.jpeg
    IMG_9064.jpeg
    66.4 KB · Views: 148
  • IMG_9065.jpeg
    IMG_9065.jpeg
    122.4 KB · Views: 150
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
Sorry to revive an old thread but I’m going thru this exact situation. Tom’s instructions say to mount the shackle this way I think (they have zero pics in them) but the lower face of the shackle hits the perch this way. Have you had any issue with the shackle turned the other direction???
The picture is incorrect orientation. The open end of the Tom's shackle goes forward. It's opposite of stock.

I had lots of issues with my installation due to the instructions being too vague in my opinion. They've been selling these parts for a long time. The instructions could have been a lot better.
 

magstar67

Jr. Member
Joined
Nov 26, 2011
Messages
60
Loc.
Missouri
Sorry to revive an old thread but I’m going thru this exact situation. Tom’s instructions say to mount the shackle this way I think (they have zero pics in them) but the lower face of the shackle hits the perch this way. Have you had any issue with the shackle turned the other direction???

The picture is incorrect orientation. The open end of the Tom's shackle goes forward. It's opposite of stock.

I had lots of issues with my installation due to the instructions being too vague in my opinion. They've been selling these parts for a long time. The instructions could have been a lot better.
Ok thanks. A couple of pics in their instructions would save a lot of time and confusion!
 

Brush Hog

Full Member
Joined
Mar 16, 2022
Messages
241
Loc.
NorCal
I usually just call the vendor. Tom’s,WH,duffs are all super helpful with tech support/install input and info whenever I’ve run into a problem (which is usually me over thinking the situation).
 
OP
OP
J

Jonathan_Cole

Full Member
Joined
May 11, 2020
Messages
154
I usually just call the vendor. Tom’s,WH,duffs are all super helpful with tech support/install input and info whenever I’ve run into a problem (which is usually me over thinking the situation).
I'd agree for the most part. Except when you are doing these projects over the weekend.

I'm not here to bash Tom's. But, as I said before, after all these years of selling parts, instructions could be a lot better.

Phone calls and emails were always handled quickly. But, that's not always an option.

The instructions were not my biggest issue either. I could have saved hundreds of dollars if someone would have asked a few more questions when they called to confirm my order.

I also could have saved a lot of headaches if some of the parts would have been sent correctly the first time.
 

m_m70

Contributor
Bronco Guru
Joined
Jun 14, 2001
Messages
1,770
Loc.
Prescott AZ
I'm not here to bash Tom's. But, as I said before, after all these years of selling parts, instructions could be a lot better.
Yeah I try to support all of our vendors but I agree that it shouldn't take years to fix or even just add clarity to instructions.
 

lindsaywyn

Contributor
New Member
Joined
Aug 26, 2022
Messages
42
So sorry to revive an old thread.. again... but Jonathan, this thread is making me feel less crazy... i have spent HOURS today having the same issue and finally found this conversation. I've wasted a hole dang day trying to fight these and I will now be fixing it tomorrow... THANK you! I will be leaving a review on Toms with this input for the next sorry soul that buys them :)
 
Top