• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Disconnect Wiring Help

OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Thanks again!

So I can just disconnect the one stock black charge wire from the alternator and cap it off / move it out of the way?

Good point about the horn. Not sure I care very much about using it when power is diconnected, but worth considering.

That is a buss bar in the diagram; the switched side of the disconnect would have the black harness connection "(labeled "To vehicle harness/loads" in the diagram), which is not connected to the battery in any other way, so it should work as a disconnect I think. I'm okay with the starter being connected directly to the battery because the ignition switch won't work with the harness disconnected.

I'm also planning to replace the ammeter with the voltmeter from WH.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Use a better contactor and the wiring gets simpler because you can run starting and winching power thru it. Not a fan of those unsealed C-H contactors.

 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
So I can just disconnect the one stock black charge wire from the alternator and cap it off / move it out of the way?
Correct. You can even use it as an alternate power source for a small auxiliary fuse panel, or power distribution stud/block if you want.
After all, it's a nice 10ga wire connected directly to the battery if you think about it. Just size the loads wisely, since it's probably about 10' long at that point.
But it's handy as heck.
Good point about the horn. Not sure I care very much about using it when power is diconnected, but worth considering.
Exactly. No right or wrong way, or one way more important than the other. Just something else to consider when laying it all out in your head.
That is a buss bar in the diagram; the switched side of the disconnect would have the black harness connection "(labeled "To vehicle harness/loads" in the diagram), which is not connected to the battery in any other way, so it should work as a disconnect I think. I'm okay with the starter being connected directly to the battery because the ignition switch won't work with the harness disconnected.
Correct. But there's still the remote possibility that the starter can short out somehow, and start cranking even without input from the chassis harness.
Pretty sure it's a rarity, but I've seen it happen.
It's why I'm still on the fence as to which way is best to connect the modern PMGR starters.
But only slightly on the fence. As the likelihood of it running-on when you release the key, is much greater than the chance the relay will experience a short and stick closed.
I'm also planning to replace the ammeter with the voltmeter from WH.
Cool. Thanks!
I think most are happier with a volt-meter than they ever were with their ammeter. There is a stigma around them still, that is not germane to Bronco ammeters. But they're more finicky and most people are used to referencing a volt-meter anyway.

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
I finished wiring everything up today. It got a little busy, but should be well protected and sufficient for current and future use. I’ve got a ways to go on other things before I get the battery back in and try to start the engine, so hopefully it all works in a couple weeks when I’m ready to try…

IMG_5816.jpeg


I did save the original black harness wire and put it on a distribution post on the inner fender, just in case it comes in handy someday:

IMG_5791.jpeg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Looks like you are still utilizing the stock external voltage regulator with that alternator. If so, you need to make sure that there is a ground wire connected between the case of the alternator, and one of the mounting bolts on the regulator. They need to share the same ground value. I forget the exact term at the moment, but "value" should do the trick.

Reason I bring that up is that I see the ground "ring" there in the second pic next to the new distribution stud.
The molded rubber strain-relief that encompasses the old Black wire, a White w/black trace wire (for '73 and later Broncos), and possibly even the Orange Field wire(?) has a mounting ring sticking out of it. That ring is actually the ground end, connected to the tiny Black wire going up to the regulator.
Since the whole assembly is disconnected now, the ground has to be re-connected somehow.

And regarding your first pic (nice wires by the way!), I'm still trying to determine where everything goes. Looks like I'll have to go back and review your drawing.
Did you get it done like the previous drawing? Or did you make any running changes to the order/location of your wires?

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Thanks, I’m glad I posted a follow-up as I wasn’t considering the ground. That ground ring was already disconnected; the PO put a ground wire straight from the regulator to the battery terminal connector, so I’m assuming the ground from battery - block - alternator was “close enough”?

So it would be best to run a ground wire straight from the alternator case to the regulator? Can I use the bottom unused post on the back of the alternator?

IMG_5817.jpeg


And yes, I wired it just like the diagram. The distribution block and mega fuses are bulky, so it’s a little zig-zagged.

Here’s a pic before it was totally done. Bottom post of the distribution block connects battery and starter cable. Next one up is alternator charge cable, looping down to go through the fuse, then the next one up is the starter solenoid (smaller wire with inline fuse), then the top post is the battery disconnect (powering main harness), which had to loop up around the left side of the fuse for the straight shot down from the right side to the disconnect.

IMG_5806.jpeg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
That ground ring was already disconnected; the PO put a ground wire straight from the regulator to the battery terminal connector, so I’m assuming the ground from battery - block - alternator was “close enough”?
Probably, but not really sure.
The standard factory practice was a wire directly between the two. But remember, another "factory practice" was to keep costs to a minimum, which meant wire sizes and lengths.
With that in mind, they HAD to put at least a small one between the two components to retain the same ground potential. That's the word I was looking for last night!
Your multiple ground points were probably adequate, being likely of a larger gauge wire. But potentially losing some ground, if one of the connections got loose or corroded.
So it would be best to run a ground wire straight from the alternator case to the regulator? Can I use the bottom unused post on the back of the alternator?
Yes. There is a stud marked "GRD" back there somewhere, but it's usually in an awkwierd location on Ford applications, so any one of the small studs that is not insulated from the main case, or even a mounting bolt, would be sufficient and correct.
Here’s a pic before it was totally done. Bottom post of the distribution block connects battery and starter cable. Next one up is alternator charge cable, looping down to go through the fuse, then the next one up is the starter solenoid (smaller wire with inline fuse), then the top post is the battery disconnect (powering main harness), which had to loop up around the left side of the fuse for the straight shot down from the right side to the disconnect.
So now, the original starter relay's only duties are to energize the piggyback solenoid on the starter, and to let the Brown "I" wire add some juice to the ignition circuit during START. Correct?
Normally for that application you'd probably use a 10g or 12g wire. But yours looks to be pretty short, so you can probably get away with the smaller size. Unless that is a 12ga, but looks smaller next to all of those big-boy cables!
Out of curiosity, what is the rating on the inline fuse?
And the rating on the fuse to protect the wire going back up into the cabin and factory fuse panel?
I'll re-read the diagrams next time I have a chance.

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
So now, the original starter relay's only duties are to energize the piggyback solenoid on the starter, and to let the Brown "I" wire add some juice to the ignition circuit during START. Correct?
Normally for that application you'd probably use a 10g or 12g wire. But yours looks to be pretty short, so you can probably get away with the smaller size. Unless that is a 12ga, but looks smaller next to all of those big-boy cables!
Out of curiosity, what is the rating on the inline fuse?
And the rating on the fuse to protect the wire going back up into the cabin and factory fuse panel?
I'll re-read the diagrams next time I have a chance.

Paul

Right, the original solenoid is just acting as a switch to signal to the solenoid on the starter. I probably leaned on ChatGPT a little too much regarding wire and fuse sizing, as I'm now reading more about current draw for the starter solenoid on the starter itself (I thought it was really just a switch and all real power was coming from the big power cable); the wire connecting the power to the stock solenoid is only 14 awg with a 20 amp fuse. I've been trying to go heavy-duty with everything, so that's probably a weak point. Maybe I'll swap it for 10 awg and 30 or 40 amp fuse?

The fuse between the alternator and power distribution block is 150 amps (4 awg wire), and the fuse between the power distribution block and disconnect/harness is 100 amps (6 awg).
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Sure seems awfully complex for the stated goal of the main harness not being energized when the EB is sitting long term between uses. Can do that with a marine battery switch. I have two such on vehicles now and I used to have a third with a keyed Hella battery switch, but that car was sold. The car had some memory-keep-alive demands, so it had a small amp fuse in a by-pass for the battery switch. That kept the memory alive, but would blow if too much current tried to pass thru it. One, and eventually both of the other vehicles have memory issues, but I've not yet done the same for them.
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Sure seems awfully complex for the stated goal of the main harness not being energized when the EB is sitting long term between uses. Can do that with a marine battery switch. I have two such on vehicles now and I used to have a third with a keyed Hella battery switch, but that car was sold. The car had some memory-keep-alive demands, so it had a small amp fuse in a by-pass for the battery switch. That kept the memory alive, but would blow if too much current tried to pass thru it. One, and eventually both of the other vehicles have memory issues, but I've not yet done the same for them.
Agreed… I let it snowball a bit. I liked the idea of having a button I could hit from the driver’s seat to power off and on every use, and thought the disconnect would be simple, but the instructions had the full starter current going through the disconnect which I didn’t want, so then I went down the rabbit hole…. I like that I’ve upgraded the charge cable at the same time and removed amperage from the ammeter loop, but yes, complex and overkill.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I probably leaned on ChatGPT a little too much regarding wire and fuse sizing, as I'm now reading more about current draw for the starter solenoid on the starter itself (I thought it was really just a switch and all real power was coming from the big power cable); the wire connecting the power to the stock solenoid is only 14 awg with a 20 amp fuse. I've been trying to go heavy-duty with everything, so that's probably a weak point. Maybe I'll swap it for 10 awg and 30 or 40 amp fuse?
I don't think you need to change it at this point. An actual "solenoid" like you now have, as opposed to just a "relay" like Ford supplied on the fender, does take more current to operate. You're correct that the big cable handles all the real hard work of spinning the starter motor and engine over. It's just that the solenoid uses more than the old relay does by itself.
Probably not a huge deal breaker at this point though, I would not think.

As I was writing one of the previous answers, I was daydreaming about using really small fuses, rated at, for example, starting at 10a just to see where the threshold was on the solenoid. I remember talking about HEI ignitions and starter solenoids a few months ago, and wondering just how much current each one needed. There is probably a less expensive way of checking that though! No need to burn through ever larger fuses when you can just google something I suppose.
But where's the fun in that!
The fuse between the alternator and power distribution block is 150 amps (4 awg wire), and the fuse between the power distribution block and disconnect/harness is 100 amps (6 awg).
So more than enough for protecting the big cables, and keeping up with any future alternator upgrades shy of 120a or so.
Where does power for the rest of the truck come from again? And how big of a fuse protects the system in the cabin?
I know that the aftermarket harness companies like to use 60a Maxi-Fuses and Midi-Fuses, but in reality a Bronco probably only needs a 30a fuse to protect the old Black 10ga wire to the fuse panel. I like to use 40a models myself, unless there is some additional draw from added-on accessories in the truck.
Is that your 20a fuse? Where exactly does the old Black wire attach? That's on one post of the new disconnect relay/solenoid/contacteur/switch thingy. Correct?
That's the whole point of this excercise if I remember. Just cutting off power to all the rest of the truck, while not having to disconnect the main battery cables.
Protecting the starter solenoid circuit with 20a and 14g is probably fine. For the main power lead to the fuse panel, I would probably go 30 or 40 for the 10ga wire.

Paul
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
I don't think you need to change it at this point. An actual "solenoid" like you now have, as opposed to just a "relay" like Ford supplied on the fender, does take more current to operate. You're correct that the big cable handles all the real hard work of spinning the starter motor and engine over. It's just that the solenoid uses more than the old relay does by itself.
Probably not a huge deal breaker at this point though, I would not think.

As I was writing one of the previous answers, I was daydreaming about using really small fuses, rated at, for example, starting at 10a just to see where the threshold was on the solenoid. I remember talking about HEI ignitions and starter solenoids a few months ago, and wondering just how much current each one needed. There is probably a less expensive way of checking that though! No need to burn through ever larger fuses when you can just google something I suppose.
But where's the fun in that!

So more than enough for protecting the big cables, and keeping up with any future alternator upgrades shy of 120a or so.
Where does power for the rest of the truck come from again? And how big of a fuse protects the system in the cabin?
I know that the aftermarket harness companies like to use 60a Maxi-Fuses and Midi-Fuses, but in reality a Bronco probably only needs a 30a fuse to protect the old Black 10ga wire to the fuse panel. I like to use 40a models myself, unless there is some additional draw from added-on accessories in the truck.
Is that your 20a fuse? Where exactly does the old Black wire attach? That's on one post of the new disconnect relay/solenoid/contacteur/switch thingy. Correct?
That's the whole point of this excercise if I remember. Just cutting off power to all the rest of the truck, while not having to disconnect the main battery cables.
Protecting the starter solenoid circuit with 20a and 14g is probably fine. For the main power lead to the fuse panel, I would probably go 30 or 40 for the 10ga wire.

Paul
Thanks!

The original black power wire to the harness, connected to the disconnect, has an inline 30 amp fuse (was like that when I bought it).
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
As I was writing one of the previous answers, I was daydreaming about using really small fuses, rated at, for example, starting at 10a just to see where the threshold was on the solenoid. I remember talking about HEI ignitions and starter solenoids a few months ago, and wondering just how much current each one needed. There is probably a less expensive way of checking that though! No need to burn through ever larger fuses when you can just google something I suppose.
But where's the fun in that!

Milwaukee 2237-20 600V 600A AC/DC clamp-on ammeter or similar. Most expensive than a fuse selection, but a better overall tool.
 
Top