Twin stick shift knobs

[Bitch'nBronco]

Show off your shift knobs. I've decided to shorten my JbFab twin sticks and figured this would be a good opportunity to put some different shift knobs on since I'm going to be cutting new threads.

 

[JB Fab]

We can do that for you if you want, including bends....the 205 shifters are sized for a truck or a FSB.

Jon

 

[Yeller]

Here’s mine. Got them from Duff’s. I did have to drill and tap them, they were 3/8”, needed 1/2” for my atlas shifter. I got them several years ago, not sure if they still have them. I know they were discussing making an insert that would allow multiple thread sizes in the same knob without drilling and tapping.

 

[Howard2x4x4]

I know they were discussing making an insert that would allow multiple thread sizes in the same knob without drilling and tapping.

That would be slick!

 

[Bitch'nBronco]

We can do that for you if you want, including bends....the 205 shifters are sized for a truck or a FSB.

Jon

Thanks Jon, I'll shoot you a PM.

 

[tasker]

BOOM and bigger boom

 

[eBronc2]

For my first set of twin sticks, I used cue balls, drilled and tapped.

When I upgraded to JB stainless twin sticks, I'm looking for something sort of tall and thin, to better fit the slot in the 2022 Bronco center console.

 

[MarsChariot]

Since I am keeping a more classic look, I went with WH billet knobs and paired that with a short throw B&M NV3550 shifter. Made my own labels because all the commercial ones are tiny, hard to see, and don't have the right look.

 

[Howard2x4x4]

Looks great Mr. Mars!

 

[Bitch'nBronco]

BOOM and bigger boom View attachment 931466

Looks like a TCI slap shifter for an 05-09 Mustang. Great shifter! Love the Frags

 

[Bitch'nBronco]

For my first set of twin sticks, I used cue balls, drilled and tapped.

View attachment 931470

When I upgraded to JB stainless twin sticks, I'm looking for something sort of tall and thin, to better fit the slot in the 2022 Bronco center console.

View attachment 931471 View attachment 931472

Console looks great in there, I like the 6G hvac vents in the dash

 

[eBronc2]

Console looks great in there, I like the 6G hvac vents in the dash

Thanks. I wanted to clean up and simplify the dash, going with Vintage Air HVAC so I was able to get rid of the ash tray, radio hole, speaker grill, and all the heater/defrost/fan knobs. Centered the speedo, relocated the glove box door, and spaced the vents to clear rollcage downbars on both sides. Only switches on the dash now are ignition, lights, wipers, and hazards.

I lucked out with the 6G console, the stock shifter/drivetrain mode cutout worked great for the twin sticks, and the ZF shifter comes up though the coin tray/phone charger recess. Cup holders are a bonus.

 

[Scoop]

I have a Northwest Fab Blackbox doubler that came with a turned aluminum knob. I liked it so I ordered 2 more knobs for my twin sticks so that they all matched.

 

[EPB72]

WH/jb fab I bent the levers a little and flattened out the knobs where they bypass each other.

 

[powers4680]

Sent from my iPhone using Tapatalk

 

[FORD*DIEHARD]

.

 

[migs]

I went happy on the transmission shifter and just a couple plain round knobs on the twin sticks..... danger, don't pull the red lever!

 

[tasker]

I went happy on the transmission shifter and just a couple plain round knobs on the twin sticks..... danger, don't pull the red lever!
View attachment 931550 View attachment 931551 View attachment 931552

WISH IT was cleaner though.....

 

[mustanggarage]

I like these billet ones from jb fab and my Hurst knock off transmission shifter

 

[Johnnyb]

For my first set of twin sticks, I used cue balls, drilled and tapped.

View attachment 931470

When I upgraded to JB stainless twin sticks, I'm looking for something sort of tall and thin, to better fit the slot in the 2022 Bronco center console.

View attachment 931471 View attachment 931472

@eBronc2 what tranny is that? Great dash, BTW! Love the center instrumentation.

-JB