• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Suspension mock up need grease?

joshua

Contributor
Bronco Guru
Joined
Jun 5, 2007
Messages
1,764
I’m mocking everything up on the frame for suspension and drivetrain before I paint the frame. Need to weld a few more suspension pieces on.

My question is, I’m at the c bushings and I’m wondering do I need to grease the c bushings and torque everything down? I’m just trying to figure out shock placement and making sure I have all the pieces to complete the frame, suspension and drivetrain portion of my bronco.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
Yes, can't remember the name but I use a specialty grease made specifically for polyurethane. SUPER-sticky lube.

Look on line, it works
 
OP
OP
joshua

joshua

Contributor
Bronco Guru
Joined
Jun 5, 2007
Messages
1,764
Yes, can't remember the name but I use a specialty grease made specifically for polyurethane. SUPER-sticky lube.

Look on line, it works
So even for just mockup I should grease it up. Everything is coming back apart to paint. I kinda of thought that. But was just making sure
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,223
I think grease would be very beneficial for putting the front end together, even though it's coming apart.

I like Super Lube - I'm convinced it's what all the suspension manufacturers put in their little installation tubes and tubs and mark up accordingly.

Todd Z.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
OMG, I would have blindly gone down the same rabbit hole!! lol

:)
 
OP
OP
joshua

joshua

Contributor
Bronco Guru
Joined
Jun 5, 2007
Messages
1,764
If I didn’t before, there’s no way now that I don’t have an FBI profile. Thanks nvrstuk!
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
I get guys in trouble all the time, but usually not like this LOL
 
OP
OP
joshua

joshua

Contributor
Bronco Guru
Joined
Jun 5, 2007
Messages
1,764
I get guys in trouble all the time, but usually not like this LOL
I was looking through my lube collection, is this it?
 

Attachments

  • IMG_4759.jpeg
    IMG_4759.jpeg
    170 KB · Views: 91

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
You don’t happen to still have the old rubber bushings laying around by any chance, do you? If not, and you happen to have a little time, you can get a new set for pretty cheap and use them for your mock up.
That way, no lubrication necessary, and you can put things together and take it apart multiple times without deforming the bushings.
Polyurethane bushings like to squeeze out and get “pushed” so to speak. Doesn’t make them useless after one run, but it does affect them.
Hence the almost universal agreement about using lubrication of some kind on them before installing.

And by all means, if you are coating the pads where the c-bushings go, don’t use the thick powder coat or POR15 kind of product. The tolerances are so tight, the extra few thousandths of material just makes the bushings that much harder to install, and that much more prone to deformation.
 
OP
OP
joshua

joshua

Contributor
Bronco Guru
Joined
Jun 5, 2007
Messages
1,764
You don’t happen to still have the old rubber bushings laying around by any chance, do you? If not, and you happen to have a little time, you can get a new set for pretty cheap and use them for your mock up.
That way, no lubrication necessary, and you can put things together and take it apart multiple times without deforming the bushings.
Polyurethane bushings like to squeeze out and get “pushed” so to speak. Doesn’t make them useless after one run, but it does affect them.
Hence the almost universal agreement about using lubrication of some kind on them before installing.

And by all means, if you are coating the pads where the c-bushings go, don’t use the thick powder coat or POR15 kind of product. The tolerances are so tight, the extra few thousandths of material just makes the bushings that much harder to install, and that much more prone to deformation.
I think j do have them. Thanks!
 
Top