• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Track width

panteramatt

Sr. Member
Joined
Mar 11, 2011
Messages
677
Putting new wheels on my 74. Even stock ,the front width is 1" wider than the rear. I wanted to either make the rear the same width or make it slightly wider. If I go 1/2" on each side I would need new longer studs. If i go 1" I would only need billet spacers. Would th erer being 1" wider make the bronco steer and handle weird?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Did you measure yours to get that track width measurement? Over the years I’ve seen specifications showing that some years were the same width, some years were slightly skewed, but I don’t know if those were accurate or just marketing numbers.

Sorry, I don’t have an answer as to whether it would handle weird or not. But any change on a short wheelbase vehicle is likely to at least be felt by the driver. For good or bad…
 
OP
OP
P

panteramatt

Sr. Member
Joined
Mar 11, 2011
Messages
677
I measured the old wheels from sidewall to sidewall and the front is 1: wider than the rear so I was thinking of making the rear 1" wider. I mean most of the sports cars I ever had where way wider in the rear
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I’m not against the trying part. Just not sure you’ll feel anything saying “improvement” in regards to road manners.
But if it’s more about the look, then that’s a personal thing. I don’t necessarily like the look of the front being notably wider than the rear, but I never noticed it on Broncos either.
My F350 looks funky with the wider Dana 60, and I was never fond of the’73-‘91 GM trucks with their wider front track. Just never noticed it with the Broncos.

Have you swapped to disc brakes yet? Are you going to?
If it’s in the future, I would do that first. Then re-measure.
Just in case there is a change.
 

Bung72

Contributor
New Member
Joined
Nov 29, 2025
Messages
32
Loc.
Ripon, Wisconsin
The rear of mine is an inch narrower than the front. Be driving it 50 years in February and never noticed any odd handling or weird tire wear.
 

serial car restorer

Yes, I'll restore almost anything...
Joined
Aug 27, 2024
Messages
742
Loc.
Western Oregon
I measured the old wheels from sidewall to sidewall and the front is 1: wider than the rear so I was thinking of making the rear 1" wider. I mean most of the sports cars I ever had where way wider in the rear
Sports cars are one thing. Four wheel drives are another. I know that my old Chevys ('69 K10 & '79 K20) had narrower track in back also, and I don't think that's at all unusual for 4x4 trucks. Not sure if there is a reason other than simple packaging. But since Ford could have easily built the rear 9" a little wider, there's probably a reason. I wouldn't do it, myself.
 

Speedrdr

Contributor
Legend in my own mind
Joined
Nov 27, 2017
Messages
2,028
Loc.
Paris, MS
Don’t know if there’s any truth to it, but years ago (40+) I was told it was done that way to help keep you from having the rear tires completely in the front tire tracks. Supposed to help keep you from getting stuck.
Always thought that was a load of BS myself.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
It was probably more due to initial design, trying to optimize Ackerman angle, steering performance, road manners and packaging, than anything else.
Lots of things fell in step with that. Such as the tires not tracking in the same groove, which I had read as well, way back when.

I also remember them saying that the reason for the different gear ratios in the front and rear differentials on some trucks was to let the front end pull rather than be pushed by the rear. When it really had nothing to do with that.
Had everything to do with front and rear differentials being made by different companies.
 
Top