• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

The Ballad of Ol' Rusty

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I would pull the thermostat, connect a garden hose to the heater hose in the intake and let it run for a while with the lower radiator hose is disconnected.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
I would pull the thermostat, connect a garden hose to the heater hose in the intake and let it run for a while with the lower radiator hose is disconnected.

I did that for awhile last night. After about 5 minutes it started to flow clear.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
A little more progress was made today.

Over lunch I changed out the transfer case oil. I had assumed it would be choclate-milk-esque. However, it was really clean. I am not sure, but I think it might have been ATF. It was red and significantly thinner that the gear oil I put back in it. Changing it did not help in reducing the whining and vibration that seems to be coming from it. When I took it for a spin around the block this evening it popped out of gear again.


 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
I let Ol Rusty idle in the driveway awhile tonight. The temp got up to 170, but that was all. I drained the water again. That would be the 4th cycle through of clean water. This time, the water was pretty clean when it came out. So, next time I do it, I will be running some cleaning product through the system.


Now that the engine at least keeps itself cool, I am able to look into other issues. In order to start Ol Rusty, I have to pour a little gas in the carb. It fires right up and will idle ok after that. If you kill it or turn it off, you have to go prime the carb with gas to start it again. So I assume a carb rebuild kit is in my future. My research this evening tells me that I have a Motorcraft 2150. Let me know if I am wrong.
1755919505585.png

1755919534057.png




Here is how it was acting once it is running:

 

Lawndart

Sr. Member
Joined
Nov 23, 2014
Messages
958
Loc.
66030
1) Are you in low gear in your transfer case?
2) Doesn't look like your carb accelerator pump is getting actuated.

EDIT - looks like you may have uncapped vacuum ports behind the carb as well.
 

El Kabong

Contributor
Driving stuff Henry built
Joined
Oct 8, 2009
Messages
1,559
Doesn't look like your carb accelerator pump is getting actuated.
x2. It doesn't look like the accelerator pump arm is moving enough. Maybe the linkage isn't connected correctly.

From another recent thread, cause I'm to sleepy to write it again. 🥱
I wonder if your accelerator pump isn't working. It gives an extra squirt of fuel as you open up the throttle. Vacuum drops as you open the throttle, which throws off the fuel pulling through normal circuits. That extra squirt carries you through that transition.

With the key off, remove the air filter, hold the choke open, look down into the carb, and open the throttle. Watch & see if you get a steady stream of fuel into the venturis as you move the throttle. It should squirt fuel while the throttle is moving toward open as long as there is fuel in the bowl.

If it works, your problem is elsewhere. If not, the accelerator pump is bad, the linkage to it isn't right, or a passage is blocked.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
One possible way to check for a lean condition, would be to pull the PCV valve out of the valve cover and put your finger over it. Yes, it’s a controlled vacuum leak that is supposed to be there, but right now you’re trying to find out if it’s too lean to begin with.
So just plug that one off and see what changes.

Also, which type of vacuum is hooked to the vacuum advance? I know you mentioned what port it’s on, but I’m not good with ports. Just tell me whether it’s ported or full manifold vacuum.
One reason I ask, is that when using full manifold, as you accelerate, the timing goes down at least momentarily.
So if your mechanical timing is set too low, and your vacuum advance lets off too much, you can get stumbling.
There are certainly situations where full manifold vacuum works best. But it requires a different bit of tuning.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
The transfer case popping out of gear is either a collapsed detent spring or worn output shaft bearings in the transfer case. Both can be fixed without a rebuild. Transmission fluid in the tcase points to a leaky adapter seal between the transmission and transfer case. Did you notice if the transfer case was over full?
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
The transfer case popping out of gear is either a collapsed detent spring or worn output shaft bearings in the transfer case. Both can be fixed without a rebuild. Transmission fluid in the tcase points to a leaky adapter seal between the transmission and transfer case. Did you notice if the transfer case was over full?

I did not check if the transfer case was overfull. I will say it seemed like it was 100% ATF not just some red tint to gear oil. But I could definately be wrong about that as I did have to add Fluid to the tranny. (I honestly dont remember what the floor looked like under the bronco where it had been parked for 20 years.


Tell me more on these transfer case fixes.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
x2. It doesn't look like the accelerator pump arm is moving enough. Maybe the linkage isn't connected correctly.

From another recent thread, cause I'm to sleepy to write it again. 🥱
I had read your post on the accelerator pump last week and checked that. No gas squirting. So I figured that was at least one of the problems.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
I got the carb all cleaned up and put back together tonight. Doubtful I will have time to get it on Ol Rusty in the next week though.
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
Well... I have pddled here and there on Ol' Rusty. I put a new fuel pump in last week, one that did not leak fuel so that was an improvement. That led to me driving to the gas station and filling up the tank. I think its been over 20 years since rusty was at a gas station so that was a big win.

1764204348791.png
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
The heater fan would not kick on. So I tackled that today. I was able to dissasemble the heater switch. I cleaned it up, put it back togehter and reinstalled it. it is working just fine now. I pulled the heater box and have the upgraded fan, seal kit and heater core in the mail. Maybe next week I will have heat in Ol rusty.

1764204561317.png

1764204578902.png

1764204601201.png
 
OP
OP
J

jba6555

Full Member
Joined
Oct 29, 2007
Messages
193
It was warm enough today that if I broke down i would not be too mad. So, I drove Ol Rusty to work. Just 2 miles to work. Ol Rusty could also be called "The Wanderer" there is a lot of play in the steering on that ol guy. The big issue I found on my way to work is that Ol Rusty never shifted out of 1st. So I have some work to do there. All the guys at work were excited to see it and hear me fire it up. It popped right off a few times over the course of the morning. Then at noon I went to go home, and Ol Rusty just wouldnt fire. So I caught a ride home. I had some lunch, grabbed a bit of gas in a squirt bottle and went back to work.

I put a squirt of gas in the carb and went to fire him up... Same as earlier in the day. So I am thinking it must be on the spark side of things. I had a busy evening so He is still sitting at work. Any thoughts on what it might be?

1765336902373.png
 

Bruners4

Full Member
Joined
Jul 22, 2019
Messages
286
Loc.
1/2 way to everywhere
With a points ignition system, I would be looking at the condenser after verifying that you have positive voltage to the points. Coil could also be suspect.
 
Top