• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel Pump Question

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
So I've got a mechanical fuel pump...if I want to upgrade to an electric pump, can I install and let the line still run through the mechanical--or I get no advantage and need to re-route directly to the carb?

I'm guessing that the real advantage is not getting to the front of the Bronco and to the mechanical fuel pump--but getting it up to the carb. Still, I'm asking.

Second question: If I do reroute an electric fuel pump to the carb, do I remove the mechanical pump? And if I remove it, do I have to put a plate or something where it was?

Thanks in advance! Dan
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
If you remove, you will need to install a plate over mounting hole.

I would not run line through old pump, it will still try to pump if mounted. I would run a line from inlet of mech pump to carb, maybe even use old mech pump output line to carb and install a clear fuel filter inline there.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I wouldn’t run it through the pump either.
If for no other reason, modern fuels and modern mechanical pumps don’t like each other. The pumps tend to die early deaths.
Which means that, in fairly short order, your perfectly fine electric pump might soon be pumping gas into your engine crankcase and/or out through the vent hole.
Neither of which is a good thing!
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Assuming no failure of the mech pump it won't hurt it. I've done it, but not an a Bronco. Used an impulse pump to get fuel to the carb after that vehicle had sat for a long period, which it did frequently. Saved a bunch of cranking.

But yeah, I wouldn't route it thru the mech pump either. Not from a failure mode fear, but from a vapor lock consideration. The mech pump will put engine heat into the fuel just by being in the system.
 

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
So I've got a mechanical fuel pump...if I want to upgrade to an electric pump, can I install and let the line still run through the mechanical--or I get no advantage and need to re-route directly to the carb?

I'm guessing that the real advantage is not getting to the front of the Bronco and to the mechanical fuel pump--but getting it up to the carb. Still, I'm asking.

Second question: If I do reroute an electric fuel pump to the carb, do I remove the mechanical pump? And if I remove it, do I have to put a plate or something where it was?

Thanks in advance! Dan
Yes I would remove the existing mechanical pump, go to any speed shop they have the cover plates. While there pick up a fuel pressure regulator. Most electric pumps are pushers so mount the pump as close to the tank as possible.

From the pump run to the regulator then to carb. Keep your fuel pressure in the 3 to 4 range for stock carburetor.

Most importantly be sure to use a relay when wiring the new pump.
 
Last edited:

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
For the mech pump blank-off plate, the thicker the better and avoid chrome because sealing those can be a problem.
 
OP
OP
70 sport WA

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
Assuming no failure of the mech pump it won't hurt it. I've done it, but not an a Bronco. Used an impulse pump to get fuel to the carb after that vehicle had sat for a long period, which it did frequently. Saved a bunch of cranking.

But yeah, I wouldn't route it thru the mech pump either. Not from a failure mode fear, but from a vapor lock consideration. The mech pump will put engine heat into the fuel just by being in the system.
And that's the problem I've had in the past (vapor lock)...no issues in regular street use, no problem in 90 degree weather in a parade going 5 mph, no overheating...but angles up in the foothills, yeah, not good. But even regular street use, there does seem to be some "lag" at times and I'd rather just get the fuel to the carb fast.
 
OP
OP
70 sport WA

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
Yes I would remove the existing mechanical pump, go to any speed shop they have the cover plates. While there pick up a fuel pressure regulator. Most electric pumps are pushers so mount the pump as close to the tank as possible.

From the pump run to the regulator then to carb. Keep your fuel pressure in the 3 to 4 range for stock carburetor.

Most importantly be sure to use a relay when wiring the new pump.
OK...helpful, thank you(!) and some questions:

The fuel pressure regulator. I understand that the pump should be as close to the tank as possible...but does it matter where the regulator goes? And does the regulator need some power source (wired)?

I have stock carb, so thanks for the recommended pressure range.
And for you and others in this thread...can I just order a plate from somewhere, like WH or our other preferred vendors? It's a 302.
 
OP
OP
70 sport WA

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
I remember when my mechanical fuel pump started failing in another Bronco, back around 1994...I had owned two by that time, now it's been four. How I even figured out what to do without the Internet, don't ask (maybe Chilton book?) $11 pump from NAPA and three screws, lots of gasoline on my hands, nothing burger. Fun times.
 
OP
OP
70 sport WA

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
One more question...I havre dual tanks. The main is newer...installed like 10 years ago, Wild Horses, while the aux is original.

I have no idea how all of the fuel tubing is set up unless I crawl underneath, which I can do. But in this case, so I still set up the electric fuel pump at the back of the vehicle? Probably sounds stupid (does to me as I'm typing this) but does it need to be forward of the aux as least common denominator?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
One way is to mount the pump in front of the switching valve and simply put it in the output line/hose of the valve. This is the simple method, but dictates that you have a good quality pump that does not mind pulling a bit more than pushing.
You could always re-route the output hose of the valve to allow the pump to be mounted back by the main tank, or somewhere between the main and aux tanks. But this does not really change the dynamic of still needing a pump that can pull as much as push. Because the pump might be mounted close to the tank, but it's still pulling through all the extended length of hose.
The only real reason I can think of for doing it that way, is so that if it turns out the pump doesn't like pulling, it's already mounted near the tank and can be re-plumbed into a pusher.:rolleyes:;)

I did not finish mine (still ran mechanical right up until I stopped driving it), but the layout was to convert the switching valve to electric, move it back along the frame rail closer to the middle between the two tanks, then plumb the pump(s) to the output hose of the valve just like you would have done in the first scenario.
The only real difference I could see, would be that it is now pulling through less hose, because of the shorter run from the tanks. Especially the main tank.
Might not be a big difference, but with electric pumps it's often the little things that make the difference.
Heck, I've seen "pusher" pumps mounted up on the wheel well by the engine that worked for years. But then suddenly didn't!
It's the "suddenly didn't" that you have to plan for, and hope to not encounter it.

You still have to contend with the lack of available real estate under an EB, just as with most custom mods. So do whatever is the most expedient and hope it's also the most efficient!
There are probably as many different mounting schemes as there are members here who have gone inline/external electric!

Good luck.

Paul
 

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
OK...helpful, thank you(!) and some questions:

The fuel pressure regulator. I understand that the pump should be as close to the tank as possible...but does it matter where the regulator goes? And does the regulator need some power source (wired)?

I have stock carb, so thanks for the recommended pressure range.
And for you and others in this thread...can I just order a plate from somewhere, like WH or our other preferred vendors? It's a 302.
Nope you can put the regulator anywhere. Just make sure its a solid mount, its s gas line you don't want it moving around.

Most automotive shops will have the pump delete plates in stock.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
This is one of those systems that I treat with the KISS philosophy. That means simply replacing just the parts that fail. The Carter OEM pumps are cheap and easy to find, so that's the easiest fix. Mine have lasted 5-10 years, before oil sprays out the weep hole. Ford put return lines on some of the 80s small blocks but I think that was a result of new alcohol mixtures percolating in the fuel line of some cars. My 68 EB didn't have that problem. An electric pump can pre-fill the float bowels but a nippon denso starter fixed that by taking the worry out of a few extra seconds cranking.
Always put fuel filters between the pump and the carb or on the carb. The fuel pressure before the pump drops and invites percolation.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
From the factory there is a filter before the pump. It is the pickup sock in the tank.
I am not opposed to a pre-pump filter. As long as it is a coarse screen just to keep big things out (high micron number, 100+)
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
IF the regulator is of the by-passing type (the only type that I use) then you'll want it as close to the carb as you can reasonably mount it. The reason is that the supply line is under pressure, and like coolant, fuel boils at a higher temperature as the pressure goes up. The line between the regulator and the carb is at a lower pressure so fuel boiling, vapor lock, can happen there more easily. Makes sense to me to keep this section of low pressure fuel as short as possible.

If you opt for in-tank or inline pumps with robust check valves in them or add them to the pump's discharge plumbing, and you have no return line, then the switching can be purely electrical powering of the pump in the tank that you want to draw from. As a general rule electric fuel pumps push better than they pull. Placing them at the tank(s) and keeping the suction line as short as possible will reduce the opportunity for vapor lock-like symptoms. Just like how raising the pressure on fuel increases it's boiling point, reducing the pressure on fuel lowers it's boiling point. Fuel pumps are also cooled by the fuel flowing thru them when an inline pump, but both by the fuel flowing thru them and and by the fuel that they're immersed in with an in-tank pump. Another reason why I prefer by-passing regulators and fuel return plumbing, keep that fuel moving so that it has less chance to get hot. The Wagon's fuel system needs to be replaced (it's all hose!) when the new EFI engine goes in and when I do that job it will be getting a small stacked plate cooler in the return line. An OEM 6.6L Duramax showed me that trick.
 

Grey owl

Contributor
Sr. Member
Joined
Nov 19, 2024
Messages
398
From the factory there is a filter before the pump. It is the pickup sock in the tank.
I am not opposed to a pre-pump filter. As long as it is a coarse screen just to keep big things out (high micron number, 100+)
If you are asking the pump to pull make sure any filter between tank and pump is HIGH FLOW. I would not put a filter in that line. There is already a filter on the pick up. Fuel filters are used to protect the carb or EFI only. No point asking it to do something it was not designed to do.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
If you are asking the pump to pull make sure any filter between tank and pump is HIGH FLOW. I would not put a filter in that line. There is already a filter on the pick up. Fuel filters are used to protect the carb or EFI only. No point asking it to do something it was not designed to do.
I was going back to as designed system. Most aftermarket tanks just have an open line in the tank as the pickup point when the factory used a sock. If you can't do a sock in the tank, a coarse high flow inline filter before the pump. One or the other, not both.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
The aftermarket tank in my '70 is like that, only has a tube sticking out for the fuel supply. No idea what it may or may not have on the other end of that tube. No way to access it that I know of short of cutting it open.
Built a ~100 micron pre-filter for a previous project since it too had no sock the way that the OEM built it. I used an Aeromotive inline fuel filter body and made a new filter element from some 100 micron filter mesh and the end-caps from the supplied filter element.
 
OP
OP
70 sport WA

70 sport WA

Contributor
Sr. Member
Joined
Nov 1, 2003
Messages
781
OK...I'm thinking another route. Some investigation shows there's a difference between mechanical pumps in terms of "gallons per hour" or "GPH."

I need to get under the Bronco to see what's there.

I changed out the mechanical pump on another rig 30 years ago, so no mystery--but will a stock or "regular" mechanical pump that has output of 80 GPH be much different than 120 GPH?

I have stuck in my mind a few years ago going in some rough crawling in New Mexico and my fuel delivery not keeping up with expectations. Stalled out, whether it was vapor lock or delivery.

But on the road before and afterward, not bad. Butr I now have a greater sense some delivery issues and road could be improved. I'm mostly on the road.

So...will I going from a 80 GPH (if that is what I have now) to a 120 GPH see a noticeable improvement on the street and rare rock climbing/rough terrain...or should I go electric pump fuel delivery?
 
Last edited:
Top